Home Accents Holiday TY416-2011 User manual

SKU # 1005 415 840
OMS THD SKU # 1005 269 881
Model # TY416-2011
Thank you!
We appreciate the trust and confidence you have placed in Home Accents
through the purchase of this 7 ft Icicle Shimmer LED Stacked Snowmen.
We strive to continually create quality products designed to enhance your
home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing HomeAccents!
1-877-527-0313
HOMEACCENTSHOLIDAY.COM
ASSEMBLY INSTRUCTIONS
7 ft Icicle Shimmer LED Stacked Snowmen
USEANDCAREGUIDE
PLANNING ASSEMBLY
Carefully remove all the parts from the box and place them on the ground. Many parts
are connected by the lighting string that runs throughout the item. Take special care not
to pull, cut or damage the lighting string. Read the entire manual prior to assembly and
identify all the parts included in the package against the parts list. It is recommended to
assemble parts of the product while laying flat on the ground versus standing the item
up to assemble the parts. If any parts are missing or damaged do not attempt assembly
but contact our customer service center or return to place of purchase with purchase
receipt.
*Assembly of this product may require more than one person.
Pre-Operation
CAUTION:Grasp the plug to insert or remove from the power source.
Do not unplug by pulling on cord.
CAUTION:The lighting string on this product is rated at 14.4 Watts (0.12
Amps). Do not overload. Do not connect to another lighting string, decorative outfit or
other electrical products. Before you use or re-use this product inspect it carefully.
Discard or return to place of purchase with purchase receipt if the product has cuts,
damage, frayed wire insulation on cords, cracks in the socket enclosures, loose
connections, exposed copper wire or other obvious damage.
CareandCleaning
a. Carefully remove the product from wherever it is placed. This helps to avoid any
undue strain or stress on the product connections and wires. If the product is placed
somewhere other than the ground it should be well secured and flat.
b. Carefully disassemble the unit taking caution not to cut any electrical wires.
c. Wipe the unit with a damp cloth and allow the unit to dry before storing.
d. Store the product neatly in a cool, dry location protected from sunlight.
Trouble Shooting
a. Ensure that the floor or surface that the item sits on is flat and level
b. Be sure to plug the item correctly to a wall outlet or a UL Listed Power Cord
c. Ensure all parts are assembled properly per the Instruction Manual
d. If the item does not light check for loose or broken bulbs and connections
e. Do not plug into other electrical items
f. If the item has multiple Light String Cords be sure to plug in all cords
g. Check for Broken or Burned Out Fuse In Plug
Guarantee
What is Covered
The product is intended for residential seasonal use for 90 days per year. This
product is covered by a 90 days limited guarantee due to defects in material and
workmanship. Return the product with purchase receipts to the location of purchase
for refund within 90 days of purchase.
What is Not Covered
This warranty does not cover commercial use, normal wear and tear, products not used in
accordance with directions provided on or with the product, burn out of bulbs or LEDS,
batteries, products that have been subjected to unauthorized repair and/or modification
and damage caused by shipping and improper handling, alterations, misuse, in store
display models or accidents. Questions, problems, missing parts? Before returning to the
store, call HomeAccents Holiday Customer Service 8 a.m.-6 p.m., EST, Monday-Friday
Diagram of Parts
Parts List
Locater Name Qty.
A Hat of Lower Snowman 1
B Halves of Lower
Snowman's Body 2
C Nose of Lower Snowman 1
D Arm of Lower Snowman 2
E Leg & Base Stand of Lower
Snowman 1
F Support Pole 2
G Halves of Middle
Snowman's Body 2
H Nose of Middle Snowman 1
I Arm of Middle Snowman 2
J Leg of Middle Snowman 2
K Halves of Top Snowman's
Body 2
L Nose of Upper Snowman 1
M Arm of Upper Snowman 2
N Leg of Upper Snowman 2
O Scarf 3
Hardware List
Locater Name Qty.
P Ground Stake 8
Q Anchoring String 4
R Plastic Tie 30
S Bolt & Wingnut 4
T Spare Fuse 6
U Spare Bulb 6
A H
F B
U
D
E
I
G
C
K
N
M
J
L
S
Q
OP T
R

