Home Styles 5089-95 User manual

Tool(s) required for assembly: Phillips screwdriver
5089 95-
Kitchen Cart
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
M6x35
Head Cap Bolt
14 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
32 pcs. (+1 extra)
M3.5x13
Wood Screw (short)
24 pcs. (+1 extra)
M4x16
Wood Screw
22 pcs. (+1 extra)
Wood Plug
10 pcs. (+2 extra)
Adjustable Pin
8 pcs. (+1 extra)
Refer to later page(s) of these
instructions for drawer assembly.
U.
Pipe
3 pcs.
T.
Rack Base
1 pc.
O.
Door
1 pc.
P.
Door
1 pc.
R.
Rack Side
1 pc.
S.
Rack Side
1 pc.
N.
Arm
1 pc.
M.
Arm Handle
2 pcs.
K.
Base
1 pc.
G.
Back Upright
2 pcs.
J.
Front Rail
3 pcs.
H.
Back Rail
1 pc.
I.
Front Rail
1 pc.
F.
Back Panel
3 pcs.
D.
Middle Panel
1 pc.
E.
Middle Panel
1 pc.
C.
Side Panel
1 pc.
B.
Side Panel
1 pc.
A.
Top
1 pc.
Cam Lock
4 pcs. (+2 extra)
Cam Lock Screw
4 pcs. (+1 extra)
Handle
6 pcs.
Caster
2 Locking
2 Non-Locking
4 pcs.
Q.
Gate Leg
1 pc.
M4x25
Machine Screw
12 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Part List
Hardware List
W.
Drawer
1 pc.
V.
Drawer
3 pcs.
L.
Shelf
2 pcs.

Assembly Instructions 2/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 2
Attach lower Front Rail (J) to unit.
Attach middle Front Rail (J) to unit.
Attach upper Front Rail (J) to unit.
Slide Back Panels (F) into position.
STEP 1
Attach Side Panel (B) to Base (K) with
Head Cap Bolts. (See Figure 1)
Attach Back Upright (G) to Middle Panel (D),
then attach to unit.
Attach Back Upright (G) to Middle Panel (E),
then attach to unit.
Note: Assemble so Arrow labels
on Back Uprights (G) point
to each other.
Head Cap Bolt
Arrow labels point to each other
Figure 1
DE
K
G
F
G
B
F
J
J
J
F

Assembly Instructions 3/9
STEP 4
Turn unit upside down.
Attach Casters to unit with
Wood Screws into pre-drilled holes,
with Locking Casters at front.
(See Figure 2)
Note: Arrow label indicates front of unit.
Figure 2
STEP 3
Attach Back Rail ( ) andH
Front Rail ( ) to unit withI
Head Cap Bolts.
Note: Arrow label indicates
front of Back Rail ( ).H
Attach Side Panel ( ) toC
unit with Head Cap Bolts.
Arrow label at front
Head Cap Bolt
C
Arrow label at front
Wood Screw
Non-Locking Caster
Locking Caster
H
I

Assembly Instructions 4/9
STEP 5
Turn unit over to its upright position.
Attach Rack Side (R) to unit with Head Cap Bolt. (See Figure 3)
Slide Rack Base (T) and Pipes (U) into Rack Side (R).
Attach Rack Side (S) to unit with Head Cap Bolt.
Attach Arm Handles (M) to unit with Head Cap Bolts. (See Figure 4)
Slide Arm (N) into position.
RM
Figure 4
Figure 3
Head Cap Bolt
U
S
M
T
N
M
R

Assembly Instructions 5/9
STEP 7
Insert Adjustable Pins
into side panels and
middle panels at
desired level.
(See Figure 6)
Place Shelves (L) into
position.
Attach Doors (O) and (P)
by sliding door hinges
into side panel hinges.
(See Figure 7)
Attach Handles to
Doors (O) and (P)
with Machine Screws.
(See Figure 8)
Adjustable Pin Handle
Machine Screw
L
L
O
STEP 6
Attach Gate Leg (Q) to back of unit with
Wood Screws into pre-drilled holes.
(See Figure 5)
Figure 5
Wood Screw
P
Q
Figure 6 Figure 8Figure 7

Assembly Instructions 6/9
STEP 10
Attach Handle with Machine Screws.
V1.
Drawer Front
3 pcs.
V2.
Drawer Back
3 pcs.
V5.
Drawer Bottom
3 pcs.
Wood Screw (short)
Drawer ( )V
V3.
Drawer Side
3 pcs.
V4.
Drawer Side
3 pcs.
STEP 8
Attach Drawer Front ( 1) and DrawerV
Back ( 2) to Drawer Side ( 3)VV
with Wood Screws (long).
Attach Drawer Side ( 4) to unitV
with Wood Screws (long).
Wood Screw (long)
Bottom
STEP 9
Slide Drawer Bottom ( 5) into groove.V
Attach Drawer Bottom ( 5) toV
unit with Wood Screws (short).
Bottom Bottom
V5
Roller at back
Machine Screw
Handle
BottomBottom
V4
V1
V3
V2
Part List

Assembly Instructions 7/9
Part List
STEP 13
Attach Handle with Machine Screws.
W1.
Drawer Front
1 pc.
W2.
Drawer Back
1 pc.
W5.
Drawer Bottom
1 pc.
STEP 11
Attach Drawer Front ( 1) and DrawerW
Back ( 2) to Drawer Side ( 3)WW
with Wood Screws (long).
Attach Drawer Side ( 4) to unitW
with Wood Screws (long).
Drawer ( )W
STEP 12
Slide Drawer Bottom ( 5) into groove.W
Attach Drawer Bottom ( 5) toW
unit with Wood Screws (short).
W3.
Drawer Side
1 pc.
W4.
Drawer Side
1 pc.
Bottom Bottom
Bottom Bottom
Wood Screw (long)
Bottom
W2
W3
W4
Roller at back
W1
Wood Screw (short)
W5
Machine Screw
Handle

Assembly Instructions 8/9
STEP 15
Attach Top (A) to unit with
Cam Locks. (See Figure 10)
Slide Drawers (V)
and (W) into position.
Cam Lock Screw
A
STEP 14
Place Top (A) upside down on
a soft cloth.
Insert Cam Lock Screws into
pre-drilled holes in Top (A),
then tighten. (See Figure 9)
Cam Lock
A
V
V
V
W
Figure 9 Figure 10

Assembly Instructions /99
STEP 16
Cover all holes with Wood Plugs. (See Figure 11)
Figure 11
Wood Plug

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460