HiB Novum NF02SBU50 Series User manual

Fitting Instructions
Thank you for purchasing this HiB Novum product.
Please read through these instructions carefully and refer back to
them during installation to ensure that your product is fitted safely
and that it retains its high quality finish.
GENESIS FITTED FURNITURE
Basin Unit: Art No. NF02SBU50*** / NF02SBU60***
BTW Unit: Art No. NF02SBTW50*** / NF02SBTW60***
Single Door Unit: Art No. NF02SSDU30***
Three Drawer Unit: Art No. NF02S3DR30***
Open Shelf Unit: Art No. NF01SOS20***
End Panels: Art No. NF01SEP***
Infill Panels: Art No. NF01IP20***
Plinth: Art No. NF01PL100*** / NF01PL150*** / NF01IP200***
MBL - Midnight Blue | DEM - Dark Emerald | CGR - Carbon Grey |
MWH - Matt White | SWO - Sherwood Oak
FI#03 020 R220422 Ver 1.0 June 2022

2
• Please read the instructions and warnings carefully before installing the
product and ensure this document is kept with the product for future
reference, to ensure product longevity and in the interest of safety.
• This product is intended for domestic use only.
• Not for use in saunas or steam rooms.
• It is recommended that this product is installed by 2 people who are able
to meet the level of competence required in order to comply with relevant
regulations.
• This product is designed for installation into a brick or masonry block wall. If
mounting onto other substrate, ensure appropriate fixing and batons are used
(if required) and the load bearing of the wall is sufficient.
• When drilling and cutting use appropriate eye protection and wear an
appropriate dust mask.
• Take care when using power tools near water - the use of a residual current
device (RCD) is advised.
• Beware of hidden cables or pipes.
• Take care if drilling on tiled surfaces in case the drill slips.
• Do not overload shelves or unit.
• Do not sit or stand on the unit.
• Ensure that excessive standing and surface water is removed from the product
to avoid long term damage and spoiling.
• Seal all cut edges with a silicone or polyurethane sealant.
• When applying silicone sealant, ensure that the room is well ventilated.
Warnings for Safe Use

3
hib.co.uk
Contents
Tools Required
• Floor Standing Installation
• Plinth Installation
• Wall Hung Installation
• Door Installation
• Top Panel Installation
• BTW Front Panel Installation
• Drawer Installation
• Handle Installation
• Care & Maintenance
• Aercare
Screwdriver
Pencil
Silicone
Tape Fine Tooth
Saw
Suitable
Drill Bit
Tape
Measure
Clamps
Eye
Protection
Spirit Level
Dust Mask Drill

4
Figures
Fig. 1 - Carcass Leg Installation Fig. 2 - BTW Leg Installation
Fig. 3 - Plinth Height
Fig. 4 - Connecting Units
Standard Plinth:
H150mm
Basin Unit BTW Unit

5
hib.co.uk
Floor Standing Installation
1. Ensure all components are present before beginning installation.
2. Remove back panels and non-fixed shelves.
3. To install the legs, turn the carcass upside down on a so surface.
4. Fix the leg brackets to the base of the unit(s) using the pilot holes provided.
See Fig. 1.
5. Ensure the tab is in the correct position overlapping the carcass side panel.
See Fig. 1.
6. For a BTW unit, fix the leg bracket into the pre-drilled holes using the screws
provided. See Fig. 2.
7. Insert the legs into the leg brackets.
8. Adjust the legs to the required height by turning the feet. The HiB standard
plinth height is 15cm, see Fig. 3.
9. Position the units together in the configuration required against the wall.
Using a suitably sized spirit level, adjust the feet to level the units.
10. Clamp the units together. Using the screws and pre-drilled holes provided,
secure the units together, see Fig. 4.
11. Check the level of the units using a suitable spirit level and adjust the feet
where necessary.
12. Secure the units to the wall using the pre-installed hangers.
13. Check units are square against the wall and adjust where necessary.
14. Replace all back panels and shelves.
Screws and pre-drilled holes in the carcass have been supplied to secure the
end panels to the carcass.
To fit the countertop, please refer to the fitting instructions supplied
with the countertop.

6
Figures
Fig. 5 - Plinth Measurements Fig.6 - Plinth Return
Fig.7 - Plinth Bracket Installation
Plinth Return:
W65mm
Basin Unit
??
BTW Unit

7
hib.co.uk
Plinth Installation
1. Measure the width and height required, see Fig. 5. HiB recommends installing
plinths 2mm from the floor.
2. If installing a BTW unit, a return piece will need to be cut from the plinth. HiB
recommends a return of 65mm, see Fig. 6.
3. Always double check measurements before cutting. Cut the plinth to size.
4. Measure and mark the carcass leg centres on the back face of the plinth. See
Fig. 7.
5. Fix the brackets to the plinth using the screws provided.
6. If a plinth return is required, fix to the plinth in the appropriate location using
the screws provided.
7. Prior to installing, seal all cut edges using the sealant provided.
8. Secure the plinth to the carcass legs.

8
Figures
Fig. 8 - Recommended Install Height
Fig. 9 - Measure & Cut Panel Fig. 10 - Seal cut edges
Fig. 11 - Hanger Adjustment
830mm
1. Loosen screw
2. Adjust furniture postion
3. Tighten screw

9
hib.co.uk
Wall Hung Installation
1. Ensure all components are present before beginning installation.
2. Remove back panels and non-fixed shelves.
3. Plan the unit position on the wall. HiB recommends the installation heights
shown in Fig. 8.
4. Loosely fix the units to the wall using the pre-installed hangers in the
configuration required. Do not secure at this stage.
5. Using a suitably sized spirit level, align the units and secure together using the
predrilled holes and screws provided. See Fig. 11 for hanger adjustment.
6. Secure the units to the wall.
7. Slide the back panel back into position and replace shelves.
8. Measure and cut any end panels and infill panels required, see Fig. 9. Seal all
cut edges, see Fig. 10. HiB recommends positioning the cut edge at the top of
the unit.
Screws and pre-drilled holes in the carcass have been supplied to secure the
end panels to the carcass.
To fit the countertop, please refer to the fitting instructions supplied
with the countertop.

10
Figures
Fig. 12 - Release hinge plate Fig. 13 - Door Adjustment
Move door(s) up/down
Move door away/towards
the cabinet
Move door(s) le/right
Move door(s) up/down
Move door away/towards
the cabinet
Move door(s) le/right
Fig. 14 - Top Panel Fitting Fig. 15 - BTW Front Panel Fitting