Honeywell PRO22IC User manual

PRO22IC, PRO22R1, PRO22R2, PRO22OUT, PRO22IN
FEATURES
The PRO-2200 Series family of access modules is controlled
by and connected to the intelligent control module through a
supervised RS-485 bus at 38,400 bps. Hardware interface
configuration options are stored in the intelligent control
module and may be directly controlled via operator
intervention, time schedules or event-based procedures.
The access modules have been designed to allow for a
modular customisable solution. The PRO22R1 provides I/O
support for one card access reader, while the PRO22R2
supports two card access readers. Both interface with the
intelligent control module (PRO22IC). In the event that
communication to the intelligent control module is lost, the
card access readers can be individually configured to allow
entrance based on security needs. This customization allows
for a door to be configured as locked, unlocked, or access
only via valid facility code.
The PRO22OUT interfaces with the intelligent control module
(PRO22IC) providing two dedicated power fail and panel
tamper when tile mounted. Up to 12 or 16, form C, 12 VDC,
2amp, relay output controls depending if the board is rack
or tile-mounted. Relays may be used for elevator control,
status annunciation and for general facility control, such as
door monitoring.
The PRO22IN interfaces with the intelligent control module
(PRO22IC) providing 16 supervised alarm inputs and two
dedicated power fail and panel tamper when tile mounted.
An analog to digital converter samples the input values and
the digitized result is filtered and processed. Filter parameters
are configurable for each input point, resulting in the ability to
specify a custom End- Of-Line (EOL) resistance value,
sensitivity range and timing parameter.
The PRO-2200 Series of access modules is designed to
accommodate various mounting options. Units can be
mounted in a rack configuration (PRO22ENC1, PRO22ENC2
and PRO22ENC5) when space is limited, or in a tile-mount
configuration (PRO22ENC3).
• The PRO22ENC1 is a wall-mounted enclosurerack unit
• The PRO22ENC2 is a 19 inch rack-mounted enclosure
rack unit
• The PRO22ENC5 is a rack unit which fits within a
customers enclosure.
PRO-2200 Series
Access Modules
•Modular design fits a wide variety of
applications
•Up to nine modules, power-supply
and battery can be accommodated
by the PRO22ENC1, PRO22ENC2
and PRO22ENC5 enclosures
•User programmable relay outputs
allow for specific control needs
• User programmable alarm inputs
offer flexible system configuration
and control
• RS-485 communication to all
modules
•Dedicated cabinet tamper and
power monitor inputs
•Analog to digital converter
technology provides digital filtering
and input conditioning
•Supports the choice of normally
open, normally closed, supervised,
and non-supervised circuits
•Supports a wide range of reader
technologies including Wiegand,
Magnetic Stripe, Proximity, and
Keypad
•System off-line modes customizable
per reader include facility code
access, locked (no access), and
unlocked (full access)
•Supports multiple reader and card
formats for maximum flexibility and
security options
•Operating modes include locked,
unlocked, facilit code, cardonly,
card and PIN, card or PIN and PIN
only
•Any combination of 8 I/O or reader
modules may be connected to the
PRO22IC RS-485 ports
•Alarm circuit type – normally open,
normally closed, non-supervised,
supervised (with correct EOL). Meets
requirements for UL294 and CUL
•Any combination of 8 I/0 or readers
modules may be connected to the
PRO221C RS-485 ports. 4,000 feet
/1,250 meters total bus length per
port

PRO22IC, PRO22R1, PRO22R2, PRO22OUT, PRO22IN
PRO-2200 Series Access Modules
CONFIGURATION
• Anti-passback support
Anti-passback support – free pass and exempt flags, last
area accessed, last reader accessed and time/date of last
access
• Modular Hardware
Modular hardware architecture provides flexibility and
expansion capabilities
• Database
Large, local controller database allows access control
decisions to be made by controller in real time without the
need to communicate to the server
• Scalable
Scalable architecture ensures optimal performance with a
seamless upgrade path to accommodate futuregrowth
beyond its initial installation
• Alarm Inputs
Four-state alarm input circuits - normally opened, normally
closed, non-supervised, supervised (w/EOL)
•Mounting Options
Rack or tile mounting options available
• Programmable Sensitivity
Alarm conditioning with programmable sensitivity and hold
time
• ADA Compliant
ADA compliant allowing expanded door times selectable per
reader
•Multiple Reader States
Selectable reader states include card and PIN, card or PIN,
card only, or PIN only
• Auto Switching
Auto switching power supply allows 110 / 220 operation with
