Home Styles 5053-102 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
5053-102
Seven Tier Shelf
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.
Top
1 pc.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
M6x16
Head Cap Bolt
30 pcs. (+1 extra)
Spring Washer
30 pcs. (+1 extra)
Flat Washer
20 pcs. (+1 extra)
Flat Washer (large)
10 pcs. (+1 extra)
B.
Shelf
4 pcs.
C.
Shelf
1 pc.
D.
Base
1 pc.
E.
Side Frame
1 pc.
F.
Side Frame
1 pc.
G.
Side Frame
1 pc.
H.
Side Frame
1 pc.
I.
Stretcher
3 pcs.
J.
Stretcher
1 pc.
Adjustable Pin
16 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/5
STEP 1
Attach Side Frame (E) to Side Frame (G) with Flat Washers,
Spring Washers and Head Cap Bolts, tightening bolts only halfway.
(See Figure 1)
Attach Stretchers (I) and (J) to unit with Flat Washers, Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
Figure 1
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Head Cap Bolt
Spring Washer
Flat Washer
I
J
E
G
I
I
Head Cap Bolt
Spring Washer
Flat Washer
H
F
STEP 2
Attach Side Frame (F) to Side Frame (H) with
Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.

Assembly Instructions 3/5
STEP 4
Attach Top (A), Shelf (C) and Base (D) with Flat Washers (large), Spring Washers and
Head Cap Bolts, tightening bolts only halfway.
Tighten all bolts.
Head Cap Bolt
Spring Washer
Flat Washer (large)
A
D
C
STEP 3
Attach unit to unit from Step 1 with Flat Washers, Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2 and 3.

Figure 2
Figure 3
STEP 5
Turn unit to its upright position.
Insert Adjustable Pins into unit at desired level. (See Figure 2)
Place Shelves (B) into position.
Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 3)
Note: Unit must be level to work property.
Assembly Instructions /45
Adjustable Pin
B
B
B
B

Assembly Instructions /55
Hardware List
STEP 6
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Machine Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 4)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
M3.5x40
Wall Screw
1 pc. (+1 extra)
Figure 4
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
M4x10
Machine Screw
1 pc. (+1 extra)
Machine Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Drill 3/8” hole in wall
Top of unit
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460