Hoist Fitness RS-1407 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
OWNER'S MANUAL
Note: Both Serial Number and Model Number are Required when Ordering Parts
B06
RS-1407
OUTER THIGH
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.

02
04
32
33
34
37
40
41
42
44
45
46
47
48
EXERCISE LOG......................................................................
OWNER'S MANUAL
PAGE 01 RS-1407 ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
CONTENTS

OWNER'S MANUAL
PAGE 02RS-1407 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
SAE Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

OWNER'S MANUAL
PAGE 03 RS-1407 ASSEMBLY
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

OWNER'S MANUAL
PAGE 04
RS-1407 ASSEMBLY
FRAME ASSEMBLY

79
71
59
59
21
33
75
60
60
80
STACK # 6
NOTE:
ENSURE THE USE OF WEIGHT
*ASSEMBLE WEIGHT CAGE FIRST*
REFER TO ROC-IT WEIGHT CAGE MANUAL
FOR ASSEMBLY INSTRUCTIONS.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
NOTE:
- WRENCH TIGHTEN HARDWARE (71).
- HAND TIGHTEN ALL OTHER HARDWARE.
FRAME ASSEMBLY
PAGE 05
OWNER'S MANUAL
RS-1407 ASSEMBLY
1
114 3/16" 2900

80
60
9
51
60
74
21
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
OWNER'S MANUAL
RS-1407 ASSEMBLY PAGE 06

- HAND TIGHTEN HARDWARE.
NOTE:
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 07 RS-1407 ASSEMBLY
9
68
59
59
79
79
59
59
68
15

FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
OWNER'S MANUAL
RS-1407 ASSEMBLY PAGE 08
55
55
76
92
41
18
15
92
80

NOTE:
HAND TIGHTENED HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY
FRAME ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
OWNER'S MANUAL
PAGE 09 RS-1407 ASSEMBLY
18
60 80
80
60
60
75
60
75
15

REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
NOTE:
RS-1407 ASSEMBLY
OWNER'S MANUAL
PAGE 10
59
72
59
54
15
59
79
67
59
79

NOTE:
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
OWNER'S MANUAL
PAGE 11 RS-1407 ASSEMBLY
6
67
59
12
59
79
67
59
59
79
67
59
67
59
59
79
59 79
13
6

57
49
13
14
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
NOTE:
RS-1407 ASSEMBLY
OWNER'S MANUAL
PAGE 12

60
15
93
PROPERLY INSTALLED VIEW
49
73
NOTE:
INSERT SHAFT (49) INTO POCKET ON BASE
FRAME ASSEMBLY (15) AND INSTALL FLAT
WASHER (60), SPLIT LOCK WASHER (93),
AND BOLT (73) BEFORE INSTALLING SPLIT
COLLAR (30).
- WRENCH TIGHTEN HARDWARE.
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
NOTE:
OWNER'S MANUAL
PAGE 13 RS-1407 ASSEMBLY
93
30
64
15
49
13
60
73

FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
RS-1407 ASSEMBLY
OWNER'S MANUAL
PAGE 14
14
44
1
NOTE:
POSITION CABLE (1) THROUGH
QUICK RELEASE (44) IN ORDER
TO SECURE CABLE TO CABLE
PULL ARM (14).
44
14
33
1

RS-1407 ASSEMBLY
OWNER'S MANUAL
PAGE 15
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
NOTE:
RS-1407 ASSEMBLY
OWNER'S MANUAL
PAGE 16
80
17
48
13

NOTE:
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
OWNER'S MANUAL
PAGE 17 RS-1407 ASSEMBLY
96
37
37
37
17
37

49
12
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
NOTE:
RS-1407 ASSEMBLY
OWNER'S MANUAL
PAGE 18

NOTE:
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
- WRENCH TIGHTEN HARDWARE.
OWNER'S MANUAL
PAGE 19 RS-1407 ASSEMBLY
93
60
49
15
73
NOTE:
INSERT SHAFT (49) INTO POCKET ON BASE
FRAME ASSEMBLY (15) AND INSTALL FLAT
WASHER (60), SPLIT LOCK WASHER (93),
AND BOLT (73) BEFORE INSTALLING SPLIT
COLLAR (30).
30
12
64
15
60
93
73
49