Home Styles 4513-95 User manual

4513-95
Kitchen Cart
A.
Top
1 pc.
C.
Side Panel
1 pc.
E.
Back Panel
3 pcs.
D.
Middle Panel
1 pc.
H.
Back Rail
1 pc.
F.
Back Upright
2 pcs.
M.
Rack Side
1 pc.
N.
Rack Side
1 pc.
P.
Rack Bar
1 pc.
O.
Rack Base
1 pc.
J.
Base
1 pc.
K.
Arm
2 pcs.
L.
Towel Bar
1 pc.
S.
Shelf
2 pcs.
Q.
Door
1 pc.
R.
Door
1 pc.
I.
Front Rail
2 pcs.
B.
Side Panel
1 pc.
G.
Back Rail
1 pc.
W.
Front Rail
1 pc.
IMPORTANT
Part List
Tool(s) required for assembly: Phillips screwdriver
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
T.
Drawer
3 pcs.
Refer to later page(s) of these
instructions for drawer assembly.

Assembly Instructions 2/9
Hardware List
13
Adjustable Pin
8 pcs. (+1 extra)
09
Machine Screw
5 pcs.
07
Wood Screw for Magnet
4 pcs. (+1 extra)
12
Flat Head Screw
3 pcs. (+1 extra)
11
Wood Screw (short)
24 pcs. (+1 extra)
Hex Wrench
1 pc.
05
Head Cap Bolt for Caster
16 pcs. (+1 extra)
01
Head Cap Bolt
4 pcs. (+1 extra)
02
Head Cap Bolt (long)
4 pcs. (+1 extra)
06
Magnet
2 pcs.
03
Locking Caster
2 pcs.
04
Non-Locking Caster
2 pcs.
Small
Hex Wrench
1 pc.
10
Wood Screw (long)
24 pcs. (+1 extra)
08
Knob
5 pcs.

Assembly Instructions 3/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Assemble Rack Sides (M), (N), Rack Base (O) and Rack Bar (P).
Note: Spice Rack and Towel Bar are interchangeable and may be installed on either side
of the unit.
P
STEP 2
Attach unit to Side Panel (C) with 2 pcs. of .01
01
01
STEP 3
Attach Arms (K) to Side Panel (B) with 2 pcs. of .01
O
N
K
M
C
B
K

Assembly Instructions 4/9
Lock
Figure 1 Figure 2
STEP 4
Attach Back Rail (G)
to Side Panel (C),
then flip Locks.
(See Figures 1 and 2)
Attach Back Uprights (F)
to unit.
Slide Back Panels (E)
into position.
Attach Back Rail (H)
to unit, then flip Lock.
Attach Side Panel (B)
to unit, then flip Locks.
Figure 3
STEP 5
Attach Base (J) to unit with
4 pcs. of . (See Figure 3)02
Then flip Locks.
Note: Arrow label indicates front of Base (J).
E
CE
F
E
G
F
B
H
Arrow label at front
J02
Lock

Assembly Instructions 5/9
Figure 4
STEP 6
Attach 2 pcs. of and 2 pcs. of03 04
to unit with 16 pcs. of .05
Attach at front.03
(See Figure 4)
Note: Arrow label indicates front of unit.
07
06
STEP 7
Attach 2 pcs. of to Front Rail (W)06
by inserting 4 pcs. of into pre-drilled holes,07
then tighten. (See Figure 5)
Figure 5
W
Arrow label at front
05
04
03

Assembly Instructions 6/9
STEP 8
Turn unit over to its
upright position.
Attach Middle Panel (D)
to unit, then flip Locks.
Attach Front Rails (I), (W)
to unit, then flip Locks.
Slide Towel Bar (L) into position.
STEP 9
Attach Doors (Q) and (R) by sliding door hinges
into side panel and middle panel hinges. (See Figure 6)
Attach 2 pcs. of to Doors (Q) and (R)08
with 2 pcs. of . (See Figure 7)09
Attach Top (A) to unit,
then flip Locks.
A
09
08
R
Q
Figure 7
Figure 6
L
W
I
I
D

Part List
T2.
Drawer Back
3 pcs.
T5.
Drawer Bottom
3 pcs.
T1.
Drawer Front
3 pcs.
T3.
Drawer Side
3 pcs.
T4.
Drawer Side
3 pcs.
STEP 12
Attach a with a .08 09
Drawer (T)
Roller at back
Bottom
STEP 10
Attach Drawer Front (T1)
and Drawer Back (T2) to
Drawer Side (T3) with 4 pcs. of .10
Attach Drawer Side (T4) to unit with 4 pcs. of .10
10
11
08
09
STEP 11
Slide Drawer Bottom (T5) into groove.
Attach Drawer Bottom (T5) to unit
with 4 pcs. of .11
Assembly Instructions 7/9
T1
T2
T5
T3
T4

Assembly Instructions 8/9
STEP 13
Close the doors, then adjust
doors gaps look proportional
by move the unit
(See Figure 8)
Open the doors slowly.
Insert 12 pcs. of into11
pre-drilled holes in unit, then tighten.
11
Figure 8
STEP 14
Insert 3 pcs. of into12
pre-drilled holes of Front Rail (W),
then tighten.
12
W

Assembly Instructions 9/9
STEP 15
Insert 8 pcs. of into side panel and middle panel at desired level.13
(See Figure 9)
Place Shelves (S) into position.
Slide Drawers (T) into position. Figure 9
13
S
ST
T
T

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460