Home Styles 20 05506 0095 User manual

Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Kitchen Cart
20 05506 0095
20 09100 Top carton is also need for assembly.
Refer to later page(s) of these instructions for drawer assembly.
A.
Base
1 pc.
B.
Front Rail
1 pc.
C.
Back Rail
1 pc.
D.
Back Rail
1 pc.
E.
Shelf
4 pcs.
F.
Support
2 pcs.
G.
Side Panel
1 pc.
H.
Middle Panel
1 pc.
I.
Middle Panel
1 pc.
J.
Side Panel
1 pc.
K.
Back Upright
1 pc.
M.
Back Panel
3 pcs.
N.
Door
1 pc.
O.
Door
1 pc.
P.
Drawer
1 pc.
Q.
Drawer
3 pcs.
L.
Back Upright
1 pc.

Assembly Instructions 2/10
Hardware List
Cam Lock Screw
15 pcs. (+1 extra)
Cam Lock
15 pcs. (+2 extra)
Adjustable Pin
16 pcs. (+1 extra)
Hinge
4 pcs.
M3.5x25
Wood Screw (long)
32 pcs. (+1 extra)
M3.5x15
Wood Screw (short)
40 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Locking Caster
2 pcs.
M6x30
Head Cap Bolt
10 pcs. (+1 extra)
M6x20
Head Cap Bolt (short)
20 pcs. (+1 extra)
Non-Locking Caster
2 pcs.
Handle
6 pcs.
Towel Bar
2 pcs.
M4x25
Machine Screw
4 pcs.
M4x35
Machine Screw (long)
8 pcs.
Flat Washer
16 pcs. (+1 extra)
Spring Washer
16 pcs. (+1 extra)

Assembly Instructions 3/10
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Cam Lock Screw
G
J
D
C
STEP 1
Insert Cam Lock Screws into pre-drilled
holes in Back Rails (C), (D), Side Panels (G), (J)
and Back Uprights (K), (L) then tighten.
(See Figure 1)
Figure 1
K
L

Assembly Instructions 4/10
STEP 2
Attach Base (A) to Back Rail (D)
with Cam Locks. (See Figure 2)
A
Cam Lock
D
Figure 2
STEP 3
Attach Back Uprights (K)
and (L) to Back Rail (C).
Attach Middle Panels (H) and (I)
to unit with Cam Locks. H
I
C
K
L
Cam Lock

Assembly Instructions 5/10
STEP 4
Slide Back Panels (M) into position.
Attach unit from Step 2 to unit
with Head Cap Bolts. (See Figure 3)
Figure 3
M
M
M
Head Cap Bolt
B
F
F
STEP 5
Attach Front Rail (B) to unit
with Head Cap Bolts.
Attach Supports (F) to unit
with Cam Locks and
Head Cap Bolts (middle).
Head Cap Bolt
Head Cap Bolt (middle)
Cam Lock

Assembly Instructions 6/10
G
J
STEP 6
Attach Side Panels (G)
and (J) to unit with Cam Locks
and Head Cap Bolts.
Cam Lock
Head Cap Bolt
Figure 4
Flat Washer
Spring Washer
Head Cap Bolt (short)
Locking Caster
Non-Locking Caster
STEP 7
Attach Towel Bars to unit
with Head Cap Bolts (short).
Attach Casters to unit with
Flat Washers, Spring Washers
and Head Cap Bolts (short),
with Locking Casters at front,
tightening bolts only halfway.
(See Figure 4)
Tighten all Head Cap Bolts (short).
Towel Bar
Head Cap Bolt (short)

Assembly Instructions 7/10
STEP 8
Attach Hinges to Doors (N) and (O)
with Wood Screws (short) into
pre-drilled holes, then tighten.
(See Figure 5)
N
O
Wood Screw (short)
Hinge
Figure 5
N
O
E
E
E
E
Figure 6 Figure 7
Handle
Machine Screw
Wood Screw (short)
Hinge
Adjustable Pin
STEP 9
Attach Doors (N) and (O)
to unit with Wood Screws (short)
into pre-drilled holes, then tighten.
(See Figure 6)
Attach Handles to Doors (N)
and (O) with Machine Screws.
(See Figure 7)
Insert Adjustable Pins into
side panels and middle panels
at desired level.
Place Shelves (E) into position.

Part List
P1.
Drawer Front
1 pc.
P2.
Drawer Back
1 pc.
P3.
Drawer Side
1 pc.
P4.
Drawer Side
1 pc.
P5.
Drawer Bottom
1 pc.
Assembly Instructions 8/10
STEP 12
Attach Handle with Machine Screws (long).
Drawer (P)
Roller at back
P1
P2
P3
P4
Wood Screw (long)
Bottom
STEP 10
Attach Drawer Front (P1) and
Drawer Back (P2) to Drawer Side (P3)
with Wood Screws (long).
Attach Drawer Side (P4) to unit
with Wood Screws (long).
STEP 11
Slide Drawer Bottom (P5) into groove.
Attach Drawer Bottom (P5) to
unit with Wood Screws (short).
Machine Screw (long)
Handle
Wood Screw (short)
P5

Q1.
Drawer Front
3 pcs.
P2.
Drawer Back
3 pcs.
P3.
Drawer Side
3 pcs.
P4.
Drawer Side
3 pcs.
P5.
Drawer Bottom
3 pcs.
Assembly Instructions 9/10
Drawer (Q)
Q1
P2
P3
P4
Wood Screw (long)
Bottom
STEP 13
Attach Drawer Front (Q1) and
Drawer Back (P2) to Drawer Side (P3)
with Wood Screws (long).
Attach Drawer Side (P4) to unit
with Wood Screws (long).
Part List
STEP 14
Slide Drawer Bottom (P5) into groove.
Attach Drawer Bottom (P5) to
unit with Wood Screws (short).
STEP 15
Attach Handle with Machine Screws (long).
Machine Screw (long)
Handle
P5
Roller at back
Wood Screw (short)

Assembly Instructions 10/10
Figure 8 Figure 9
Up Front Back
Down
Figure 10
Left
Right
STEP 16
Attach Top (W) to unit with Head Cap Bolts (middle).
Slide Drawers (P) and (Q) into position.
Note: Supports (V) from 20 09100 Top carton are not used in this assembly.
Head Cap Bolt (middle)
STEP 17
If needed, adjust doors up or down by removing the front Wood Screws (short) and
loosening slightly the back Wood Screws (short) from side panel, adjusting doors up
or down and re-installing screws. (See Figure 8).
If needed, adjust doors left to right. (See Figure 9)
If needed, adjust doors front to back. (See Figure 10)
W
P
Q
Q
Q