Hoist Fitness RS-1406 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
Note: Both Serial Number and Model Number are Required when Ordering Parts
OWNER'S MANUAL
B07
RS-1406
INNER THIGH
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.

02
04
32
33
34
37
40
41
43
45
46
47
49
50
OWNER'S MANUAL
PAGE 01 RS-1406 ASSEMBLY
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
CONTENTS

OWNER'S MANUAL
PAGE 02RS-1406 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

OWNER'S MANUAL
PAGE 03 RS-1406 ASSEMBLY
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

OWNER'S MANUAL
PAGE 04
RS-1406 ASSEMBLY
FRAME ASSEMBLY

- HAND TIGHTEN ALL OTHER HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (72).
OWNER'S MANUAL
PAGE 05 RS-1406 ASSEMBLY
1
136 5/8" 3470
1
21
72
59
59
80
33
76
60
10
60
81
*ASSEMBLE WEIGHT CAGE FIRST*
REFER TO ROC-IT WEIGHT CAGE MANUAL
FOR ASSEMBLY INSTRUCTIONS.
NOTE:
ENSURE THE USE OF WEIGHT
STACK #6

FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
RS-1406 ASSEMBLY
OWNER'S MANUAL
PAGE 06
75
81
60
9
51
60
21

59
69
59
9
80
80
59
59
69
10
- HAND TIGHTEN HARDWARE.
NOTE:
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 07 RS-1406 ASSEMBLY

FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
RS-1406 ASSEMBLY
OWNER'S MANUAL
PAGE 08
55
55
93
77
93
41
18
10
81

NOTE:
HAND TIGHTENED HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY
FRAME ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
PAGE 09
OWNER'S MANUAL
RS-1406 ASSEMBLY
81
60 81
18
60
6076
60
76
10