HIMA HIMatrix F60 DI 32 01 User manual

HIMatrix
Safety-Related Controller
DI 32 01 Manual
HIMA Paul Hildebrandt GmbH + Co KG
Industrial Automation
Rev. 1.00 HI 800 203 E

HI 800 203 E Rev. 1.00 (1014)
All HIMA products mentioned in this manual are protected by the HIMA trade-mark. Unless noted
otherwise, this also applies to other manufacturers and their respective products referred to herein.
All of the instructions and technical specifications in this manual have been written with great care and
effective quality assurance measures have been implemented to ensure their validity. For questions,
please contact HIMA directly. HIMA appreciates any suggestion on which information should be
included in the manual.
Equipment subject to change without notice. HIMA also reserves the right to modify the written material
without prior notice.
For further information, refer to the CD-ROM and our website http://www.hima.de and
http://www.hima.com.
© Copyright 2010, HIMA Paul Hildebrandt GmbH + Co KG
All rights reserved
Contact
HIMA Address
HIMA Paul Hildebrandt GmbH + Co KG
P.O. Box 1261
68777 Brühl, Germany
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
Type of Change
Revision
index
Revisions
technical editorial
1.00 Added: Configuration with SILworX X X

DI 32 01 Table of Contents
HI 800 203 E Rev. 1.00 Page 3 of 38
Table of Contents
1Introduction ............................................................ 5
1.1 Structure and Use of this Manual......................................................................... 5
1.2 Target Audience..................................................................................................... 6
1.3 Formatting Conventions ....................................................................................... 7
1.3.1 Safety Notes ............................................................................................................ 7
1.3.2 Operating Tips ......................................................................................................... 8
2Safety...................................................................... 9
2.1 Intended Use .......................................................................................................... 9
2.1.1 Environmental Requirements................................................................................... 9
2.1.2 ESD Protective Measures........................................................................................ 9
2.2 Residual Risk ....................................................................................................... 10
2.3 Safety Precautions............................................................................................... 10
2.4 Emergency Information....................................................................................... 10
3Product Description .............................................. 11
3.1 Safety Function.................................................................................................... 11
3.1.1 Safety-Related Inputs ............................................................................................ 11
3.1.1.1 Reaction in the Event of a Fault............................................................................. 11
3.1.1.2 Line Control............................................................................................................ 11
3.2 Equipment, Scope of Delivery............................................................................ 13
3.3 Type Label ............................................................................................................ 13
3.4 Assembly.............................................................................................................. 14
3.4.1 Block Diagram........................................................................................................ 14
3.4.2 Front View.............................................................................................................. 15
3.4.3 Status Indicators .................................................................................................... 16
3.4.4 I/O LEDs ................................................................................................................ 16
3.5 Product Data......................................................................................................... 16
4Start-Up................................................................. 17
4.1 Installation and Mounting ................................................................................... 17
4.1.1 Mounting and Removing the Modules ................................................................... 17
4.1.2 Connecting the Digital Inputs................................................................................. 17
4.1.2.1 Surges on Digital Inputs......................................................................................... 19
4.1.3 Mounting the DI 32 01 in Zone 2............................................................................ 20
4.2 Configuration ....................................................................................................... 21
4.2.1 Module Slots .......................................................................................................... 21
4.3 Configuring the Module with SILworX............................................................... 21
4.3.1 Parameters and Error Codes for the Inputs ........................................................... 22
4.3.2 Inputs ..................................................................................................................... 22
4.3.2.1 Module Tab ........................................................................................................... 23
4.3.2.2 DI 32 01: Channels Tab........................................................................................ 24

Table of Contents DI 32 01
Page 4 of 38 HI 800 203 E Rev. 1.00
4.4 Configuring Using ELOP II Factory ....................................................................24
4.4.1 Configuring the Inputs ............................................................................................24
4.4.2 Signals and Error Codes for the Inputs .................................................................. 24
4.4.3 Digital inputs...........................................................................................................25
5Operation .............................................................. 27
5.1 Handling................................................................................................................27
5.2 Diagnosis ..............................................................................................................27
6Maintenance.......................................................... 28
6.1 Faults.....................................................................................................................28
6.2 Maintenance Measures........................................................................................29
6.2.1 Loading the Operating System...............................................................................29
6.2.2 Proof Test...............................................................................................................29
7Decommissioning.................................................. 30
8Transport .............................................................. 31
9Disposal................................................................ 32
Appendix............................................................... 33
Glossary................................................................................................................33
Index of Figures....................................................................................................34
Index of Tables .....................................................................................................35
Index......................................................................................................................36