PROENC1
•Customisable Modes
System off-line modes customizable per reader include facility
code access, locked (no access), and unlocked (full-access)
• Multiple Reader Formats
Supports multiple reader and card formats for maximum
flexibility and security options
BENEFITS
2www.honeywell.com/security/uk

SPECIFICATIONS
3
www.honeywell.com/security/uk
PRO-2200 Series Single Reader
Modules (PRO22R1)
Module Specifications:
•1Reader port - 12 VDC at 50 mA,
clock / data or data0 / data1
•Keypad multiplexed with card data
•Two-wire or one-wire bi-color LED
support
•Buzzer support only with one-wire
LED control
•2supervised, general purpose alarm
inputs with programmable circuit type
•1dedicated alarm input for tamper
detection
•1general purpose output relay,
form-C, 5A 28 VDC
•1general purpose output relay,
form-C, 1A 28 VDC
•To be used only with the PRO22ENC4
enclosure
Alarm Input Properties:
•Inputs may be assigned to door
related functions or general purpose
I/O
•Circuit type – normally open, normally
closed, non-supervised, supervised
(with standard 1K or custom end-of
line resistance 200-10K)
•Line conditioning – programmable
sensitivity and hold time
Output Control Properties:
•Outputs may be assigned to door
related functions or general purpose
I/O
• The 5A relay(s) are rated to handle
the inductive loads of door locking
devices
• The 1A relay is rated to handle dry
circuit logic
•Configurable as standard (energize to
activate) or fail-safe (de-energize to
activate)
•Pulse control – single pulse (up to 24
hours) or repeating pulse (on/off in
0.1 second increments, up to 255
times)
PW-Series Dual Reader Module
(PRO22R2)
Module Specifications:
•2Reader ports - 12 VDC at 50 mA,
clock/data or data0/data1
•Keypad multiplexed with card data
•Two-wire or one-wire bi-color LED
support
•Buzzer support only with one-wire
LED control
•8supervised, general purpose alarm
inputs with programmable circuit type
(only 6 available when using
PRO22ENC1, PRO22ENC2 and
PRO22ENC5 enclosures)
•2dedicated alarm inputs for tamper
detection and power loss
•2general purpose output relay,
form-C, 5A 28 VDC
•4general purpose output relay,
form-C, 2A 28 VDC (only 2 available
when using PRO22ENC1,
PRO22ENC2 and PRO22ENC5
enclosures)
Alarm Input Properties:
•Inputs may be assigned to door
related functions or general purpose
I/O
•Circuit type – normally open, normally
closed, non-supervised, supervised
(with standard 1K or custom end-of
line resistance 200-10K)
•Line conditioning – programmable
sensitivity and hold time
Output Control Properties:
•Outputs may be assigned to door
related functions or general purpose
I/O
•The 5A relay(s) arerated to handle
the inductive loads of door locking
devices
•The 1A relay is rated to handle dry
circuit logic
•Configurable as standard(energize to
activate) or fail-safe (de-energize to
activate)
•Pulse control – single pulse (up to 24
hours) or repeating pulse (on/off in
0.1 second increments, up to 255
times)
PRO-2200 Series Sixteen Relay
Output Module (PRO22OUT)
Module Specifications:
• 2 dedicated alarm inputs for tamper
detection and power loss (tile-
mounted only)
•12 general purpose output relays,
form C, 2A 30 VDC (16 are available
when using PRO22ENC3 tile-
mounted enclosure)
Output Control Properties:
•All 16-relay outputs in the tile-mount
configuration (12" rack-mount) are
available for general purpose I/O
•The 2A relays are rated to handle dry
circuit logic
•Pulse control – single pulse (up to 24
hours) or repeating pulse (on/off in
0.1 second increments, up to 255
times)
•Configurable as standard(energize
to activate) or failsafe (de-energize to
activate)
PRO-Series Sixteen Alarm Input
Module (PRO22IN)
Module Specifications:
•2dedicated alarm inputs for tamper
detection and power loss (tile-
mounted only)
•16 general purpose inputs with
programmable circuit type
•2general purpose, form C, 2A 30
VDC relays (only one available when
using PRO22ENC1, PRO22ENC2
and PRO22ENC5)
Alarm Input Properties:
•All 16 inputs may be assigned to
door related functions or general
purpose I/O
•Circuit type – normally open,
normally closed, nonsupervised,
supervised (with correct EOL)
•Line conditioning – programmable
sensitivity and hold time
Output Control Properties:
•Both relay outputs are available for
general purpose I/O and rated to
handle dry circuit logic
•Pulse control – single pulse (up to 24
hours) or repeating pulse (on/off in
0.1 second increments, up to 255
times)
COMMUNICATION SPECIFICATIONS
Module Specifications:
Communication Features:
•RS-485 port, 4000 feet / 1,250 meters
total bus length
•Standard speed is 38.4 KBps
PRO-2200 Access Modules (PRO22R1) (PRO22R2) (PRO22OUT) (PRO22IN)

PRO-2200 Series Access Modules
ORDERING
HAS-PRO2200M-01-EN(0807)DS-LD
August 2007
©2007 Honeywell International, Inc.
