HIK VISION DS-K1T680 Series User manual
DS-K1T680 Series Face Recognition Terminal
Quick Start Guide
©
UD21052B-C
1Appearance
Installa�on Environment:
2Installation
3.1 Wiring (Normal)
GND Black
Green
White
Yellow
Blue
Black
White/Purple
White/Yellow
Yellow/Green
White/Red
Black
Yellow/Grey
GND
GND
Yellow/Black
GND
BTN
12V Power Supply
Wiegand
Card Reader
IN2
GND
IN1
Yellow/Orange
Black
Yellow/Blue
Red
Black
Yellow/Red
Yellow/Brown
Yellow/Purple
NO
COM
NC
COM
NC
NO
COM
a
b
b
b
c
b
Alarm Input Device
Alarm Output Device
Power Supply
Alarm Output Device
Door Contact
Electric Dropbolt
Power Supply
Electric Strike
Exit Button
.
.
,
.
Model Manufacture Standard
ADS-26FSG-12 12024EPG Shenzhen Honor Electronic Co.,Ltd PG
MSA-C2000IC12.0-24P-DE MOSO Technology Co.,Ltd PDE
ADS-26FSG-12 12024EPB Shenzhen Honor Electronic Co.,Ltd PB
ADS-26FSG-12 12024EPCU/EPC Shenzhen Honor Electronic Co.,Ltd PCU
ADS-26FSG-12 12024EPI-01 Shenzhen Honor Electronic Co.,Ltd PI
ADS-26FSG-12 12024EPBR Shenzhen Honor Electronic Co.,Ltd PBR
NC
a
b
1 .
.
2 .
.
3 × ×.
(),
().
().
4
+12 V~24 VDC
6Add Face Picture
Correct Tilt Raise
Side Bow
Tips When Collec�ng/Comparing Face Picture
Expression
, .
Posture
,
Size
Correct Too FarToo Close
Posi�ons When Collec�ng/Comparing Face Picture
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your
body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
therefore with the applicable harmonized European standards listed under the RE Directive
2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
Warning
In the use of the product, you must be in strict compliance with the electrical safety regulations
of the nation and region.
CAUTION: To reduce the risk of fire, replace only with the same type and rating of fuse.
CAUTION: This equipment is for use only with Hikvision’s bracket. Use with other (carts, stands, or carriers) may
result in instability causing injury.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Please use the power adapter, which is provided by normal company. The power consumption cannot be less
than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then
please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to
disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized
repair or maintenance.)
Caution
+ identifies the positive terminal(s) of equipment which is used with, or generates direct current. + identifies the
negative terminal(s) of equipment which is used with, or generates direct current.
No naked flame sources, such as lighted candles, should be placed on the equipment.
The USB port of the equipment is used for connecting to a USB flash drive only.
The serial port of the equipment is used for debugging only.
Burned fingers when handling the fingerprint sensor metal. Wait one-half hour after switching off before
handling the parts.
Install the equipment according to the instructions in this manual.
To prevent injury, this equipment must be securely attached to the floor/wall in accordance with the installation
instructions.
Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation.
Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause
equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for the detailed operating
temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden
(ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not
a malfunction however), and affecting the endurance of sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact with the device cover,
because the acidic sweat of the fingers may erode the surface coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline
detergents.
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the
device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the
same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
Biometric recognition products are not completely applicable to anti-spoofing environments. If you require a higher
security level, use multiple authentication modes.
Please make sure that the biometric recognition accuracy will be affected by the collected pictures' quality and
the light in the environment, which cannot be completely correct.
4
Face
3.2 Device Wiring (With Secure Door Control Unit）
NO
NC
COM
NC
NO
COM
4
Steps:
Ac�vate
Activation via Device Steps Afterwards
Temperature Measurement Settings
5
Enable Temperature Detec�on:
Over-Temperature Alarm Threshold:
。
Temperature Compensa�on:
Door Not Open When Detec�ng Abnormal Termperature:
Temperature Measurement Only:
Unit:
Other HIK VISION Touch Terminal manuals
HIK VISION
HIK VISION DS-K5671B Series User manual
HIK VISION
HIK VISION DS-K1T331 Series User manual
HIK VISION
HIK VISION DS-K5032-3XFD User manual
HIK VISION
HIK VISION DS-K1T502 Series Operating instructions
HIK VISION
HIK VISION DS-K1T607 Series User manual
HIK VISION
HIK VISION DS-K5032-3XF User manual
HIK VISION
HIK VISION DS-K1T680DG User manual
HIK VISION
HIK VISION DS-K1A802A Series User manual
HIK VISION
HIK VISION DS-K11T341BMI-T User manual
HIK VISION
HIK VISION DS-K1T802E User manual
HIK VISION
HIK VISION DS-TPM400 Series User manual
HIK VISION
HIK VISION DS-K5671 Series User manual
HIK VISION
HIK VISION DS-K1A8503 Series User manual
HIK VISION
HIK VISION C2000IC12.0-24P-DE User manual
HIK VISION
HIK VISION DS-K5604A-3XF Series User manual
HIK VISION
HIK VISION DS-K1T342 Series User manual
HIK VISION
HIK VISION DS-K5604A-3XF/V User manual
HIK VISION
HIK VISION DS-K5032 Series User manual
HIK VISION
HIK VISION UD02454B User manual
HIK VISION
HIK VISION DS-TPE100 User manual
