Home Styles Bermuda 88 5542 19 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools required for assembly : Phillips screwdriver
88 5542 19
Bermuda
Computer Cabinet
H.
Middle Panel
1 Pc.
K.
Keyboard Tray
1 Pc.
(Knock-Down Construction, please refer to page No. 6/8
of these instructions for steps to assembly keyboard tray.)
L.
Printer Tray
1 Pc.
M.
Shelf
1 Pc.
O.
Door
1 Pc.
P.
Pencil Tray
1 Pc.
Q.
Drawer
1 Pc.
R.
Drawer
1 Pc.
S.
Keyboard
Runner
1 Pc.
T.
Keyboard
Runner
1 Pc.
U.
Front Rail
1 Pc.
N.
Door
1 Pc.
F.
Back Panel
1 Pc.
G.
Back Panel
1 Pc.
A.
Top
1 Pc.
J.
Leg
4 Pcs.
(Knock-Down Construction, please refer to
the last pages of these instructions for drawer
assembly steps.)
I.
Base
1 Pc.
Tools recommended for assembly : Level
B.
Side Panel
1 Pc.
C.
Side Panel
1 Pc.
D.
Stretcher
2 Pcs.
A1.
Wood Support
2 Pcs.
E.
Stretcher
1 Pc.

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools required for assembly : Phillips screwdriver
Hinge
4 Pcs.
Tools recommended for assembly : Level
Hardware List
Machine Screw
2 Pcs.
Cam Lock Screw
18 Pcs. (+1 extra)
Wood Screw (long)
40 Pcs. (+1 extra) 5/8” Wood Screw
for Keyboard Runner
8 Pcs. (+1 extra)
1/2” Wood Screw
for Keyboard Runner
8 Pcs. (+1 extra)
Adjustable Pin
4 Pcs. (+1 extra) Pull
Handle
2 Pcs.
Magnet
2 Pcs.
Wood Screw (short)
22 Pcs. (+1 extra)
Wood Screw
for Magnet
4 Pcs. (+1 extra)
Cam Lock
18 Pcs. (+4 extra) Wood Screw
for Base
2 Pcs. (+1 extra)
Flat Washer
2 Pcs. (+1 extra)
Wood Screw
for Hinge
28 Pcs. (+1 extra)
88 5542 19
Bermuda
Computer Cabinet

Assembly Instructions 3
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
*After assembly, item must be level to work properly.
Use the included adjustable levelers to level.
B
B
B
C
B
A
B
A1
B
A1
Cam Lock Screw
Wood Screw
for Magnet
Magnet
Wood Screw (long)
Wood Screw (long)
Hinge
Wood Screw
for Hinge
Figure 1 Figure 2
Figure 3 B
D
B
H
B
I
B
D
STEP 1
Insert Cam Lock Screws
into the pre-drilled holes of Top (A),
Side Panels (B), (C), Stretchers (D),
Middle Panel (H) and Base (I).
(see Figure 1)
Attach 2X Magnets to Top (A)
with Wood Screws for Magnet
into the pre-drilled holes.
(see Figure 2)
Attach Wood Supports (A1) to
Top (A) and Base (I) with
Wood Screws (long) into the
pre-drilled holes. (see Figure 2)
Attach 4X Hinges to Side Panels (B) and (C)
with Wood Screws for Hinge into the pre-drilled holes.
(see Figure 3)
/9

Assembly Instructions 4
STEP 2
Attach Stretchers (D) and (E) and Front Rail (U)
to Side Panel (B) with Cam Locks.
(see Figure 4)
STEP 3
Slide Back Panels (F) and (G)
into the unit.
Attach Side Panel (C) to unit
with Cam Locks.
B
G
B
F
B
C
B
D
B
U
B
D
B
E
B
B
Cam Lock
Cam Lock Screw
Figure 4
/9

Assembly Instructions 5
B
I
B
H
B
J
B
J
B
J
B
J
B
K
B
A
STEP 4
Attach Middle Panel (H) and Base (I)
to unit with Cam Locks, Wood Screws for
Base and Flat Washers.
Attach Legs (J) into the pre-drilled holes of Base (I) and tighten.
STEP 5
Attach Keyboard (K) to Top (A) with 5/8” Wood Screws for Keyboard Runner.
Flat Washer
Wood Screw for Base
5/8” Wood Screw for
Keyboard Runner
/9

