Home Styles 88 5543 07 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Hardware List
H.
Plinth
1 pc.
88 5543 07
Bermuda
Corner TV Stand
Cam Lock
24 pcs.(+6 extra)
Cam Lock Screw
24 pcs.(+2 extra)
Adjustable Pin
24 pcs.(+1 extra)
Pull Handle
2 pcs.
Machine Screw
2 pcs.
K.
Shelf
2 pcs.
L.
Shelf
4 pcs.
M.
Door
1 pc.
N.
Door
1 pc.
E.
Base
.1 pc
I.
Back Panel
.1 pc
F.
Back Panel
.1 pc
J.
Back Panel
.1 pc
G.
Back Panel
.1 pc
B.
Side Panel
.1 pc
D1.
Middle Panel
.1 pc
C.
Side Panel
1 pc.
Flat Washer
for Wood Screw
13 pcs. (+1 extra )
Wood Screw
for Base and
Back Panel
13 pcs.(+1 extra)
O.
Leg
4 pcs.
Magnet
2 pcs.
Wood Screw
for Magnet
4 pcs.(+1 extra)
Tools recommended for assembly :Level
D2.
Middle Panel
.1 pc
A.
Top
1 pc.

STEP 1
Assembly Instructions 2/4
A
Cam Lock Screw
BC
Insert Cam Lock Screws into
the pre-drilled holes of Top (A),
Side Panel (B) and (C),
Back Panel (I) and (J),
Plinth (H), then tighten.
H
J
I
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Wood Screw
Magnet
Cam Lock Screw
Cam Lock Screw
Attach 2X Magnets to Top (A) by using Wood Screws
in the pre-drilled holes.

H
B
C
G
Figure 1
STEP 3
Attach
.
(see Figure 1)
Attach Plinth (H) to Base (E)
with Cam Locks.
Back Panel (F) and (G)
to unit with Cam Locks.
Attach Side Panel (B) and (C)
to unit with Cam Locks
Assembly Instructions 3/4
D1
E
Flat Washer
Wood Screw
Attach Middle Panel (D1) and (D2)
to Base (E) using Flat Washers
and Wood Screws.
STEP 2
F
D2
E
STEP 4
Attach Legs (O) into the
pre-drilled holes of unit
and tighten.
Cam Lock
O
O
O
O
E

Flat Washer
Wood Screw
I
J
A
Assemble Pull Handles to Door (M) and (N) with Machine Screws. (see Figure 3)
Attach Door (M) and (N) to the side panels, by sliding the door lift hinges into the side panels
lift hinges. (see Figure 4)
To level the unit, adjust the adjustable levelers on the bottom of legs. (see Figure 5)
Place Top (A) onto unit with Cam Locks.
Attach Back Panel (I) and (J)
to the unit with Flat Washers
and Wood Screws.
Figure 4
STEP 6
N
M
L
L
L
K
K
L
Figure 2
Figure 3
Adjustable Pin
Insert Adjustable Pins into side panels and middle panels at the desired level
(see Figure 2), then place Shelves (K) and (L) into position.
Assembly Instructions 4/4
STEP 5
Adjustable Pin
Figure 5