Hoist Fitness CF-3753 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
A05
OWNER'S MANUAL
Note: Both Serial Number and Model Number are Required when Ordering Parts
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.
CF-3753
7 DEGREE SMITH

02
04
23
27
28
29
32
33
39
41
42
43
44
45
46
PAGE 01
OWNER'S MANUAL
CF-3753 ASSEMBLY
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
WEIGHT RATIOS....................................................................
CONTENTS

OWNER'S MANUAL
PAGE 02
CF-3753 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
2 People Required For Assembly
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
OWNER'S MANUAL
PAGE 03 CF-3753 ASSEMBLY

OWNER'S MANUAL
PAGE 04
CF-3753 ASSEMBLY
FRAME ASSEMBLY

MAKE SURE DECALS FACE
OUTWARD, AS SHOWN
47
66
64
29
10
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
FRAME ASSEMBLY
OWNER'S MANUAL
PAGE 05 CF-3753 ASSEMBLY

FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
UPRIGHT.
- SOME PARTS HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
CF-3753 ASSEMBLY PAGE 06
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHT (1) THROUGH THE FOLLOWING STEPS
UNTIL ASSEMBLY IS SECURED ON PAGE 10.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.
70
LEFT SIDE SHOWN
60
62
29
1
62
18
MAKE SURE SIDE WITH BOLT
HEADS FACES OUT, AS SHOWN

14
98 1/8" 2492.36
69
PRE-ASSEMBLED
LEFT SIDE SHOWN
69
CABLE MAY COME
69
24
56
63
20
63
24
63
63
14
55
63
20
63
54
1
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
NOTE:
- HAND TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
UPRIGHT.
FRAME ASSEMBLY
CF-3753 ASSEMBLY
OWNER'S MANUAL
PAGE 07
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHT (1) THROUGH THE FOLLOWING STEPS
UNTIL ASSEMBLY IS SECURED.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.

14
CUT-OFF THE ZIP TIE
TO POSITION CABLE
AS SHOWN
1
34
LEFT SIDE SHOWN
81
62
62
70
17
2
1
20
UPRIGHT (1), AS SHOWN
BE SURE TO POSITION
CABLE (14) AROUND PULLEY
AND THROUGH SLOT IN
14
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE
UPRIGHT.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY
OWNER'S MANUAL
CF-3753 ASSEMBLY PAGE 08
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHT (1) THROUGH THE FOLLOWING STEP.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.
IMPORTANT
ONLY HAND TIGHTEN BOLTS (81) AS THEY
WILL BE REMOVED FOR INSTALLATION
OF CROSSMEMBER (80) ON PAGE 10

62
59
11
62
2
2
1
1
LEFT SIDE
RIGHT SIDE
62
70
70
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
OWNER'S MANUAL
PAGE 09 CF-3753 ASSEMBLY
WARNING!
BE SURE TO ALWAYS SUPPORT UPRIGHTS (1) THROUGH THIS STEP.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN SERIOUS INJURY OR DEATH.