Home Styles 88 5427 09 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
88 5427 09
Entertainment Stand
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Magnet
2 pcs.
M3x15
Wood Screw
4 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
Pull Handle
2 pcs.
M4x32
Machine Screw
2 pcs.
H.
Shelf
2 pcs.
N.
Foot
4 pcs.
L.
Door
1 pc.
M.
Door
1 pc.
K.
Middle Panel
1 pc.
Spring Washer
8 pcs. (+1 extra)
M6x30
Head Cap Bolt
8 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
A.
Top
1 pc.
B.
Base
1 pc.
E.
Shelf
1 pc.
C.
Front Rail
1 pc.
D.
Back Rail
1 pc.
F.
Back Panel
1 pc.
G.
Back Panel
1 pc.
I.
Side Panel
1 pc.
J.
Side Panel
1 pc.

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
N
N
N
N
B
STEP 1
Place Base (B) upside down on a soft cloth.
Attach Feet (N) to Base (B).
STEP 2
Turn unit over to
its’ upright position.
Attach Side Panel (I) to unit with
Flat Washers, Spring Washers and
Head Cap Bolts. (See Figure 1)
Attach Middle Panel (K)
to unit, then flip the locks.
(See Figures 2 and 3)
Slide Back Panel (G) into position.
I
K
G
Head Cap Bolt
Spring Washer
Flat Washer
Lock
Figure 2 Figure 3
Figure 1

Assembly Instructions 3/6
STEP 3
Place Shelf (E) upside down on a soft cloth.
Attach Magnets to Shelf (E) with Wood Screws into pre-drilled holes.
(See Figure 4)
E
Magnet
Wood Screw
Figure 4
STEP 4
Attach Shelf (E), Front Rail (C)
and Back Rail (D) to unit,
then flip the locks.
Slide Back Panel (F) into position.
D
C
E
F
Lock

Assembly Instructions 4/6
J
STEP 5
Attach Side Panel (J) to unit with
Flat Washers, Spring Washers and
Head Cap Bolts, then flip the locks.
STEP 6
Insert Adjustable Pins into side panels
and middle panel at desired level.
(See Figure 5)
Place Shelves (H) into position.
Attach Doors (L) and (M) by sliding door lift
hinges into side panel lift hinges.
(See Figure 6)
Attach Knobs to Doors (L) and (M)
with Machine Screws. (See Figure 7)
Figure 5
Figure 6 Figure 7
Head Cap Bolt
Spring Washer
Flat Washer
Lock
L
M
HH
Adjustable Pin
Knob
Machine Screw

Assembly Instructions 5/6
Figure 8
STEP 7
Attach Top (A) to unit with Flat Washers, Spring Washers and Head Cap Bolts,
then flip the locks.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 8)
A
Head Cap Bolt
Spring Washer
Flat Washer
Lock

Assembly Instructions 6/6
Hardware List
STEP 8
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 9
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319