Assembly Instructions 6
B
A
B
LB
QB
O
B
N
B
M
B
R
Figure 5
Figure 6
Figure 7
Figure 8
STEP 7
To level the unit, adjust
the adjustable levelers on the
bottom of the legs.
(see Figure 8)
Insert 12X Wood Screws (short) from
the back of the unit, then tighten up all
the Wood Screws.
Note: Please make sure unit is level before tightening these screws.
STEP 6
Insert Adjustable Pins into side panel
and middle panel at the desired level. (see Figure 5)
Place Shelf (M) into position.
Attach Doors (N) and (O) to the hinges with Wood Screws for Hinge.
(see Figure 6)
Assemble Pull Handles to Doors with Machine Screws.
(see Figure 7)
Slide Printer Tray (L), Drawers (Q) and (R) into position.
Wood Screw (short)
/9

Assembly Instructions 7
Parts List
STEP 1
Attach K3 to K4, using a Phillips
screwdriver and long wood screws
(4X). (see Figure 1)
STEP 2
Attach K1 to K2, using a Phillips
screwdriver and long wood screws
(8X). (see Figure 2)
STEP 3
Attach Keyboard Runners (S) and (T) to unit, using a Phillips
screwdriver and 1/2” wood screws for Keyboard Runner (8X).
(see Figures 3 and 4)
K3.
Back Part
1 Pc.
K1.
Side Part
1 Pc.
K2.
Side Part
1 Pc.
K4.
Base Part
1 Pc.
Kerboard Tray (K)
B
K3
B
K4
Figure 1
Figure 2
Figure 3
Figure 4
B
K1
B
S
B
T
/9

Assembly Instructions 8
Parts List
STEP 1
Attach Q1 to Q3 and Q4, using a
Phillips screw driver and long wood
screws (4X), tighten halfway.
Attach Q2 to Q3 and Q4 using long
wood screws (4X), tighten halfway.
(see Figure 1)
STEP 2
Slide Q5 into the grooves in Q3 and Q4.
Be sure to push Q5 all the way forward
so it meets Q1. (see Figure 2)
STEP 3
Insert short wood screws (4X) into the pre-
drilled holes in Q5, tighten screws.
(see Figure 3)
Tighten all screws used in drawer assembly.
Q1.
Front Part
1 Pc.
Q2.
Back Part
1 Pc.
Q3.
Side Part
1 Pc.
Q4.
Side Part
1 Pc.
Q5.
Base Part
1 Pc.
STEP 4
Place Pencil Tray (P)
into position.
(see Figure 4)
Drawer (Q)
B
Q3
B
Q3
B
Q3
B
Q2
B
Q2
B
Q2
B
Q5
B
Q5
B
Q1
B
Q1
B
Q1
B
Q4
B
Q4
B
Q4
B
P
Figure 1
Figure 3
Figure 4
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
/9

Assembly Instructions 9
Parts List
STEP 1
Attach R1 to R3 and R4, using a
Phillips screw driver and long wood
screws (6X), tighten halfway.
Attach R2 to R3 and R4 using long
wood screws (6X), tighten halfway.
(see Figure 1)
STEP 2
Slide R5 into the grooves in R3 and R4.
Be sure to push R5 all the way forward
so it meets R1. (see Figure 2)
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in R5,
tighten screws. (see Figure 3)
Tighten all screws used in drawer assembly.
R1.
Front Part
1 Pc.
R2.
Back Part
1 Pc.
R3.
Side Part
1 Pc.
R4.
Side Part
1 Pc.
R5.
Base Part
1 Pc.
R6.
Metal Strip
2 Pcs.
STEP 4
Remove the tape
holding the Metal
Strips (R6) in place.
You can adjust
the Metal Strip
for letter size or
legal size file as shown.
(see Figure 4)
Drawer (R)
B
R3
B
R3
B
R3
B
R2
B
R2
B
R2
B
R5
B
R5
B
R1
B
R1
B
R1
B
R4
B
R4
B
R4 B
R6 B
R6
Figure 1
MAKE SURE ROLLER
IS ON THE BACK
Figure 3
Figure 4
Figure 2
/9
Legal Size
Letter Size