HiB Jupiter 43600 User manual

Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to them during installation to ensure that
your product is fitted safely and that it retains its high quality finish.
Please retain this leaflet for future reference.
Before drilling, ensure there are no hidden cables or pipes in the wall.
Please Note Atomic & Electron cabinets must be installed with a minimum
distance of 150mm between the infra-red sensor switch and any surface or
object to ensure correct operation of the sensor.
FI #02 008 R150923 Ver No. 1.0 Jan 2016
Aluminium Cabinets
Kore
Art No. 43900
Jupiter
Art No. 43600
Callisto
Art No. 44100
Mercury
Art No. 43700
Nitro
Art No.42400
Quantum
Art No. 42500
Atomic
Art No. 42700
Electron
Art No. 42600
Min. 150mm
Min. 150mm
LED Cabinets

2
Installation
1. Atomic & Electron Only: Attach the
LED light fitting on the top of the cabinet
using the pre-drilled holes and the screws
provided. Push the male and female
electrical connections together until they
‘click’ (Fig. A).
2. Position the cabinet in a suitable location
and carefully mark the position of the top of
the cabinet using a so pencil.
3. Remove the cabinet from the wall and
using a spirit level, mark a horizontal line
50mm below the pencil mark. Hold the
mounting bracket in place with the holes
corresponding with the marked line. Ensure
the bracket is central, and mark the position
of the holes (Fig. B).
4. Before drilling, ensure there are no
hidden cables or pipes behind the
mounting points. Drill the required holes in
the marked positions. If drilling through tile,
use a ceramic drill bit. Insert the wall plugs
level with the surface of the wall. If fitting to
a tiled surface, wall plugs should be inserted
below the tile surface to avoid cracking.
NB. For plasterboard walls, specialist fixings
should be purchased, available from any
DIY or hardware store. Fix the bracket to the
wall using the screws provided.
5. Kore, Callisto, Quantum, Nitro, Atomic
& Electron: Temporarily hang the cabinet
on the top bracket, and position the bottom
mounting bracket into the slot underneath
the cabinet. Mark the position of the bracket
using a so pencil, then remove the cabinet
from the wall (Fig. C 1).
Mercury & Jupiter: Temporarily hang the
cabinet on the top bracket and mark the
position of the bottom mounting hole onto
the wall. remove cabinet and drill into the
wall as per step 4 (Fig. C 2).
6. Kore, Callisto, Quantum, Nitro, Atomic
& Electron: Place the bottom bracket on
the previously marked line and mark the
positions of the holes. Using the same
method as before, drill the required holes
and attach the bracket to the wall using the
screws provided.
Kore, Callisto,
Quantum,
Nitro, Atomic
& Electron
only
=
Attachment Brackets (Fig B)
7. Atomic & Electron Only: This cabinet
is provided with an electrical supply
cable already fitted. This cable should be
connected to the household electrical
circuit, and connections should be made in
accordance with the latest IEE regulations.
This is a Class I product and must be
connected to Earth. Ensure the domestic
electrical mains supply to which the product
is being connected is turned off. Connect
the domestic mains supply according to
Figure 2 on the back page.
8. Hang the cabinet on the wall ensuring that
it is firmly located on both brackets. Align
doors according to Fig. D.
9. Starting with the top shelf, insert the shelf
supports in the desired position and put
shelf into place. repeat for remaining
shelves.
Attachment Light Fitting (Fig A)
Atomic
&
Electron
Only

hib.co.uk 3
Mercury & Jupiter
Wall Mounting (Fig C)
Door Adjustment (Fig D)
12
Shelf Assembly (Fig E)
Kore, Callisto,
Quantum, Atomic,
Electron & Nitro

Atomic & Electron are suitable for installation in zones: 2 &Outside Zones
All installations must comply with guidelines which are based on a zonal concept. The diagram above
illustrates this concept and must be followed to ensure the safe installation of electrical appliances in
the bathroom. These regulations apply to domestic installations only. Installations must be made in
accordance with the current IEE wiring regulations and relevant building regulations. HiB recommends
that all electrical bathroom products should only be fitted by a suitably qualified, Part P registered
electrician.
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and
make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
No zonal restrictions exist for non-electric cabinets.
(Fig 1)
Wiring Diagram (Fig 2)
live
earth
neutral
MAINS SUPPLYLUMINAIRE
Live supply can be Red or Brown
Earth supply is Green and Yellow
Neutral supply can be Blue or Black
Live is Brown
Earth is Green and Yellow
Neutral is Blue
Electrical Safety Information
HiB recommends that all electrical bathroom products should only be fitted by a suitably qualified,
Part P registered electrician in accordance with current IEE regulations. Ensure mains power supply is
switched off before starting installation. Before drilling, ensure there are no hidden cables or pipes in
the wall.
Care Instructions
Do not use abrasives or solvents when cleaning this product.
Wipe off all water spillages as soon as possible using a so, damp cloth.
Aercare Service
In the unlikely event that this product should fail please contact HiB customer services, details shown
below.
WEEE compliance
Must not be mixed with
general household waste