DI 32 01 1 Introduction
HI 800 203 E Rev. 1.00 Page 5 of 38
1 Introduction
This manual describes the technical characteristics of the module and its use. It also
includes instructions on how to install, start up and replace it.
1.1 Structure and Use of this Manual
The content of this manual is part of the hardware description of the HIMatrix
programmable electronic system.
This manual is organized in the following main chapters:
Introduction
Safety
Product Description
Start-Up
Operation
Maintenance
Decommissioning
Transport
Disposal
This manual distinguishes between the following variants of the HIMatrix system:
Programming tool Processor operating system Communication operating
system
SILworX Version 7 and beyond Version 12 and beyond
ELOP II Factory Versions prior to 7 Versions prior to 12
Table 1: HIMatrix System Variants
The manual distinguishes among the different variants using:
Separated chapters
Tables differentiating among the versions, e.g., version 7 and beyond, or prior to
version 7
iProjects created with ELOP II Factory cannot be edited with SILworX, and vice versa!
iThis manual usually refers to compact controllers and remote I/Os as devices, and to the
plug-in cards of a modular controller as modules.

1 Introduction DI 32 01
Page 6 of 38 HI 800 203 E Rev. 1.00
Additionally, the following documents must be taken into account:
Name Content Document number
HIMatrix System Manual
Compact Systems
Hardware description of the HIMatrix
compact systems
HI 800 141 E
HIMatrix System Manual
Modular System F60
Hardware description of the HIMatrix
modular system
HI 800 191 E
Himatrix Safety Manual Safety functions of the HIMatrix
system
HI 800 023 E
HIMatrix Engineering
Manual
Project planning description for
HIMatrix systems
HI 800 101 E
SILworX Online Help Instructions on how to use SILworX -
ELOP II Factory Online
Help
Instructions on how to use ELOP II
Factory, Ethernet IP protocol,
INTERBUS protocol
-
First Steps
SILworX
Introduction to SILworX using the
HIMax system as an example
HI 801 103 E
First Steps
ELOP II Factory
Introduction to ELOP II Factory HI 800 006 E
Table 2: Additional Relevant Documents
The latest manuals can be downloaded from the HIMA website www.hima.com. The
revision index on the footer can be used to compare the current version of existing manuals
with the Internet edition.
1.2 Target Audience
This document addresses system planners, configuration engineers, programmers of
automation devices and personnel authorized to implement, operate and maintain the
modules and systems. Specialized knowledge of safety-related automation systems is
required.

DI 32 01 1 Introduction
HI 800 203 E Rev. 1.00 Page 7 of 38
1.3 Formatting Conventions
To ensure improved readability and comprehensibility, the following fonts are used in this
document:
Bold: To highlight important parts
Names of buttons, menu functions and tabs that can be clicked and
used in the programming tool.
Italics: For parameters and system variables
Courier Literal user inputs
RUN Operating state are designated by capitals
Chapter 1.2.3 Cross references are hyperlinks even though they are not
particularly marked. When the cursor hovers over a hyperlink, it
changes its shape. Click the hyperlink to jump to the corresponding
position.
Safety notes and operating tips are particularly marked.
1.3.1 Safety Notes
The safety notes are represented as described below.
These notes must absolutely be observed to reduce the risk to a minimum. The content is
structured as follows:
Signal word: danger, warning, caution, notice
Type and source of danger
Consequences arising from the danger
Danger prevention
The signal words have the following meanings:
Danger indicates hazardous situation which, if not avoided, will result in death or serious
injury.
Warning indicates hazardous situation which, if not avoided, could result in death or
serious injury.
Warning indicates hazardous situation which, if not avoided, could result in minor or
modest injury.
Notice indicates a hazardous situation which, if not avoided, could result in property
damage.
NOTE
Type and source of damage!
Damage prevention
SIGNAL WORD
Type and source of danger!
Consequences arising from the danger
Danger prevention

1 Introduction DI 32 01
Page 8 of 38 HI 800 203 E Rev. 1.00
1.3.2 Operating Tips
Additional information is structured as presented in the following example:
iThe text corresponding to the additional information is located here.
Useful tips and tricks appear as follows:
TIP The tip text is located here.

