Home Styles Bermuda 88 5542 951 User manual

Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
For assembly see instructions in carton : 88 5542 952
88 5542 951
Bermuda
Kitchen Cart
A.
Top
1 pc.

Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools required for assembly : Phillips screwdriver
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Hardware List
Part List
Adjustable Pin
24 pcs. (+1 extra)
Caster
Two with lock and
Two without lock
4 pcs.
Small
Key Wrench
1 pc.
Head Cap Bolt
(short)
4 pcs. (+1 extra)
Cam Lock
20 pcs. (+1 extra)
Machine Screw
4 pcs.
Cam Lock Screw
20 pcs. (+1 extra)
Wood Screw
for Caster
16 pcs. (+1 extra)
Also need Parts in carton : 88 5542 951
88 5542 952
Bermuda
Kitchen Cart
F.
Middle Panel
1 pc.
Caster
Key Wrench
1 pc.
B
Handdle
4 pcs.
Wood Screw
(long)
16 pcs. (+2 extra)
Wood Screw
(short)
8pcs. (+1 extra)
(Knock-Down Construction, please refer
to the last page of instruction in carton
88 5542 952 for steps to complete as-
sembly)
p
B.
Top
1 pc.
O.
Back Rail
1 pc.
D.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
P.
Side Bar
2 pcs.
G.
Front Rail
1 pc.
H.
Front Rail
1 pc.
N.
Back Rail
1 pc.
C.
Side Panel
1 pc.
I.
Door
1 pc.
S.
Back Post
1 pc.
J.
Door
1 pc.
K.
Shelf
2 pcs.
L.
Shelf
4 pcs.
Q.
Back Panel
3 pcs.
T.
Drawer
2 pcs.
M.
Divider
1 pc.
R.
Back Post
1 pc.

IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
Assembly Instruction 2 / 5
Figure 1
C
C
STEP 2
Attach 4X Casters to Bottom (B)
with Wood Screws for Caster
with locking casters to the front
and non-locking casters at back.
(see Figure 2)
Insert the Cam Lock Screws into
pre-drilled holes of Bottom (B).
D
D
STEP 1
Insert the Cam Lock Screws into pre-drilled holes of Top (A),
Side Panel (C), and (D). (see Figure 1)
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
A
A
B
B
Locking Casters
Figure 2
Wood Screw
for Caster
Non-Locking Casters

Assembly Instruction 3 / 5
STEP 3
Attach Side Panel (C) to Bottom (B)
with Cam Locks and attach Back Rail
(O) to Side Panel (C) with Cam Lock.
(see Figure 3)
Attach Middle Panel (E) to Back Post
(R) and Middle Panel (F) to
Back Post (S).
Attach middle panel units to unit with
Cam Locks, then slide Back Panels
(Q) into position.
Attach Back Rail (N) to unit with Cam
Locks.
STEP 4
Attach Front Rail (H) to unit
with Cam Lock.
Attach Divider (M) and Front
Rail (G) to unit with Cam Lock.
Attach Side Panel (D) to unit
with Cam Locks.
M
M
C
C
Cam Lock
G
G
Cam Lock
Figure 3
E
E
F
F
N
N
Q
Q
Q
Q
Q
Q
R
R
S
S
B
B
H
H
D
D
Cam Lock
O
O
Cam Lock

Cam Lock
Assembly Instruction 4 / 5
STEP 5
Attach Side Bars (P) to side panels with Head Cap Bolts. (see Figure 4)
Place Top (A) onto the unit and attach with Cam Locks.
Insert Adjustable Pins into side panels and middle panels at the desired level and place
Shelves (K) and (L) into position.
Attach Doors (I) and (J) to side panels by sliding the door lift hinges into the side panel lift
hinges. (see Figure 5)
Assemble Knobs to Door (I) and (J) with Machine Screws. (see Figure 6)
Slide Drawers (S) into position.
Figure 5
A
A
Adjustable Pin
Figure 4 Figure 6
Head Cap Bolt
S
S
S
S
L
L
L
L
L
L
L
L
K
K
K
K
P
P
P
P
I
I
J
J
Cam Lock

Assembly Instruction 5 / 5
STEP 1
Attach T1 to T3 and T4,
using a Phillips screwdriver and
long wood screws (4X), tighten
halfway.
Attach T2 to T3 and T4 using
long wood screws (4X), tighten
halfway. (see Figure 1)
STEP 3
Insert short wood screws (4X)
into the pre-drilled holes in T5
and tighten. (see Figure 3)
STEP 4
Assemble Pull Handle with machine screws. (see
Figure 4)
Tighten all screws used in drawer assembly.
Figure 3
Part List
T5.
Base Part
2 pcs.
T1.
Front Part
2 pcs.
T2.
Back Part
2 pcs.
T3.
Side Part
2 pcs.
T4.
Side Part
2 pcs.
Drawer (T)
MAKE SURE ROLLER
IS ON THE BACK
Figure 4
STEP 2
Slide T5 into the grooves in T3
and T4. Be sure to push T5 all
the way forward so it meets T1.
(see Figure 2)
Figure 2
Figure 1
T5
T5
T3
T3
T2
T2
T1
T1
T1
T1
T3
T3
T4
T4
T2
T2
T4
T4
T1
T1
T4
T4
T5
T5
T2
T2
T3
T3
T
1
.
Fr
o
nt P
a
rt
T2