Home Styles 88 4515 95 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver
88 4515 95
Kitchen Cart
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
J.
Front Stretcher
1 pc.
Q.
Shelf
4 pcs.
R.
Door
1 pc.
S.
Door
1 pc.
L.
Tower Bar
1 pc.
K.
Arm
2 pcs.
P.
Rack
1 pc.
O.
Base Rack
1 pc.
M.
Side Rack
1 pc.
N.
Side Rack
1 pc.
A.
Top
1 pc.
U.
Base
1 pc.
T.
Drawer
2 pcs.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
H.
Back Stretcher
1 pc.
I.
Back Stretcher
1 pc.
Refer to the last page(s) of these
instructions for drawer assembly.
G.
Back Upright
2 pcs.
D.
Middle Panel
1 pc.
E.
Middle Panel
1 pc.
F.
Back Panel
3 pcs.
Pull Handle
4 pcs.
Caster
2 lock
2 non-lock
4 pcs.
M3x16
Wood Screw (short)
for Drawer Base Part
and Back Panel
20 pcs. (+1 extra)
Magnet
2 pcs.
M3x16
Wood Screw
for Magnet
4 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
for Drawer Side Part
24 pcs. (+1 extra)
M4x25
Machine Screw
8 pcs.
Adjustable Pin
16 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Wrench
1 pc.
M6x12
Head Cap Bolt
for Caster
16 pcs. (+1 extra)
M6x25
Head Cap Bolt (short)
4 pcs. (+1 extra)
M6x38
Head Cap Bolt (long)
4 pcs. (+1 extra)

STEP 1
Attach Magnets to Top (A) with Wood Screws for Magnet.
(See Figure 1)
STEP 2
Attach Casters underneath Base (U) with Head Cap Bolts for Caster, with Locking Casters on the
front. (See Figure 2)
Note: The ‘Arrow’ sticker indicates the front of Base (U).
Wood Screw for Magnet
Magnet
Head Cap Bolt
for Caster
Locking Caster
Non-Locking Caster
Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
Figure 1
A
U
Figure 2

Assembly Instructions 3/6
Figure 3 Figure 4
Head Cap Bolt
Head Cap Bolt
K
KBC
P
O
M
N
STEP 3
Attach Arms (K) to Side Panel (B) with Head Cap Bolts (short). (See Figure 3)
Assemble Side Racks (M), (N), Base Rack (O) and Rack (P), then attach to Side Panel (C) with
Head Cap Bolts. (See Figure 4)
STEP 4
Attach Back Stretcher (H) to Side Panel (B), then flip the lock.
(See Figures 5 and 6)
Attach Back Uprights (G) to unit, then slide Back Panels (F) into position.
Attach Back Stretcher (I) to unit, then flip the locks.
Attach Side Panel (C) to unit, then flip the locks.
Figure 5
Figure 6
I
B
C
FFF
GG
H

Assembly Instructions 4/6
STEP 5
Attach unit from Step 2 to unit from
Step 4 with Head Cap Bolts (long),
then flip the locks.
Head Cap Bolt (long)
STEP 6
Turn the unit over to its’
upright position.
Insert Wood Screws (short) into
pre-drilled holes of Back Stretchers (H) and (I) and tighten.
Attach Middle Panels (D) and (E) to Front Stretcher (J), then flip the locks.
Attach unit to unit from Step 5, then flip the locks.
Slide Tower Bar (L) into place.
Wood Screw (short)
H
L
J
D
E
I

STEP 7
Attach Pull Handles to Doors (R) and (S) with Machine Screws. (See Figure 7)
Attach Doors (R) and (S) by sliding the door life hinges to side panel lift hinges. (See Figure 8)
Attach Top (A) to unit, then flip the locks.
Insert Adjustable Pins into side panels and middle panels at the desired level, then place
Shelves (Q) into position.
Slide Drawers (T) into position.
Adjustable Pin
Assembly Instructions 5/6
A
Q
R
Q
Q
Q
S
T
T
Figure 7 Figure 8

Part List
Assembly Instructions 6/6
Drawer (T)
STEP 1
Attach Drawer Front (T1) and Drawer
Back (T2) to Drawer Side (T3) with
Wood Screws (long).
Attach Drawer Side (T4) to unit with
Wood Screws (long).
STEP 2
Slide Drawer Bottom (T5) into the grooves
of Drawer Sides (T3) and (T4) until it meets
Drawer Front (T1).
Attach Drawer Bottom (T5) to unit with
Wood Screws (short).
STEP 3
Attach Pull Handle with Machine Screw.
T2.
Drawer Back
2 pcs.
T3.
Drawer Side
2 pcs.
T4.
Drawer Side
2 pcs.
T5.
Drawer Bottom
2 pcs.
T1.
Drawer Front
2 pcs.
Roller at back
T1
T2
T3
T4
T1
T3
T4
T5

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319