Honeywell Access Systems UK
Charles Avenue
Burgess Hill
West Sussex.
RH15 9UF
01444 251180
01444 871074
www.honeywell.com/security/uk
For more information: www.honeywell.com/security/uk
Order # Description
PW-2200 Controllers
PRO22IC PRO-2200 Intelligent Controller
PRO22R1 PRO-2200 Single Reader Module
PRO22R2 PRO-2200 Dual Reader Module
PRO22OUT PRO-2200 Sixteen Relay Output Module
PRO22IN PRO-2200 Sixteen Alarm Input Module
PRO22EN PRO-2200 Network Interface Module
PRO-Series Enclosures
PRO22ENC1 (Wall-mount) Capacity: Nine modules. Power supply and battery not included
PRO22ENC2 (19" Rack-mount) Capacity: Nine modules. Power supply and battery not included
PRO22ENC3 (Tile-mount) Capacity: Two modules. Power supply and battery included
PRO22ENC4 (Tile-mount) Capacity: One module (PRO22R1 only). Power supply and battery included
PRO22ENC5 (Cage only for custom enclosures) Capacity: Nine modules. Power supply and battery not included
Optional Accessories
PRO22DCC Daisy Chain cable required for PRO22ENC1, PRO22ENC2 and PRO22ENC5
PRO22E1PS 4-Amp rack-mounted power supply with battery backup required for PRO22ENC1, PRO22ENC2 and PRO22ENC5
Hardwired Kits
PRO22E1IC Includes: PRO22ENC1, PRO22IC, PRO22E1PS, PRO22BAT1 and PRO22DCC
PRO22E2IC Includes: PRO22ENC2, PRO22IC, PRO22E1PS, PRO22BAT1 and PRO22DCC
Network Kits
PRO22E1EN Includes: PRO22ENC1, PRO22IC, PRO22EN, PRO22E1PS, PRO22BAT1 and PRO22DCC
PRO22E2EN Includes: PRO22ENC2, PRO22IC, PRO22EN, PRO22E1PS, PRO22BAT1 and PRO22DCC
COMMON SPECIFICATIONS
Dimensions:
• Board: 9.0" H x 5.5" W x 1.0" D / 228.6 mm H x
139.7 mm W x 25.4 mm D
• PRO22ENC1: 13.9" H x 17" W x 9" D / 353 mm H x 431.8
mm W x 228.6 mm D
• PRO22ENC2: 13.9" H x 18.9" W x 9" D / 353 mm H x
480.06 mm W x 228.6 mm D
• PRO22ENC3: 14" H x 16" W x 4" D / 355.6 mm H x 406.4
mm W x 102 mm D
•PRO22ENC4: 8.37" H x 7.63" W x 7.63 D / 212.8 mm H x
194 mm W x 194 mm D
• PRO22ENC5: 9.35" H x 16.85" W x 5.6" D / 237.4 mm H
x427.9 mm W x 142.2 mm D
Enclosures:
• PRO22ENC1 (Wall-mount) Capacity:
- Nine modules. Power supply and battery not included
• PRO22ENC2 (19" Rack-mount) Capacity:
- Nine modules. Power supply and battery not included
• PRO22ENC3 (Tile-mount) Capacity:
- Two modules. Power supply and battery included
• PRO22ENC4 (Tile-mount) Capacity:
- One module (PRO22R1 only) Power supply and battery
included
• PRO22ENC5 (Cage only for custom enclosures) Capacity:
-Nine modules. Power supply and battery not included
Environment:
• Temperature: 0 to 70° C operational: -55 to 85° C storage
• Humidity: 0 to 95% RHNC
Wire Requirements:
• Power - twisted pair, 18 AWG
• RS-485 - 24 AWG, 4,000 ft. / 1,200 m max, two twisted
pairs with shield (120W, 23pF, Belden 9842 or equiv.)
•RS-232 - 24 AWG, 25 ft. / 7.6 m max.
• Alarm input - twisted pair, 30 ohms max.