DI 32 01 2 Safety
HI 800 203 E Rev. 1.00 Page 9 of 38
2 Safety
The following safety information, notes and instructions must be strictly observed. The
product may only be used if all guidelines and safety instructions are adhered to.
This product is operated with SELV or PELV. No imminent danger results from the product
itself. The use in Ex-Zone is permitted if additional measures are taken.
2.1 Intended Use
HIMatrix components are designed for assembling safety-related controller systems.
When using the components in the HIMatrix system, comply with the following general
requirements
2.1.1 Environmental Requirements
Requirement type Range of values
Protection class Protection class III in accordance with IEC/EN 61131-2
Ambient temperature 0...+60 °C
Storage temperature -40...+85 °C
Pollution Pollution degree II in accordance with IEC/EN 61131-2
Altitude < 2000 m
Enclosure Standard: IP20
Supply voltage 24 VDC
Table 3: Environmental Requirements
Exposing the HIMax system to environmental conditions other than those specified in this
manual can cause the HIMatrix system to malfunction.
2.1.2 ESD Protective Measures
Only personnel with knowledge of ESD protective measures may modify or extend the
system or replace devices.
NOTE
Device damage due to electrostatic discharge!
When performing the work, make sure that the workspace is free of static and
wear an ESD wrist strap.
If not used, ensure that the device is protected from electrostatic discharge, e.g.,
by storing it in its packaging.

2 Safety DI 32 01
Page 10 of 38 HI 800 203 E Rev. 1.00
2.2 Residual Risk
No imminent danger results from a HIMatrix system itself.
Residual risk may result from:
Faults in the engineering
Faults in the user program
Faults in the wiring
2.3 Safety Precautions
Observe all local safety requirements and use the protective equipment required on site.
2.4 Emergency Information
A HIMatrix system is a part of the safety equipment of a site. If a device or a module fails,
the site adopts the safe state.
In case of emergency, no action that may prevent the HIMatrix systems from operating
safely is permitted.

DI 32 01 3 Product Description
HI 800 203 E Rev. 1.00 Page 11 of 38
3 Product Description
DI 32 01 is a plug-in module with 32 digital inputs for the modular F60 HIMatrix system. The
inputs are galvanically isolated to the I/O BUS.
The module can be inserted in the F60 subrack's slot 3...8 as many times as required. Slots
1 and 2 are reserved for the power supply module and CPU module, respectively.
The module has been certified by the TÜV for safety-related applications up to SIL 3 (IEC
61508, IEC 61511 and IEC 62061), Cat. 4 (EN 954-1) and PL e (EN ISO 13849-1). Further
safety standards, application standards and test standards are specified in the certificate
available on the HIMA website.
3.1 Safety Function
3.1.1 Safety-Related Inputs
The module is equipped with safety-related digital inputs. These inputs are divided in 4
groups of 7 inputs and 1 group of 4 inputs (I29...I32). Refer to Table 9 for more information
on the terminal assignment. Each group is equipped with a common short-circuit-proof
supply LS+.
3.1.1.1 Reaction in the Event of a Fault
If the module detects a fault on a digital input, the user program processes a low level in
accordance with the 'de-energize to trip' principle.
The module activates the FAULT LED.
In addition to the channel signal value, the user program must also consider the
corresponding error code.
The error code allows the user to configure additional fault reactions in the user program.
3.1.1.2 Line Control
Line control is used to detect short-circuits or open-circuits and can be configured for the
DI 32 01 e.g., on EMERGENCY STOP inputs complying with Cat. 4 in accordance with
EN 954-1.
To this end, connect the pulsed outputs TO 1...TO 2 of the system to the digital inputs DI of
the same system as follows (example):

3 Product Description DI 32 01
Page 12 of 38 HI 800 203 E Rev. 1.00
EMERGENCY STOP 1
EMERGENCY STOP 2
EMERGENCY STOP devices in
accordance with EN 60947-5-1 and
EN 60947-5-5
Figure 1: Line Control
The device pulses the pulsed outputs to monitor the wires to the digital inputs. To do so,
configure the Value [BOOL] -> system variable in SILworX or the DO[01].Value system
signal in ELOP II Factory.The variables for the pulsed outputs must begin with channel 1
and reside in direct sequence, one after the other.
If the following faults occur, the FAULT LED located on the front plate of the controller
blinks, the inputs are set to low level and an (evaluable) error code is created:
Cross-circuit between two parallel lines,
Improper connections of two lines (e.g., TO 2 to DI 3),
Earth fault of a line (with earthed ground only),
Open-circuit or open contacts, i.e., including when one of the two EMERGENCY STOP
switches mentioned above has been engaged, the FAULT LED blinks and the error
code is created.
For more information on how to configure line control in the user program, refer to the
HIMatrix Engineering Manual.

