HiB novum N19WH50MBL User manual

Fitting Instructions
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
FABRICA WALL HUNG
50cm Midnight Blue: Art No N19WH50MBL /50cm Carbon Grey: Art No N19WH50CGR
50cm Dark Emerald: Art No N19WH50DEM
60cm Midnight Blue: Art No N19WH60MBL /60cm Carbon Grey: Art No N19WH60CGR
60cm Dark Emerald: Art No N19WH60DEM
Fabrica 50cm Wall Hung
Fabrica 60cm Wall Hung
FI #03 017 R201013 Ver 1.0 Jan 2021

2
• Please read the instructions and warnings carefully before installing the
product and ensure this document is kept with the product for future
reference to ensure product longevity and in the interest of safety.
• This product is intended for domestic use only.
• Not for use in saunas, steam rooms.
• It is recommended that this product is installed by 2 people who are able
to meet the level of competence required in order to comply with relevant
regulations.
• This product is designed for installation into a brick or masonry block wall. If
mounting onto other substrate, ensure appropriate fixing and batons are used
(if required) and the load bearing of the wall is sufficient.
• When drilling use appropriate eye protection.
• Take care when using power tools near water - the use of a residual current
device (RCD) is advised.
• Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case
the drill slips.
• Do not overload shelves or unit.
• Do not sit or stand on the unit.
• Ensure that excessive standing and surface water is removed from the product
to avoid long term damage and spoiling.
Warnings for Safe Use

3
hib.co.uk
What’s in the Box?
Tools Required
• Fabrica Unit
• Fitting Pack
• Connecting bolts
Screwdriver Pencil
Speed
Clamps
Suitable
Drill Bit
Tape
Measure
Spirit Level Drill

4
Figures
Recommended Install Heights
a
3
42
1
a
830mm
Fig. 1 - Recommended Install Heights
Fig. 2
Fig. 3 Fig. 4
740mm 900mm

5
hib.co.uk
Installation
Please ensure the wall is suitable for wall hung furniture. For stud wall
installations, add an extra timber support into the stud wall prior to finishing
the wall to improve strength.
1. HiB recommends removing the drawers prior to installation. See Fig. 5., overleaf.
2. Plan the unit position on the wall. HiB recommend the installation heights shown
in Fig. 1. Take note of the height of the optional leg kit if it is being installed.
3. If the optional leg kit is to be installed, turn the unit upside down on a so
surface. Establish the leg position. Pilot drill and screw the legs into place with the
supplied screws.
4. Measure the spacing on the back of the unit, between the two inner sides of
the carcass (Fig. 2, A) this is the maximum bracket spacing. Measure the required
mounting point height taking into account the basin to be used and if leg kit is
being installed.
5. Transfer measurements onto wall using a spirit level to ensure they are straight
and level and spaced correctly as per Fig. 2.
6. Drill holes for wall brackets and fix into position with suitable fixings.
7. Position the unit(s) onto the wall brackets.
8. Use furniture hangers to adjust alignment of furniture unit(s) (Fig. 7, screw B,
overleaf), ensuring that they are level.
9. If installing multiple units side by side, once they are both in the correct position,
clamp them together using speed clamps and fix together using the fixings
provided, as per Fig. 3.
10. Once the unit(s) are in position, adjust the screw on the furniture hanger (Fig. 7,
Screw A, overleaf) to bring the furniture tightly against the wall.
11. Silicone along the top edge of the unit and fit basin/countertop on top. Silicone
along back edge of basin/countertop and along the back of the unit and wall as
per Fig. 4. Allow to set fully.
12. Fix basin and tap in place and finalise water and waste connections.
13. Refit the drawers and secure handle in place, using the predrilled holes in the
drawer fronts.

6
Adjustment & Removal
+
+
a
b
Fig. 5 - Removal Fig. 6 - Adjustment
Fig. 7

7
hib.co.uk
Care
Aftercare
In the unlikely event that this product should fail please contact the retailer from
which the item was purchased.
To preserve the high quality finish of your HiB product, please ensure you regard
the following care and cleaning recommendations:
• Use only a so damp cloth.
• Wipe off all water spillages as soon as possible.
• Do not use any abrasives or solvents.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try
and make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary.
E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN