Hib Proton User manual

Thank you for purchasing this HiB product.

Please read through these instructions carefully and refer back to them during installation to ensure that

your product is tted safely and that it retains its high quality nish.

Please retain this leaet for future reference.

Before drilling, ensure there are no hidden cables or pipes in the wall.

Proton & Neutron Cabinets

FI #02 003 R150904 Ver No. 1.0 Jan 2016

Proton

Art No.44800

Neutron

Art No.44500

Please Note

This product must be installed with a minimum distance of 150mm between the

infra-red sensor switch and any adjacent wall or object to ensure correct operation of

the sensor. DO NOT FIT SHELVES AT THIS STAGE.

Min. 150mm

Angle Adjustment

Claw In/Out

Adjustment

Claw In/Out

Adjustment

Fixing Preparation (Fig A)

Fixing Brackets (Fig B) Hanger Adjustment (Fig C)

Mounting Points

location of internal

ﬁxing hole

REAR VIEW

plasterboard walls, specialist xings should

be purchased from any DIY or hardware store.

5. Fix the brackets to the wall using the screws

provided.

6. Carefully remove the small screws along

the top front edge of the cabinet to gain

access to the internal panel(s). (Fig. C) Keep

screws in a safe place.

7. Temporarily hang the cabinet ensuring the

claws on the hangers are securely located

on the wall brackets. Using a spirit level

adjust the cabinet via the screws on the

hangers. (Fig. C).

8. Mark the position of the internal xing hole

and remove the cabinet. Using a suitable

drill bit, drill a hole and insert a wall plug as

per stage 4.

9. Connect the cable at the rear of the cabinet

to the mains supply cable using a suitable

terminal block (not supplied) according

to the wiring diagram (Fig. 2) on the back

page.

10. Rehang the cabinet in position, tighten the

screws on the hangers (Fig. C) and secure

Wall Hung Installation

1. Position the cabinet in a suitable location

(according to the zonal diagram (Fig. 1) on

the back page) ensuring that the mains

supply cable is within reach of the cable

connection point of the cabinet. Carefully

mark the desired position of the cabinet

using a soft pencil, ensuring it is level.

2. Remove the cabinet from the wall and

using a spirit level, mark a horizontal line

below the pencil mark, taking into account

the location of the mounting points (Fig.

A). Place brackets on the pencil line paying

attention to the distance netween the

hangers on the cabinet. Carefully mark the

position of the holes using a soft pencil.

(Fig. B).

3. Before drilling, ensure there are no hidden

cables or pipes behind the mounting

points. Using a suitable drill bit, drill holes

in the marked positions to a suitable depth.

4. Insert wall plugs level with the surface

of the wall. If tting to a tiled surface,

wall plugs should be inserted below the

tile surface to avoid cracking. NB. For

hib.co.uk 3

How to Isolate the sensor so you can

switch ON & OFF with a mains switch.

Rewire the cabinet as shown in the diagram

above. HiB recommends that all electrical

bathroom products should only be tted by a

suitably qualied, Part P registered electrician.

For further assistance on isolating the sensor

please contact us.

Tel: 020 8441 0352 Email: [email protected].uk

Door Adjustment (Fig D)

Operating Instructions

To turn illumination on or o, wave hand under

the sensor switch located underneath the

cabinet.

live

earth

neutral

How the cabinet is wired.

Shaver socket/transformer

Sensor switch controller

LED driver

INOUT

live

earth

neutral

How to isolate the sensor.

Shaver socket/transformer

Sensor switch controller

LED driver

INOUT

Attachment Light Fitting (Fig E)

the base of the cabinet with the supplied

screw and screw cap.

11. Once fully secure, close the internal

panel(s) using the screws removed at stage

12. Fit shelves in desired positions using metal

shelf supports.

13. If necessary, the hinges can be adjusted in

order to reposition the door(s) (Fig. D).

14. Attach the LED light tting on the top of

the cabinet using the pre-drilled holes and

screws provided. Push the male and female

electrical connector together until they

‘click’. (Fig. E).

15. Switch the mains supply back on.

This product is suitable for installation in zones: 2 &Outside Zone

All installations must comply with guidelines which are based on a zonal concept. The diagram above

illustrates this concept and must be followed to ensure the safe installation of electrical appliances in the

bathroom. These regulations apply to domestic installations only. Installations must be made in accordance

with the current IEE wiring regulations and relevant building regulations. HiB recommends that all electrical

bathroom products should only be tted by a suitably qualied, Part P registered electrician.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and

make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specications as necessary. E & OE.