DI 32 01 3 Product Description
HI 800 203 E Rev. 1.00 Page 13 of 38
3.2 Equipment, Scope of Delivery
The following list specifies the available components and the corresponding part numbers:
Designation Description Part no.
DI 32 01 Plug-in module with 32 digital inputs, SIL3/Cat.4
configurable with cross circuit monitoring
98 2200114
Table 4: Part Numbers
3.3 Type Label
The type plate contains the following details:
Product name
Bar code (1D or 2D code)
Part no.
Production year
Hardware revision index (HW Rev.)
Firmware revision index (FW Rev.)
Operating voltage
Mark of conformity
Figure 2: Sample Type Label

3 Product Description DI 32 01
Page 14 of 38 HI 800 203 E Rev. 1.00
3.4 Assembly
This chapter describes the layout and function of the plug-in module.
3.4.1 Block Diagram
Test
32 Channels
I/O Bus
Figure 3: Block Diagram

DI 32 01 3 Product Description
HI 800 203 E Rev. 1.00 Page 15 of 38
3.4.2 Front View
DI 32
01
Figure 4: Front View

3 Product Description DI 32 01
Page 16 of 38 HI 800 203 E Rev. 1.00
3.4.3 Status Indicators
LED Color Status Description
On Operating voltage presentRUN Green
Off No operating voltage
On Module faulty or external faults
Reaction as dictated by the diagnosis
ERR Red
Off No module faults and / or no channel faults
Table 5: Status Indicators
3.4.4 I/O LEDs
LED Color Status Description
On The related channel is active (energized).I 1...32 Yellow
Off The related channel is inactive (de-energized).
Table 6: I/O LEDs
3.5 Product Data
General
Operating voltage 24 VDC, -15 %...+20 %, wss ≤15 %,
provided by a power supply unit with safe isolation
in accordance with IEC 61131-2 requirements.
Operating data 3.3 VDC / 0.05 A
24 VDC / 0.2 A
Ambient temperature 0 °C...+60 °C
Storage temperature -40 °C...+85 °C
Space requirement 6 RU, 4 HP
Weight 260 g
Table 7: Product Data
Digital Inputs
Number of inputs 32 (galvanically isolated)
Input voltage
High level
Low level
nom. 24 VDC
10 V...30 V
max. 5 V
Input current
High level
Low level
2 mA at 10 V, 5 mA at 24 V
1.0 mA at 5 V
Switching point typ. 7.5 V
Supply 4 x 20 V / 100 mA (at 24 V), short-circuit-proof
Table 8: Specifications for Digital Inputs

DI 32 01 4 Start-Up
HI 800 203 E Rev. 1.00 Page 17 of 38
4 Start-Up
To start up the controller, it must be mounted, connected and configured in the
programming tool.
4.1 Installation and Mounting
The module is mounted in the subrack of the modular HIMatrix F60 system.
4.1.1 Mounting and Removing the Modules
To mount and remove the modules, the connection cable clamp terminals must be
unplugged.
Additionally, personnel must be protected from electrostatic discharge. For details, refer to
Chapter 2.1.2.
Mounting the Modules
To mount a module into the rack
1. Insert the module as far as it can go – without jamming it – into the two guiding rails
which are located on the upper and lower part of the enclosure.
2. Apply pressure to the upper and lower extremity of the front plate until the module plugs
snap into the backplane socket.
3. Secure the module with the screws located on upper and lower extremity of the front
plate.
The module is mounted.
Removing the Modules
To remove a module from the rack
1. Remove the plugs from the module front plate.
2. Release the locking screws located on the upper and lower extremity of the front plate.
3 Loosen the module using the handle located on the lower part of the front plate and
remove it from the guiding rails.
The module is removed.
4.1.2 Connecting the Digital Inputs
The use of shielded cables is not required, but improves the EMC conditions significantly.
To allow the connection of the clamps to the earth grid of the F60, the diameter of the cable
shielding should not exceed 12 mm.
The inputs are connected using 9-pole connectors with numbered terminals. The terminal
pins on the front plate of the module have the same numbered sequence to avoid improper
connections.
Use the following terminals to connect the inputs:
Terminal Designation Function
01 LS+ Supply for inputs 1...7
02 I1 Digital input 1
03 I2 Digital input 2

