Ohlins YA 468 User manual

Shock absorber for Yamaha R1/(R1M)
YA 468
Mounting Instructions
Note!1
Please note that there can be small differences
between your product and the images in
these instructions.
Note!1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not cause
damage to the product, wipe off the excessive
oil or grease with a cloth.
Note!1
Before you install this product, check the kit
contents. If anything is missing, please contact
an Öhlins dealer.
Warning!⚠
Before you install this product, read the Öhlins
Owner’s manual. This product is an important
part of the vehicle and the vehicle stability.
Kit Contents
Description Part No Pcs
Shock absorber YA 468 1
Sticker memo notes 01180-01 1
Sticker set Öhlins 1
Owner´s manual 07242-07 1

2
1
Put the bike on a stand so that the rear wheel
is off the ground.
2
Remove the rear shock linkage bolt.
3
Remove the lower shock mounting bolt.
4
Remove the front shock linkage frame bolt and
bearing sleeve at the frame so the linkage is
removable.
MOUNTING INSTRUCTIONS
Warning!⚠
We strongly recommend to let an Öhlins dealer
install this product.
Warning!⚠
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note!1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note!1
Before you install this product clean the vehicle.
5
Remove the upper shock mounting bolt.
6
Remove the shock absorber to the left.
Note!1
Adjust the swing arm height with a stand or
similar to make the removal easier.
7
Put the Öhlins shock and linkage in place.
8
Install the shock absorber mounting bolt and
the linkage. Load the suspension slightly
before tightening.
9
Make sure that all bolts are tightened and that
there are no clearance problems when the rear
wheel is moving.
Note!1
The Öhlins shock absorber will also t the R1M
model. Note that when you disconnect the STD
shock absorber an error message will be shown
on the display and you will not be able to enter
the main menu.
4
210
Set system to non-electronic suspension.
Turn ignition off.
Hold gray arrow up button + mode button.
Turn ignition on and wait for display to show menu set
up mode.
Release gray arrow up button + mode button.
Select “meter” with gray arrow up/down button.
Press gray arrow up button + mode button to go to
next menu.
Select 2 for Öhlins electronic suspension, and 1 for
non-electronic suspension.
Turn ignition off.

3
MOUNTING INSTRUCTIONS

Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone [phone]
fax [phone]
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SETUP DATA
Warning!⚠
Before you ride/drive, always make sure that the
setup is according to the recommended setup
data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make
any adjustments. Contact an Öhlins dealer if you
have any questions about setting up.
ADJUSTMENTS
Part no. MI_YA468_0
Issued 2017-10-30
Length 315+6/0 mm
Stroke 58 mm
Rebound 16 clicks
Compression 13 clicks
Spring (part no.) 21041-29
Spring preload 14 mm
Spring rate 90 N/mm
Spring free length 150 mm
Recommended free sag and ride height
R1-R3 32 mm
F1-F3 43 mm
Compression
damping
adjuster
Spring
preload
adjuster
Rebound
damping
adjuster
Length
adjuster