Home Styles Closet Wall Shelf Unit 20 05520 0762 User manual

Hardware List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
20 05520 0762
Closet Wall Shelf Unit
IMPORTANT
Adjustable Pin
24 pcs. (+1 extra)
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Carton 20 05520 0761 is also needed for assembly.
M3x19
Wood Screw for
Leveler
16 pcs. (+1 extra)
Bracket
2 pcs.
Leveler
4 pcs.
Cam Lock Screw
6 pcs. (+1 extra)
Cam Lock
6 pcs. (+2 extra)
M3x15
Wood Screw for
Bracket
8 pcs. (+1 extra)
M3x25
Wood Screw (long)
4 pcs. (+1 extra)
Part List
J.
Plinth
1 pc.
N.
Back Panel
1 pc.
K.
Bottom
1 pc.
L.
Side Panel
1 pc.
G.
Top
1 pc.
M.
Side Panel
1 pc.
Plug
4 pcs. (+1 extra)
Hex Wrench
1 pc.
H.
Front Rail
1 pc.
B.
Shelf
3 pcs.

Assembly Instructions 2/7
STEP 2
PlinthAttach (J) to Bottom (K),
then flip Lock.
(See Figures 2 and 3)
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Cam Lock Screw
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Side Panels (D), (E), (L) and (M), then tighten.
(See Figure 1)
Figure 1
Cam Lock Screw
Figure 2
K
E
M
J
Figure 3
Lock
L
D
Cam Lock Screw
Cam Lock Screw

Assembly Instructions 3/7
STEP 3
Attach unit to Side Panel (M) with
Cam Locks, then flip Locks.
(See Figure 4)
Attach Back Panel (N) to unit,
then flip Locks.
Attach Front Rails (H) to unit
with Wood Screw (long).
Attach Side Panel (L) to unit with
Cam Locks and Wood Screw (long),
then flip Locks.
STEP 5
Attach Top (G) to unit with
Wood Screws (long),
then flip Locks.
Leveler
Wood Screw (long)
G
Lock
Figure 5
Wood Screw for Leveler
Cam Lock
Wood Screw (long)
N
L
H
M
Figure 4
STEP 4
Attach Levelers to bottom of unit with
Wood Screws for Levelers into
pre-drilled holes (See Figure 5).

Assembly Instructions 4/7
STEP 6
Attach Back Panel (F) to
Side Panel (D), then flip Locks.
Attach Front Rail (C) to unit with
Cam Lock.
Attach Side Panel (E) to unit with
Cam Lock, then flip Locks.
A
D
C
E
STEP 7
Attach Top (A) to unit, then flip Locks.
Lock
F
Cam Lock

Assembly Instructions 5/7
Adjustable Pin
STEP 8
Place top unit onto
base unit, then flip
Locks.
Figure 7
STEP 9
Place unit at desired location.
Note: If assembling multiple Closet Wall Units together,
place all units at desired location.
Level unit(s) by adjusting the adjustable levelers on bottom of unit(s).
(See Figure 6)
Note: Unit(s) must be level to proceed.
Cover all holes with Plugs. (See Figure 7)
Insert Adjustable Pins into side panels at desired level.
Place Shelves (B) into position.
Figure 6
Plug
B
Lock
B
B
B
B
B
Adjustable Pin

Assembly Instructions 6/7
Drill 3/8” hole in wall
Top of unit
Hardware List
STEP 10
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
If assembling multiple Closet Wall Units
together, go to and complete Step 11 now,
then return to and complete Step 10.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 8)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 8
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Pre-drilled hole
at top of unit

Assembly Instructions 7/7
STEP 11
Note: If assembling multiple Closet Wall Units together, complete Step 11.
Attach tops of units together with Brackets and Wood Screws for Brackets into
pre-drilled holes. (See Figure 9)
Return to and complete Step 10.
Wood Screw for Bracket
Bracket
Figure 9

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at: