Home Styles 88 5252 95 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles ConsumerAssistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
88 5252 95
Kitchen Cart
(Please refer to the last page of these
instructions for drawer assembly steps.)
Tools required for assembly : Phillips screwdriver
Hex Wrench
1 Pc. Cam Lock 16 Pcs. (+1 extra)
M3.5x25
M3.5x16
Knob
1 Pc.
Pull Handle
2 Pcs.
Wood Screw (short)
6 Pcs. (+1 extra)
Wood Screw (long)
8 Pcs. (+1 extra)
Machine Screw
5 Pcs.
M4x25
Head Cap Bolt
6 Pcs. (+1 extra)
M6x40
Cam Lock Screw
16 Pcs. (+1 extra)
Small Hex Wrench
1 Pc.
Wood Screw
for Caster
16 Pcs. (+1 extra)
M4x16
A.
Top
1 Pc.
D.
Side Frame
1 Pc.
E.
Side Frame
1 Pc. F.
Middle Frame
1 Pc.
G.
Middle Frame
1 Pc.
R.
Drawer
1 Pc.
B.
Base
1 Pc.
C.
Back Stretcher
1 Pc.
H.
Back Stretcher
1 Pc. K.
Back Stretcher
1 Pc. L.
Front Stretcher
1 Pc.
J.
Back Stretcher
1 Pc.
I.
Back Panel
1 Pc.
M.
Wine Shelf
10 Pcs.
N.
Shelf
1 Pc. O.
Door
1 Pc.
P.
Arm
2 Pcs.
Q.
RoundArm
1 Pc.
Caster
two lock
two non-lock
4 Pcs.

Assembly Instructions 2
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
STEP 1
Insert Cam Lock Screws into pre-drilled holes of Top (A),
Side Frame (D), (E) and Middle Frame (G).
(see Figure 1)
STEP 2
Attach Casters to Base (B) with
Wood Screws for Caster putting the
Locking Casters in front.
(see “Arrow” sticker indicating front side)
(see Figure 2)
STEP 3
Attach Wine Shelves (M) to Side Frame (D),
Middle Frame (F) and Middle Frame (G).
Attach Front Stretcher (L) and
Back Stretcher (K) to unit with Cam Locks.
(see Figure 3)
D
A
D
F
L
M
M
K
E
G
G
B
Figure 1
Figure 2
Figure 3
/5
Cam Lock Screw
Wood Screw for Caster
Locking Caster
Arrow Sticker Non-Locking Caster
Cam Lock

Assembly Instructions 3
STEP 4
Attach Back Stretcher (C) to unit.
Attach Shelf (N) to unit with Cam Locks.
STEP 5
Attach Back Stretcher (H) and (J) to unit
with Cam Locks.
Slide Back Panel (I) into place.
STEP 6
Attach Side Frame (E) to unit with Cam Locks.
C
H
I
N
E
J
Cam Lock
Cam Lock
Cam Lock
/5

Assembly Instructions 4
Cam Lock
Head Cap Bolt
Head Cap Bolt
Locking Caster
Non-Locking Caster
Arrow Sticker
B
A
STEP 7
With Locking Casters to the front, attach
Base (B) to unit with Head Cap Bolts.
(see Figure 4)
STEP 8
Turn the unit to its upright position.
Attach Arms (P) to unit with
Head Cap Bolts.
Slide Round Arm (Q) into place.
Attach Top (A) to the unit with Cam Locks.
STEP 9
Attach Knob to Door (O) with Machine Screw.
(see Figure 5)
Attach Door (O) by inserting the lower Spring Pin
into the hole until it clicks (see Figure 6) and then
do the same for the upper Spring Pin.
Slide Drawer (R) into place.
Figure 4
Figure 5 Figure 6
PP
R
O
Q
/5

Assembly Instructions 5
Part List
R1.
Front Part
1 Pc.
R2.
Back Part
1 Pc.
R3.
Side Part
1 Pc.
R4.
Side Part
1 Pc.
R5.
Base Part
1 Pc.
Drawer R
B
R1
B
R1
B
R1
B
R2
B
R2
B
R3
B
R3
B
R3
B
R4
B
R4
B
R4
B
R5
B
R5
STEP 1
Attach R1, R2 and R3 using a Phillips
screwdriver and long wood screws (4X),
tighten halfway.
Attach R1, R2 and R4 using
long wood screws (4X), tighten halfway.
(see Figure 1)
MAKE SURE ROLLER
IS ON THE BACK
Figure 1
Figure 2
Figure 3
Figure 4
STEP 2
Slide R5 into grooves in R3 and R4. Be sure
to push R5 all the way forward so it meets R1.
(see Figure 2)
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in R5,
tighten screws. (see Figure 3)
STEP 4
Attach Pulls Handle with Machine Screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
/5