A
SSEMBLY
1 Assembling the Support Pole to Base Stand
Insert the first Support Pole (F) [with the tapered end up] through the left
foot of Leg & Base Stand of Lower Snowman (E) and secure to the
connecting rod on the base stand with the built in locking pin.
2 Assembling the Lower Snowman Body to the Base Stand
Place the front portion of Lower Snowman's Body (B) on the center
supporting pole. Insert the two connecting rods on the top of the feet on
the base stand into the matching connecting holes on the bottom of Lower
Snowman then fasten together at the connecting loops the with the Bolt &
Wingnut (S) provided.
3 Assembling the Lower Snowman Body
Insert two connecting rods from the back of the feet on the base stand
into the matching holes at the bottom of the back portion of Lower
Snowman Body.Align the back portion of Lower Snowman Body (B) and
the front portion of Lower Snowman Body (B) with each other then
insert the connecting rods on the Front Side into the connecting holes
on the Back Side and fasten at the connecting loops with Plastic Ties (R).
4 Assembling the Nose to the Lower Snowman Body and
Securing the Body parts
Insert the connecting rods on the Nose (C) into the matching connecting
holes on the face of the Lower Showman (B). Fasten the bottom of back of
Lower Snowman with the base together with the Bolt & Wingnut (S)
provided.
5 Assembling the Arms to Lower Snowman Body
Insert the connecting rods on the Arms (D) into the connecting holes on
the sides of the Body (B) then secure at the connecting loops with the
Plastic Ties (R). (Note: The LeftArm has the Light String attached to it).
6 Assembling the Hat and 2nd Support Pole to Lower
Snowman
Attach the second Support Pole (F) through the Hat (A) of Lower Snowman
then stack it onto the First Support Pole already attached to the Lower
Snowman. Secure the Support Poles with the built in locking pin.
F
E
S
B
E
B
R
S
B
C
R
B
D
F
B
A

A
SSEMBLY
7 Assembling the Hat on Lower Snowman
Insert the connecting rods on the bottom of the Hat of Lower Snowman
(A) into the connecting holes on the top of the Head of Lower Snowman
(B).
8 Assembling the Nose and Body of Middle Snowman
Insert the connecting rods on the Nose of Middle Snowman (H) into the
connecting holes on the Head of Middle Snowman (G). Align the two Halves
of Middle Snowman's Body (G) with each other then insert the connecting
rods on one half into the connecting holes on the other half and fasten
together at the connecting loops with Plastic Ties (R).
9 Assembling the Arms and Legs to Middle Snowman's Body
Insert the connecting rods on each Arm (I) and Leg (J) into the connecting
holes on the Middle Snowman's Body (G) and fasten together at the
connecting loops with Plastic Ties (R).
10 Attaching the Middle Snowman to the Lower Snowman
Set the Middle Snowman thru the Second Supporting Pole. Insert the
connecting rods on the bottom of Middle Snowman (G) body into the
connecting holes on the Hat (A) and Left Hand (D) of Lower Snowman.
11 Assembling the Back of the Upper Snowman and the Pole
Insert the short connecting pole inside the Back Portion of the Upper
Snowman (K) to the top of the stacked Support Pole coming out the
Head of Middle Snowman and secure with the built in locking pin.
12 Assembling the Nose and Body of Upper Snowman
Insert the connecting rods on the Nose of Upper Snowman (L) into the
connecting holes on the Head of Upper Snowman (K). Align the two
Halves of Upper Snowman Body (K) with each other then insert the
connecting rods on one half into the connecting holes on the other half
and secure at the connecting loops with Plastic Ties (R).
B
A
G
H
R
J
I
R
G
G
A D
K L
K R

A
SSEMBLY
13 Assembling the Arms and Legs to Upper Snowman
Insert the connecting rods on each Arm (M) and Leg (N) into the
connecting holes on Upper Snowman Body (K) and fasten together
at the connecting loops with Plastic Ties (R).
14 Assembling the Scarf and Connecting the Lights
Wrap the Scarves (O) around the neck of each Snowman. Connecting
three lighting string (from each Snowman) end-to-end.
15 Assembling the Anchoring Strings and Ground Stakes
Hook the plastic clipped end of each of Anchoring Strings (Q) onto the
matching loop on the Body of the Upper Snowman per the diagram
below. Attach the hooked end of the Ground Stakes (P) thru the free
open looped end of each String (Q) then tightly secure the pointed end
of each Ground Stake into the ground evenly spaced from the Stacked
Snowmen. Place the remaining 4 Ground Stakes over the 4 corners of
the Metal Frame on the Base Stand then firmly into the ground.
R
K
M
N
I
O
Q
P