4 Start-Up DI 32 01
Page 18 of 38 HI 800 203 E Rev. 1.00
Terminal Designation Function
04 I3 Digital input 3
05 I4 Digital input 4
06 I5 Digital input 5
07 I6 Digital input 6
08 I7 Digital input 7
09 EGND Ground
Terminal Designation Function
10 LS+ Supply for inputs 8...14
11 I8 Digital input 8
12 I9 Digital input 9
13 I10 Digital input 10
14 I11 Digital input 11
15 I12 Digital input 12
16 I13 Digital input 13
17 I14 Digital input 14
18 EGND Ground
Terminal Designation Function
19 LS+ Supply for inputs 15...21
20 I15 Digital input 15
21 I16 Digital input 16
22 I17 Digital input 17
23 I18 Digital input 18
24 I19 Digital input 19
25 I20 Digital input 20
26 I21 Digital input 21
27 EGND Ground
Terminal Designation Function
28 LS+ Supply for inputs 22...28
29 I22 Digital input 22
30 I23 Digital input 23
31 I24 Digital input 24
32 I25 Digital input 25
33 I26 Digital input 26
34 I27 Digital input 27
35 I28 Digital input 28
36 EGND Ground
Terminal Designation Function
37 LS+ Supply for inputs 29...32
38 I29 Digital input 29
39 I30 Digital input 30
40 I31 Digital input 31
41 I32 Digital input 32
42 EGND Ground
43 EGND Ground
44 EGND Ground
45 EGND Ground
Table 9: Terminal Assignment for the Inputs

DI 32 01 4 Start-Up
HI 800 203 E Rev. 1.00 Page 19 of 38
4.1.2.1 Surges on Digital Inputs
Due to the short cycle time of the HIMatrix systems, a surge pulse as described in
EN 61000-4-5 can be read in to the digital inputs as a short-term high level.
The following measures ensure proper operation in environments where surges may occur:
1. Install shielded input wires
2. Activate noise blanking: a signal must be present for at least two cycles before it is
evaluated.
iActivating noise blanking increases the response time of the HIMatrix system!
iThe measures specified above are not necessary if the plant design precludes surges from
occurring within the system.
In particular, the design must include protective measures with respect to overvoltage,
lightning, earth grounding and plant wiring in accordance with the relevant standards and
the instructions specified in the System Manual (HI 800 141 E or HI 800 191 E).

4 Start-Up DI 32 01
Page 20 of 38 HI 800 203 E Rev. 1.00
4.1.3 Mounting the DI 32 01 in Zone 2
(EC Directive 94/9/EC, ATEX)
The device is suitable for mounting in zone 2. Refer to the corresponding declaration of
conformity available on the HIMA website.
When mounting the device, observe the special conditions specified in the following
section.
Special Conditions X
1. Mount the HIMatrix F60 DI 32 01 module in an enclosure that meets the EN 60079-15
requirements and achieves a type of protection of at least IP54, in accordance with
EN 60529. Provide the device with the following label:
Work is only permitted in the de-energized state
Exception:
If a potentially explosive atmosphere has been precluded, work can also performed
when the controller is under voltage
2. The enclosure in use must be able to safely dissipate the generated heat. The power
dissipation of the module DI 32 01 is 7 W at maximum depending on the power supply
voltage.
3. The DI 32 01 module must be supplied with 24 VDC from a power supply unit with safe
isolation. Use power supply units of type PELV or SELV only.
4. Applicable standards:
VDE 0170/0171 Part 16, DIN EN 60079-15: 2004-5
VDE 0165 Part 1, DIN EN 60079-14: 1998-08
Pay particular attention to the following sections:
DIN EN 60079-15:
Chapter 5 Design
Chapter 6 Terminals and cabling
Chapter 7 Air and creeping distances
Chapter 14 Connectors
DIN EN 60079-14:
Chapter 5.2.3 Equipment for use in zone 2
Chapter 9.3 Cabling for zones 1 and 2
Chapter 12.2 Equipment for zones 1 and 2
The controller is additionally equipped with the label represented below:
Figure 5: Label for Ex Conditions