Hoist Fitness RPL-5303 User manual

RECORD SERIAL NUMBER HERE
OWNER'S MANUAL
[phone]
[phone]
Customer Service
ADDENDUM
READ THIS FIRST!
CATALOG NUMBER 0608-001
RPL-5303 ADDENDUM
Fax
[phone]
JULY, 2008
Note: Both Serial Number and Model Number are Required when Ordering Parts
THE FOLLOWING PAGES WILL SUPERCEDE THE
EXISTING PAGES IN THE RPL-5303 MANUAL
RPL-5303

36 3/4"
w/o RUBBER FOOT
w/ RUBBER FOOT
37"
MAJOR ADJUSTMENT:
LOOSEN JAM NUTS (26, 27) AND TWIST TIE RODS (20)
IN/OUT TO ADJUST THE PRESS ARM TO THE PROPER
HEIGHT. ONCE THE PROPER HEIGHT IS REACHED AND
THE PRESS ARMS ARE OF EQUAL HEIGHTS, BE SURE
TO RE-TIGHTEN JAMS NUTS.
TWIST THE TIE RODS (20) EITHER
- CLOCKWISE TO DECREASE
PRESS ARM HEIGHT
OR
- COUNTER-CLOCKWISE TO
INCREASE PRESS ARM HEIGHT.
26
27
21
22
20
MACHINE ADJUSTMENT CONTINUED
OWNER'S MANUAL
PAGE 27 RPL-5303 ASSEMBLY

0608 - 002
OWNER'S MANUAL
Customer Service
Fax
[phone]
[phone]
[phone]
Note: Both Serial Number and Model Number are Required when Ordering Parts
RECORD SERIAL NUMBER HERE
CATALOG NUMBER
**WARNING !**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.
RPL-5303
PLATE-LOADED INCLINE CHEST PRESS

OWNER'S MANUAL
PAGE 01 RPL-5303 ASSEMBLY
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
MACHINE ADJUSTMENT......................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
CONTENTS
02
04
26
28
29
30
33
36
37
39
41
42
43
44
45

OWNER'S MANUAL
PAGE 02
RPL-5303 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

OWNER'S MANUAL
PAGE 03 RPL-5303 ASSEMBLY
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

OWNER'S MANUAL
PAGE 04
RPL-5303 ASSEMBLY
FRAME ASSEMBLY

FRAME ASSEMBLY
PAGE 05
OWNER'S MANUAL
- HAND TIGHTEN HARDWARE.
RPL-5303 ASSEMBLY
NOTE:
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
3
49
12
28
14
2
58
74
83
58
50

FRAME ASSEMBLY
OWNER'S MANUAL
- WRENCH TIGHTEN HARDWARE.
RPL-5303 ASSEMBLY
NOTE:
PAGE 06
72
60
60
57
16
48
18
16
48 72
57

57
82
32
70
57
63
12
11
18
OWNER'S MANUAL
- WRENCH TIGHTEN HARDWARE.
FRAME ASSEMBLY
PAGE 07 RPL-5303 ASSEMBLY
NOTE: