Home Styles 88 5535 951 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
F.
Side Panel
1 pc.
Casual Attire For Today's Home
Part List
Kitchen Cart
Soft Mahogany Finish
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
88 5535 951
A.
Top
1 pc.
B.
Bottom
1 pc.
I.
Back Stretcher
1 pc.
G.
Shelf
2 pcs.
H.
Shelf
2 pcs.
M.
Door
1 pc.
D.
Side Bar
2 pcs.
E.
Side Panel
1 pc.
C.
Middle Panel
1 pc.
K.
Back Panel
1 pc.
O.
Drawer
1 pc.
(Drawers require assembly.
Please refer to the last page
of these assembly instructions.)
N.
Back Panel
1 pc.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc. Wood Screw (Long)
8 pcs. (+1 extra)
Wood Screw
6 pcs. (+1 extra)
Head Cap Bolt
4pcs. (+1 extra)
Head Cap Bolt (long)
4 pcs. (+1 extra)
Cam Lock Screw
12 pcs.(+1 extra)
Cam Lock
12 pcs.(+1 extra)
Adjustable Pin
16 pcs. (+2 extra)
Hardware List
Caster
two lock
two non-lock
4 pcs.
L.
Rail
1 pc.
J.
Front Stretcher
1 pc.

Assembly Instructions 2/5
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in a safe place as you may need to tighten the Head Cap Bolts in the future.
STEP 2
Cam Lock Screw
Attach Middle Panel (C) to
Rail (L), to Front Stretcher (J)
and Back Stretcher (I) with
Head Cap Bolts (long) and
tighten.
Slide Back Panel (N) to Back
Stretcher (I).
Attach Bottom (B) to unit with
Head Cap Bolts (long) and
tighten.
E
J
A
STEP 1
Put Cam Lock Screws into the
pre-drilled holes of Top (A), Side Panel
(E), (F) and tighten.
F
C
L
I
N
B
Head Cap Bolt (long)
Head Cap Bolt (long)

Assembly Instructions 3/5
Cam Lock
STEP 4
Attach the four Castors to the pre-drilled holes of legs
as shown.
STEP 3
Attach Side Panel (E), (F) to unit with Cam Locks.
Locking Caster
Locking Caster
E
F

Assembly Instructions 4/5
A
K
DD
O
G
G
H
H
F
M
Attach Door (M) to the
Side Panel (F), by sliding
the door lift hinges into the
side panel hinges
(see Figure 2).
Insert Adjustable Pins into
Side panels and Middle
panel at the desired
level.
Slide Shelf (G) and (H)
into place.
Slide the Drawer (O) into position.
Figure 1
Cam Lock
Adjustable Pin
Head Cap Bolt
Figure 2
STEP 5
Slide Back Panel (K) into unit.
Place Top (A) onto the unit, using
Cam Locks.
Attach Side Bar (D) to unit with Head Cap
Bolts (see Figure 1).
STEP 6

Assembly Instructions 5/5
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
T2
T2
T2
T4
T4
T3
T3
T3
T5
T5
T1
T1
Drawer (O)
Part List
Attach O1 to O3 and O4, using
a Phillips screwdriver and
long wood screws (4X),
tighten halfway.
Attach O2 to O3 and O4 using
long wood screws (4X),
tighten halfway. (see Figure 1)
Insert short wood screws (6X)
into the pre-drilled holes in O5,
tighten screws. (see Figure 3)
Slide O5 into the grooves in O3
and O4. Be sure to push O5 all
the way forward so it meets O1.
(see Figure 2)
STEP 1
STEP 2
Tighten all screws used in
drawer assembly.
Figure 3
O2
Back Part
1 pc.
O5.
Base Part
1 pc.
O4.
Side Part
1 pc.
O1.
Front Part
1 pc.
O3.
Side Part
1 pc.
Assembly Instructions 5/5
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
O2
O2
O2
O3
O3
O4
O4
O4
O5
O5
O1
O1
O1
Drawer
Part List
Figure 3
O
T4O3