Home Styles Art & Crafts 88 5181 42 User manual

Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Part List
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Cam Lock Screw
12 pcs.(+1 extra)
Cam Lock
12 pcs.
(+1 extra)
Wood Screw (short)
for Drawer Base Part
4 pcs. (+1 extra)
Machine
Screw
1 pc.
Pull Handle
1 pc.
Head Cap Bolt
for Bottom
4 pcs. (+1 extra)
88 5181 42
Art & Crafts Night Stand
J.
Drawer
1 pc.
(Knock-Down Construction, please refer
to the last page of these instructions for
drawer assembly steps)
I.
Frame Leg
2 pcs.
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
E.
Front Rail
2 pcs.
H.
Bottom
1 pc.
G.
Back Panel
1 pc.
F.
Back Rail
2 pcs.
Stopper
1 pc.
Wood Screw
for Bottom
4 pcs. (+1 extra)
Wood Screw (long)
for Drawer Side Part
8 pcs. (+1 extra)
Wood Screw (short)
for Back Panel, Stopper
5 pcs. (+1 extra)
Flat Washer
4 pcs. (+1 extra)
A.
Top
1 pc.
B.
Shelf
1 pc.

Assembly Instructions 2/5
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
Figure 1
A
Figure 2
STEP 2
C
C
Cam Lock Screw
STEP 1
Pull out Shelf (B) from Top (A).
Insert Cam Lock Screws into the pre-drilled holes of Top (A), Side Panel (C) and (D).
(See figure 1)
B
D
Cam Lock
C
D
F
G
E
E
F
Attach Back Rail (F) to Side Panel (C) with
Cam Locks. (See figure 2)
Slide Back Panel (G) to the unit.
Attach Front Rail (E) to unit with
Cam Lock.
Attach Side Panel (D) to unit with Cam
Locks.

Assembly Instructions 3/5
STEP 4
Attach Top (A) to unit with Cam Locks.
Figure 3
H
I
I
STEP 3
Attach Bottom (H) to the unit with Flat Washers, Screws.
(See figure 3)
Attach Frame Leg (I) to the unit with Head Cap Bolts.
(See figure 4)
Figure 4
Flat Washer
Head Cap Bolt
Wood Screw
for Bottom
Cam Lock
Wood Screw
for Bottom
Flat Washer
A

Assembly Instructions 4/5
Figure 5
STEP 5
Slide Shelf (B) back into Top (A) of unit.
Insert Stopper and Wood Screw into the pre-drilled
holes of shelf. (See figure 5)
STEP 6
Insert 4X Wood Screws from the back of the unit,
tighten up all the Wood Screws. (See figure 6)
Slide Drawer (J) into place.
Figure 6
J
Stopper
Wood Screw
for Shelf
Wood Screw
for Back Panel
B
A

N2
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
J2
J3
J4
J5
J5
J1
Figure 3
Figure 4
Insert short wood screws (4X)
into the pre-drilled holes in J5,
tighten screws. (see Figure 3)
Slide J5 into the grooves in J3
and J4. Be sure to push J5 all
the way forward so it meets J1.
(see Figure 2)
STEP 2
STEP 3
STEP 4
Tighten all screws used in drawer assembly.
Assemble Pull Handle with
machine screws. (see Figure 4)
Assembly Instructions 5/5
Part List
J1.
Front Part
1 pc.
J5.
Base Part
1 pc.
J2.
Back Part
1 pc.
J3.
Side Part
1 pc.
J4.
Side Part
1 pc.
Drawer (J)
Attach J1 to J3 and J4, using
a Phillips screwdriver and
long wood screws (4X),
tighten halfway.
Attach J2 to J3 and J4 using
long wood screws (4X),
tighten halfway. (see Figure 1)
J4
J3 J1
J2
Figure 1
STEP 1
N3
J3
J1
J2
J4

Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Wood Screw (short)
for Back Panel
8 pcs. (+1 extra)
Wood Screw (long)
for Drawer Side Part
32 pcs. (+1 extra)
Cam Lock Screw
16 pcs.(+1 extra)
Cam Lock
16 pcs.
(+1 extra)
Wood Screw (short)
for Drawer Base Part
24pcs. (+1 extra)
Machine
Screw
9 pcs.
Pull Handle
9 pcs.
Head Cap Bolt
for Bottom
4 pcs. (+1 extra)
88 5181 41
Art & Crafts Chest
K.
Drawer
1 pc.
(Knock-Down Construction, please refer
to the last page of these instructions for
drawer assembly steps)
J.
Frame Leg
2 pcs.
A.
Top
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
D.
Front Rail
2 pcs.
I.
Back Rail
2 pcs.
F.
Bottom
1 pc.
G.
Back Panel
2 pcs.
H.
Back Piece
1 pc.
L.
Drawer
3 pcs.
(Knock-Down Construction, please refer
to the last page of these instructions for
drawer assembly steps)
E.
Front Rail
2 pcs.
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Tools recommended for assembly :Level

Assembly Instructions 2/6
Figure 1
Cam Lock Screw
Cam Lock Screw
B
A
C
STEP 2
Attach Frame Leg (J) to Bottom (F)
with Head Cap Bolts. (See figure 2)
J
F
F
Head Cap Bolt
Figure 2
STEP 1
Insert Cam Lock Screws into the
pre-drilled holes of Side Panel (B), (C)
Top (A) and Bottom (F)
(See figure 1)
J
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly item must be level to work properly. Use the included adjustable levelers to level.

Assembly Instructions 3/6
STEP 4
Figure 3
D
G
I
B
Attach Side Panel (C) to the unit
with Cam Locks. (See figure 3)
STEP 3
Attach Side Panel (B) to the unit with Cam Locks.
Attach Back Rail (I) to Side Panel (B)
with Cam Locks. (See figure 3)
Slide Back Panel (G) and place Back Piece (H)
into the unit.
Attach Back Rail (I) to the unit with Cam Lock.
Attach Front Rail (D) and (E) to the unit with
Cam Locks.
C
Cam Lock
Cam Lock
E
D
E
G
H
I

Assembly Instructions 4/6
Cam Lock A
L
STEP 5
Attach Top (A) to the unit with Cam Locks.
Figure 4
STEP 7
Slide Drawer (K) and (L) into place.
STEP 6
Insert 8X Wood Screws from the back of the unit,
tighten up all the Wood Screws. (See figure 4)
Wood Screw
for Back Panel
L
K
L
To level the unit, adjust the
adjustable levelers on the
bottom of legs.
Note: Please make sure unit is level before
tightening these screws.

N2
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
K2
K3
K4
K5
K5
K1
Figure 3
Figure 4
Insert short wood screws (6X)
into the pre-drilled holes in K5,
tighten screws. (see Figure 3)
Slide K5 into the grooves in K3
and K4. Be sure to push K5 all
the way forward so it meets K1.
(see Figure 2)
STEP 2
STEP 3
STEP 4
Tighten all screws used in drawer assembly.
Assemble Pull Handle with
machine screws. (see Figure 4)
Assembly Instructions 5/6
Part List
K1.
Front Part
1 pc.
K5.
Base Part
1 pc.
K2.
Back Part
1 pc.
K3.
Side Part
1 pc.
K4.
Side Part
1 pc.
Drawer (K)
Attach K1 to K3 and K4, using
a Phillips screwdriver and
long wood screws (4X),
tighten halfway.
Attach K2 to K3 and K4 using
long wood screws (4X),
tighten halfway. (see Figure 1)
K4
K3 K1
K2
Figure 1
STEP 1
N3
K3
K1
K2
K4