HiB NOVUM N19FS50MBL User manual

Fitting Instructions
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
FABRICA FLOOR STANDING
Midnight Blue: Art Nos. N19FS50MBL / N19FS60MBL
Dark Emerald: Art Nos. N19FS50DEM / N19FS60DEM
Carbon Grey: Art Nos. N19FS60CGR / N19FS60CGR
FI#03 019 R210706 Ver 1.0 Oct 2021

2
• Please read the instructions and warnings carefully before installing the
product and ensure this document is kept with the product for future
reference to ensure product longevity and in the interest of safety.
• This product is intended for domestic use only.
• Not for use in saunas, steam rooms.
• It is recommended that this product is installed by 2 people who are able
to meet the level of competence required in order to comply with relevant
regulations.
• This product is designed for installation into a brick or masonry block wall. If
mounting onto other substrate, ensure appropriate fixing and batons are used
(if required) and the load bearing of the wall is sufficient.
• When drilling use appropriate eye protection.
• Take care when using power tools near water - the use of a residual current
device (RCD) is advised.
• Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case
the drill slips.
• Do not overload shelves or unit.
• Do not sit or stand on the unit.
• Ensure that excessive standing and surface water is removed from the product
to avoid long term damage and spoiling.
Warnings for Safe Use

3
hib.co.uk
What’s in the Box?
Tools Required
• Fabrica Floor Standing Unit
• Fitting pack
• Sealant bottle
Screwdriver Pencil
Suitable
Drill Bit
Tape
Measure
Spirit Level Drill

4
Figures
Fig. 1
Fig. 2 Fig. 3
a
a

5
hib.co.uk
Installation
1. Plan the position of the unit on the wall.
2. Mark the drill location onto the wall through the pre-drilled holes in the rear
cross rail of the unit. See Fig. 1.
3. Drill holes in wall and fix the unit into position with suitable fixings.
4. Silicone along the top edge of the unit and fit the basin as per Fig. 2. Silicone
along back edge of basin and along the back of the unit and wall as per Fig. 3.
Allow to set fully.
5. Fix tap in place, and finalise water and waste connections. If the waste pipe and
water feeds are routed from the floor, then the base of the unit will need to be cut
to accommodate this. Do not remove more material than necessary. All cut edges
must be sealed with the sealant provided to prevent water ingress.
6. Secure handles in place using the pre-drilled holes in the drawers.

6
Adjustment & Removal
Fig. 4 - Removal Fig. 5 - Adjustment

7
hib.co.uk
Care
Aftercare
In the unlikely event that this product should fail please contact the retailer from
which the item was purchased.
To preserve the high quality finish of your HiB product, please ensure you regard
the following care and cleaning recommendations:
• Use only a so damp cloth.
• Wipe off all water spillages as soon as possible.
• Do not use any abrasives or solvents.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try
and make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary.
E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN