HiB Vanquish 50 User manual

Fitting Instructions
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
VANQUISH CABINET
Vanquish 50: Art No 47600 / Vanquish 60: Art No 47700
Vanquish 80: Art No 47800 / Vanquish 120: Art No 47900
VANQUISH TRIM SET
BLK 50: Art No 55100 / BBR 50: Art No 55500
BLK 60: Art No 55200 / BBR 60: Art No 55600
BLK 80: Art No 55300 / BBR 80: Art No 55700
BLK 120: Art No 55400 / BBR 120: Art No 55800
FI#02 015 R220830 Ver No. 1.0 Oct 2022

2
Electrical Safety Information
Warnings for Safe Use
HiB recommends that all electrical bathroom products must be installed
in accordance with current building and wiring regulations.
If in doubt please contact an electrician.
Before drilling ensure that there are no hidden cables or pipes in the wall.
• This product is intended for Domestic Use only.
• Please read the instructions and warnings carefully before installing the
product and ensure this document is kept with the product for future
reference to ensure product longevity and in the interest of safety.
• If you give the product to another person, please give them this manual as
well.
• If any modification is made it will invalidate the warranty and may render the
product unsafe.
• This product is IP44 rated and suitable for installation in Zones 2 and Outside
Zones according to the IEEE regulations.
• It is not suitable for use in saunas, steam rooms and shower cubicles.
• Appropriate circuit protection should be available for the product.
• When drilling use appropriate eye protection.
• The use of a Residual Current Device (RCD) is advised for any power tools used
during the installation of this product.
• Take suitable precautions when handling glass.
• Beware of hidden cables or pipes. Take care if drilling on tiled surfaces in case
the drill slips.
• Always switch off the electrical supply to the product at the mains during
installation and maintenance.
• It is recommended that this product is installed by a person who is able to
meet the level of competence required in order to comply with relevant
regulations. If in doubt consult a qualified tradesperson.
• Do not enter IP44 box unless competent and item is isolated from mains.
• Do not use if glass is broken or unsafe.
• Do not use if any electrical wires appear damaged or degraded.
• Do not overload shelves or unit.
• This product is designed for installation into a brick or masonry block wall,
if mounting onto other substrate ensure appropriate fixing and batons (if
required) are used and the load bearing of the wall is sufficient.
• It is recommended that this product is installed by two people.
• Dispose of packaging in accordance to local authority regulations.
• At end of life dispose of item according to local authority regulation.

3
hib.co.uk
Electrical Information
This product contains a light source of energy efficiency class E
All installations must comply
with guidelines which are
based on a zonal concept
and must be followed to
ensure the safe installation of
electrical appliances in the
bathroom.
These regulations apply to
domestic installations only.
Installations must be made in
accordance with the current
IEE wiring regulations and
relevant building regulations.
This product is IP44 rated and is suitable for installation in zones: 2& Outside Zone
Wiring Diagram
Fig 1. - Zonal Diagram
What’s in the Box?
Cabinet and Trim set sold seperately.
Vanquish Cabinet:
• Vanquish Cabinet
• Glass shelves
• Mounting bracket
• Fittings pack
Trim Set:
• Trim
• Fittings pack
live
earth
neutral
MAINS SUPPLYLUMINAIRE
Live supply can be Red or Brown
Earth supply is Green and Yellow
Neutral supply can be Blue or Black
Live is Brown
Earth is Green and Yellow
Neutral is Blue

4
Tools Required
Adjustment
Pencil Spirit Level Drill Drill bit Screwdriver
Door Adjustment
Door Removal
Move door(s) up/down
Move door away/towards
the cabinet Move door(s) le/right

5
hib.co.uk
Figures
Fig 2.
Fig 5.
Fig 3.
Fig 6.
Fig 4.
Noggins

6
Cabinet Installation
Before installation, ensure the domestic electrical mains supply to which the
cabinet is to be connected is turned off. Before drilling, ensure that there are
no hidden cables or pipes in the wall.
It is recommended that this product is installed by two people.
This product can only be recessed fitted into a wall. Before installing ensure
you take note of measurements of the recessed area and the side fixing
points inside the cabinet carcass (See fig. 2 & 5).
You may need to remove the door / doors to make it easier to fit, see Door
Removal page 4. Do not fit the shelves until product is installed correctly.
If a separate trim set has been purchased this will need to be fitted onto the
cabinet, prior to full installation. Please see trim set installation guide on
page 7.
1. Measure the dimensions of the cabinet carcass (excluding the front aluminium
fascia trim).
2. Using these dimensions, take a so pencil and mark the outline for the
required aperture in the wall. Take great care to mark this accurately, straight
and level.
3. Using an appropriate tool, cut or channel out the aperture in the wall where
the cabinet will fit, see Fig. 2.
4. If it is necessary, install supporting baton(s) or noggin(s) around the recessed
area, see Fig. 3, to which the cabinet can be secured. These supports must be
completely vertical and parallel to the cabinet to prevent the cabinet twisting
when fitted.
5. Connect the cabinet to the domestic mains supply according to the wiring
diagram, see page 3, and position the cabinet into the wall aperture, see Fig.
4.
6. Using a suitable screwdriver or drill, secure the cabinet into the wall aperture,
via the two holes located on the internal edge of the cabinet using the
supplied screws (two on each side) see Fig. 5.
7. Insert the metal shelf supports in desired position. Install each glass shelf into
shelf supports and tighten the plastic grub screw on the underside. This will
securely clamp the shelf into position, see Fig.6.
8. If necessary, hinges can be adjusted to reposition the door(s) see Door
Adjustment on page 4.
9. Switch mains supply back on.

7
hib.co.uk
Trim Installation
1. Detach the existing aluminium trim by removing screws located around the
edges using a suitable screwdriver.
2. Assemble the new trim set using the four supplied corner brackets and
screws, ensuring the angled joints are tight and closed. See Fig 7 & 8.
Fig 7. Fig 8.
Fig 9.
3. Slide the trim frame over the cabinet and postion in line with the securing
holes on each side of the cabinet carcass . See Fig 9
4. Secure the new trim frame in place using the supplied screws and washers
5. Follow cabinet installation instructions opposite to complete install.

Care
Aftercare
In the unlikely event that this product should fail please contact the retailer
from which the item was purchased.
To preserve the high quality finish of your HiB product, please ensure you
regard the following care and cleaning recommendations:
• Avoid leaving excessive standing and surface water on the product for
prolonged periods of time.
• Clean the product with water and a so cloth, a mild detergent may be
used if required. Ensure any excess moisture is removed aer use.
• Do not use abrasive sponges or cleaning agents.
WEEE compliance
Must not be mixed with
general household waste
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try
and make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary.
E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
Operation
Illumination ON/OFF
Touch the sensor button once.
Change the Colour Temperature of the Illumination
Touch and hold the sensor button until desired colour is obtained.
The colour temperature is set until changed again.
Heated Pad
The heated pad is only on when the cabinet is illuminated.
Charging Socket(s) and USB
Charger socket(s) are suitable for charging and powering electric razors,
trimmers and toothbrushes. Some cabinets may contain multiple charging
sockets. NB. On first use of the charger socket, inserting the plug may prove to
be stiff. Reasonable force may be required to fully insert the plug. Aer a few
uses, stiffness will ease and the socket will function as normal.