Home Styles Buffet 88 5134 64 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
88 5134 64
Buffet
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
D.
Middle Panel
1 pc.
A.
Top
1 pc.
E.
Front Stretcher
1 pc.
G.
Shelf
4 pcs.
H.
Base
1 pc.
I.
Door
1 pc.
J.
Door
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
F.
Back Panel
2 pcs.
M8x32
Wood Screw
for Pull Handle
2 pcs. (+1 extra)
Pull Handle
2 pcs.
M6x35
Head Cap Bolt (short)
6 pcs. (+1 extra)
M4x19
Wood Screw (short)
12 pcs. (+1 extra)
M8x38
Wood Screw (long)
1 pc. (+1 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Magnet
2 pcs.
M3x15
Wood Screw
for Magnet
4 pcs. (+1 extra)
M6x40
Head Cap Bolt (long)
8 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
STEP 1
Attach Back Panels (F) to Side Panel (B)
with Head Cap Bolts (long). (See Figure 1)
Attach Base (H) to unit
with Head Cap Bolt (long).
Attach Side Panel (C) to unit
with Head Cad Bolt (long).
B
C
F
F
H
Figure 1
Head Cap Bolt (long)
STEP 2
Attach Middle Panel (D) to
unit with Head Cap Bolts (short).
D
Head Cap Bolt (short)

Assembly Instructions 3/5
Figure 7
Figure 4
Figure 5
Figure 6
Figure 3
Wood Screw (long)
Magnet
Wood Screw for Magnet
STEP 4
Attach Doors (I) and (J) to unit with Wood Screws (short). (See Figure 4)
Attach Pull Handles to Doors (I) and (J) with Wood Screws for Pull Handle.
(See Figure 5)
Attach Top (A) to unit with Head Cap Bolts (short).
Insert Adjustable Pins into side panels and middle panel at desired level.
(See Figure 6)
Place Shelves (G) into position.
Level unit by adjusting the adjustable levelers on the bottom of legs.
(See Figure 7)
E
STEP 3
Turn unit to it’s upright position.
Attach Magnets to Front Stretcher (E)
with Wood Screws for Magnet. (See Figure 2)
Attach Front Stretcher (E) to unit with
Head Cap Bolts (long) and Wood Screw (long).
(See Figure 3)
Figure 2
A
IJ
G
G
G
G
Adjustable Pin
Head Cap Bolt (short)
Head Cap Bolt (long)

Assembly Instructions 4/5
Hardware List
STEP 5
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 8)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Figure 8
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Drill 3/8” hole in wall
Top of unit

Assembly Instructions 5/5
IMPORTANT
If the magnetic door catches are too strong and difficult to open, the magnetic power can be
reduced and the door made easier to open by doing the following:
Magnet location.
Loosen the Screws
only halfway.
Tighten the Screws. New position.
Rotate
the Magnet
until one Screw
is all the way forward
and the other Screw is all the
way back in the catch slots.
Magnet position.
1
3
56
4
2
Magnet

CARE INSTRUCTIONS
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Advisory Notes
·Do not use power tools above 8 volts to assemble.
·Periodic structural checks of this furniture should be undertaken. Do not use if there are any
doubts about its’ fitness for purpose.
·Exercise care so as to not trap fingers in any of the hinged parts of this furniture.
·Always use on firm level ground, ensuring that all legs remain in contact with the ground.
·Do not stand on a chair or sit or stand on any other item.
·Do not let children play with this furniture.
·This furniture should be stored under cover during periods of adverse weather (wet or cold)
and during winter. Clean and dry thoroughly before storage.
Tannin Exudation
Tannin is a naturally occurring substance which may exude from the surface of some wood species
and may stain the surface of hard areas such as patios or decks. To clean tannin marks use a
proprietary cleaning product or a water-based wood restorer containing oxalic acid. Stains must be
removed within 1-2 days of them occurring. Care should be exercised to follow the manufacturer's
guidelines of the cleaner used and test a small area first to determine its’ effectiveness. This is
especially important on wooden decking areas where the existing surface finish may be lifted due
to the application of the cleaning agent. If decking has become discolored from the cleaning, it
can be restored with a suitable wood finish.
Maintenance
In order to maintain the appearance of the wood, regular coatings of linseed oil must be applied.
The frequency will depend on the weather conditions experienced.
·Refer to the manufacturer’s guidelines of the linseed oil used.
·Apply the linseed oil with a clean cloth, wiping it directly onto the wood surface.
·Treat all surfaces of the furniture. Ensure that any hidden surfaces, such as those exposed
when the furniture is turned upside down, are adequately treated. Care should be given to
wipe the end grain, to all joints and to crevices that may have been caused by damage.
·Let the surface dry out. This can take 4-12 hours depending on weather conditions.
·Repeat the above steps with at least 2 more coats of oil. Extra coats may leave a semi-gloss
sheen once the oil has dried, but excess oil can be wiped off with a clean cloth.
·IMPORTANT: Cloths with linseed oil may be a fire hazard. Immediately after use, saturate all
cloths used for applying linseed oil with water and dispose of safely outside the home.
If left untreated, this furniture will turn a grayish color. Light sanding can restore the original color
after which linseed oil can be applied. Fine surface cracks may occur over time from weathering,
but these won't affect the structural integrity of the furniture.