Home Styles 88 5522 9502 User manual

88 5522 9502
Kitchen Cart
Tools recommended for assembly : Level
Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools required for assembly : Phillips screwdriver
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
(Please refer to the last page of these
instructions for drawer assembly steps.)
Caster
Two with lock and
Two without lock
4 pcs.
Pull Handle
2 pcs.
Side Bar
2 pcs.
M4x20
Machine Screw
4 pcs.
Spring Washer
8 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
M6x50
Head Cap Bolt (long)
8 pcs. (+1 extra)
M6x30
Head Cap Bolt (short)
6 pcs. (+1 extra)
I.
Drawer
2 pcs.
A.
Top
1 pc.
B.
Shelf
2 pcs.
C.
Front Stretcher
1 pc.
D.
Back Stretcher
1 pc.
E.
Divider
1 pc.
F.
Stretcher
1 pc.
G.
Side Frame
1 pc.
H.
Side Frame
1 pc.
M3.5x25
Wood Screw (long)
16 pcs. (+1 extra)
M3.5x16
Wood Screw (short)
12 pcs. (+1 extra)
Cam Lock Screw
15 pcs. (+1 extra)
Cam Lock
15 pcs. (+1 extra)

Assembly Instructions 2/6
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
* Please make sure unit is level before tightening these screws.
C
D
G
H
Cam Lock Screw
Cam Lock Screw
E
F
Head Cap Bolt (short)
STEP 1
Remove the supports from
Side Frames (G) and (H).
Insert Cam Lock Screws into pre-drilled
holes of Top (A), Front Stretcher (C),
Back Stretcher (D), Side Frames (G)
and (H). (See Figure 1)
Figure 1
STEP 2
Attach Divider (E) to Stretcher (F) with Head Cap Bolts (short).
(See Figure 2)
Figure 2
Support
A
Cam Lock Screw

Assembly Instructions 3/6
D
Cam Lock
STEP 3
Attach Back Stretcher (D) to unit with Cam Locks.
(See Figure 3)
Figure 3
C
Cam Lock
STEP 4
Attach Front Stretcher (C) to unit with Cam Lock.
G
STEP 5
Attach Side Frame (G) to unit with Cam Locks.
Cam Lock

Assembly Instructions 4/6
H
Cam Lock
Spring Washer
Head Cap Bolt (long)
Flat Washer
STEP 7
Attach Side Frame (H) to unit with
Cam Locks, Head Cap Bolts (long),
Spring Washers and Flat Washers.
STEP 6
Attach Shelves (B) to unit with
Head Cap Bolts (long), Spring Washers
and Flat Washers.
(See Figure 4)
B
B
Figure 4
Head Cap Bolt (long)
Spring Washer
Flat Washer

Assembly Instructions 5/6
Locking Caster
Non-Locking Caster
STEP 8
Attach Casters underneath Side Frames (G)
and (H) with Locking Casters to the front.
H
G
STEP 10
Slide Drawers (I) into position.
STEP 9
Turn the unit to its’ upright position.
Attach Side Bars to unit with
Head Cap Bolts (short).
Attach Top (A) to unit with Cam Locks.
II
A
Side Bar
Head Cap Bolt
(short)
Cam Lock

Assembly Instructions 6/6
Part List
Drawer (I)
I1.
Front Part
2 pcs.
I2.
Back Part
2 pcs.
I3.
Side Part
2 pcs.
I4.
Side Part
2 pcs.
I5.
Base Part
2 pcs.
I1
I2
I3
I4
I5
I3
I4
I5
MAKE SURE ROLLER
IS ON THE BACK
Figure 1
I1
STEP 1
Attach I1, I2 and I3 using a screwdriver andPhilips
long Wood Screws (4X), tighten halfway.
Attach I1, I2 and I4 using Wood Screws (4X),long
tighten halfway. (See Figure 1)
Figure 2
STEP 2
Slide I5 into grooves in I3 and I4. Be sure to push
I5 all the way forward so it meet I1.
(See Figure 2)
Figure 3
Figure 4
STEP 3
Insert Wood Screws (6X) into the pre-drilledshort
holes in I5, tighten screws.
(See Figure 3)
STEP 4
Attach Pull Handle with Machine Screws.
(See Figure 4)
Tighten all screws used in drawer assembly.