Home Styles Closet Wall Hanging Unit 88 5530 772 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Carton 88 5530 771 is also needed for assembly.
IMPORTANT
M3x19
Wood Screw for
Leveler
16 pcs. (+1 extra)
Connector
2 pcs.
Leveler
4 pcs.
Plug
4 pcs. (+1 extra)
Hex Wrench
1 pc.
M3 x1.5 6
Wood Screw for
Rod Support
8 pcs. (+1 extra)
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
88 5530 772
Closet Wall Hanging Unit
H.
Front Rail
1 pc.
O.
Bottom
1 pc.
K.
Side Panel
1 pc.
L.
Side Panel
1 pc.
M.
Back Panel
1 pc.
I.
Rod
2 pcs.
J.
Plinth
1 pc.
G.
Top
1 pc.
N.
Back Panel
1 pc.
Rod Support
4 pcs.
M3x15
Wood Screw for
Connector
8 pcs. (+1 extra)
M3x25
Wood Screw (long)
7 pcs. (+1 extra)

Assembly Instructions 2/8
STEP 1
Attach Rod Supports to Side Panels (C), (D), (K)
and (L) with Wood Screws for Rod Support.
(See Figure 1)
Figure 1
D
L
C
K
Rod Support
Wood Screw for
Rod Support
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
Wood Screw for
Rod Support
Rod Support

Assembly Instructions 3/8
STEP 3
Attach unit to Side Panel (L) with
Wood Screws (long), then flip the
locks.
Attach Back Panels (N) and (M)
to unit, then flip the locks.
Attach Front Rail (H) to unit.
Attach Side Panel (K) to unit
with Wood Screws (long), then
flip the locks.
K
H
O
J
M
Figure 2
STEP 2
PlinthAttach (J) to Bottom (O), then flip the locks. (See Figure 2)
L
Wood Screw (long)
N

Assembly Instructions 4/8
STEP 5
Attach Top (G) to unit with Wood
Screws (long), then flip the locks.
STEP 4
Attach Levelers to bottom of unit
with Wood Screws for Levelers.
(See Figure 3)
Wood Screw (long)
G
Leveler
Wood Screw for Leveler
Figure 3

Assembly Instructions 5/8
STEP 7
Attach Top (A) to unit, then flip
the locks.
A
CE
B
D
F
STEP 6
Attach Back Panels (F) and (E)
to Side Panel (D), then flip the
locks.
Attach Front Rail (B) to Side
Panel (D).
Attach Side Panel (C) to unit,
then flip the locks.

Assembly Instructions 6/8
STEP 8
Place top unit onto base unit, then flip the locks.
Figure 6
Figure 5
STEP 9
Place unit at desired location.
Note: If assembling multiple Closet Wall Units
together, place all units at desired location.
Level the unit(s) by adjusting the adjustable
levelers on the bottom of unit(s). (See Figure 4)
Note: Unit(s) must be level to proceed.
Cover all holes with Plugs. (See Figure 5)
Place Rod ( ) into position. (See Figure 6)I
I
I
Figure 4
Plug

Assembly Instructions 7/8
Hardware List
STEP 10
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
If assembling multiple Closet Wall Units
together, go to and complete Step 11 now,
then return to and complete Step 10.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 7
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Top of unit
Drill 3/8” hole in wall
Pre-drilled hole
at top of unit

Assembly Instructions 8/8
STEP 11
Note: If assembling multiple Closet Wall Units together, complete Step 11.
Attach the top of units together using Connector and Wood Screw for Connectors into the
pre-drilled holes. (See Figure 8)
Return to and complete Step 10.
Figure 8
Wood Screw for Connector
Connector

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319