Home Styles Upholstered Bench 88 5182 26 User manual

PART LIST
88 5182 26
HARDWARE LIST
Upholstered Bench
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
A.
Cushion
1 Pc.
B.
Top
1 Pc.
F.
Base
1 Pc.
Hex Wrench
1 Pc.
Small
Hex Wrench
1 Pc.
Spring Wrench
8 Pcs.(+1 extra)
Flat Wrench
8 Pcs.(+1 extra)
Pull Handle
2 Pcs.
Magnet
2 Pcs.
M3x15
Wood Screw
(for Magnet)
4 Pcs.(+1 extra)
M3x12
Wood Screw
8 Pcs.(+1 extra)
Machine Screw
4 Pcs.(+1 extra)
M3x19
Wood Screw
(long)
8 Pcs.(+1 extra)
One Left Support
One Right Support
2 Pcs.
M6x50
Head Cap Bolt (long)
8 Pcs.(+1 extra)
C.
Side Panel
1 Pc.
E.
Middle Panel
1 Pc.
D.
Side Panel
1 Pc.
G.
Back Panel
1 Pc.
H.
Leg
4 Pcs.
I.
Leg
1 Pc.
J.
Door
1 Pc.
K.
Door
1 Pc.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools recommended for assembly : LevelTools required for assembly : Phillips screwdriver

Assembly Instructions 2/4
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up
the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly.
Use the included adjustable levelers to level.
D
C
Figure 1 Figure 2
G
Lock
STEP 1
Attach Side Panels (C) and (D) to Back Panel (G),
then flip the Locks. (See Figures 1 and 2)
STEP 2
Attach unit and Middle Panel (E) to (F) and flip the Locks.Base
E
F

Assembly Instructions 3/4
STEP 3
Turn unit upside down.
Attach Legs (H) and (I) to unit with Head Cap Bolts,
Spring Washers and Flat Washers. (See Figure 3)
Flat Washer
Spring Washer
Head Cap Bolt
Figure 4
H
H
H
H
I
STEP 4
Place Top (B) upside down on a soft cloth.
Attach Magnets to Top (B) at the pre-drilled holes of Top (B) with Wood Screws (for Magnet).
(See Figure 4)
Figure 3
Wood Screw (for Magnet)
Magnet
B

A
STEP 6
Figure 7
Figure 8
Figure 9
STEP 5
Attach Supports to unit with Wood Screws
into the pre-drilled holes. (See Figures 7 and 8)
Place Cushion (A) into position.
To level the unit, adjust the adjustable levelers
on the bottom of the legs. (See Figure 9)
JK
Figure 5
Figure 6
B
STEP 5
Turn the unit over to its’ upright position.
Attach Top (B) to unit and flip the Locks.
Attach Pull Handles to Doors (J) and (K) with Machine Screws.
(See Figure 5)
Attach Doors (J) and (K) to unit by inserting the door hinges into the
slots in unit and attach with Wood Screws (long). (See Figure 6)
Left Support
Wood Screw (long)
Wood Screw
Right Support
Assembly Instructions 4/4