Honeywell Ademco 6160CR-2 Assembly instructions

K3590-2CF 9/08 Rev. B
ADEMCO 6160CR
ADEMCO 6160CRADEMCO 6160CR
ADEMCO 6160CR-
--
-2
22
2
Commercial Alpha Keypad
Commercial Alpha KeypadCommercial Alpha Keypad
Commercial Alpha Keypad
INSTALLATION AND SETUP GUIDE
Keypad Features
•Programmable function keys
•Built-in sounder
•ARMED, READY, POWER, FIRE ALARM, SILENCED,
SUPERVISORY, TROUBLE LEDs (see note 1)
•RED keypad for Commercial Fire applications
•Supervised by control panel (required for Commercial Fire
installations)
Supported Control Panels
•VISTA-32FB (see note 2)
•VISTA-128FBP (see note 2)
•VISTA-250FBP (see note 2)
Notes: 1. Trouble and Supervisory LEDs are supported only in the panels listed above.
2. Keypad address may be set to address 00 through 30 to operate with these controls (see control's instructions for
details).
GENERAL INFORMATION
The 6160CR-2 is an addressable remote keypad intended for
use in commercial applications with Honeywell control panels
listed above. The 6160CR-2’s address is set locally, via the
keypad’s keys (see note 2, above). The keys are continuously
backlit for convenience. The LCD display is backlit only when
a key is depressed, or when the system is in alarm or trouble
condition.
Note: On some controls, the LCD may be programmed to
remain on at all times (see control’s instructions for details).
KEYPAD LED INDICATIONS
The keypad’s LEDs will light under the following conditions:
ARMED (Red) ON
OFF
System is Armed
System is Disarmed
READY (Green) ON
OFF
System is Ready
System is Not Ready
POWER (Green) ON
OFF
AC power is O.K.
AC power is removed
FIRE ALARM
(Red)
ON
OFF
Fire Alarm has occurred
Normal
SILENCED
(Yellow)
ON
OFF
Fire Alarm has been silenced
Normal
SUPERVISORY
(Yellow)
ON
OFF
Supervisory condition exists
(see control’s instructions for
details)
Normal
TROUBLE
(Yellow)
ON
OFF
Trouble condition exists
(see
control’s instructions for details)
Normal
SPECIAL FUNCTION KEYS
The keypad also features programmable function keys labeled
A, B, and C. These keys may be programmed to initiate panic
or emergency alarms. Refer to the individual control panel’s
instructions for details.)
These keys must be held down for at least 2 seconds to
initiate the assigned function.
WIRING AND INSTALLATION
The keypad may be surface-mounted directly to a dry wall or
to a single- or double-gang electrical box. If this is the primary
Fire Keypad, connect to Keypad Port 2, wire in conduit, and
mount within 20 ft. of the control.
1. Detach the case back by pushing up into one of the two slots
at the bottom of the keypad with the blade of a small
screwdriver (this will push in the release tab), then pull
that side of the case back away. Repeat for the other side.
Refer to Figure 1 for location of the case back release tabs.
2. Route wiring through the large rectangular opening in the
case back.
3. Mount the case back to the wall or electrical box.
4. Wire directly from the keypad’s terminal block (see Figure
2) to the terminal block on the control panel (see control’s
Summary of Connections label for correct terminal
connections).
NOTE: No more than one wire per terminal may be
connected. If daisy-chained configuration is required, pig-
tail wires together so that only one wire is terminated
under the screw. Use 16-24 AWG wire only!
TABLE 1 - Wiring Connections
Keypad Control Panel Wire Color
▼Y Data Out Yellow
+ + Aux. Pwr Red
– – Aux Pwr (GND) Black
▲GData In Green
5. Reattach the keypad to its case back. Attach the top of
the keypad first, and then press the bottom section down
until it snaps into place securely.
6160CR-006-V2
A
B
C
D
ARMED
POWER
FIRE TROUBLE
FIRE SUPERVISORY
READY
SILENCED
FIRE ALARM
Figure 1 – Removing the Case Back

6160CR-004-V1
+
+
+
+
RED
BLACK
+
+
+
+
YG
+
Figure 2 – 6160CR-2 Wiring Details
SETTING THE KEYPAD ADDRESS
The keypad address must be set according to the control
panel being used (refer to the individual control panel’s
instructions for details). Available addresses are from 00
through 30. The keypad is shipped with a default address
of 31 (non-addressable mode). To change the address, do
the following:
1. Enter keypad address mode:
Power up the keypad. Within 60 seconds of power-up,
press and hold down the [1] and [3] keys together for 3-
seconds. The current address will be displayed and the
cursor will be under the “tens” digit (31).
Notes:
•If the system has been powered up for more than 60
seconds, you must power the keypad down, and then
power it up again in order to change the keypad’s
address.
•The keypad will not enter the address mode if the system
is in the program mode.
•If 10 seconds have passed with no key entry, the keypad
automatically exits the address mode.
Set the desired address:
Enter the desired address. For example, for address 12,
enter 1, then 2. Display shows (12).
2. Exit the address mode:
Press the “star” key (✻)to save the displayed address
and exit the address mode. The current address may be
viewed at any time by pressing and holding [1] and [3]
keys together.
KEYPAD LABELS
Function key labels: A set of adhesive-backed labels
with some typical function symbols (e.g., police,
emergency, etc.) is provided. These labels come in four
colors (red, blue, green, and white) and may be placed on
the appropriate function keys (A, B, or C) for ease of
identifying the individual key’s function (as determined by
the control panel’s capability and programming).
OPERATING THE KEYPAD
For operating instructions, see the User Guide for the
control panel with which this keypad is used.
SPECIFICATIONS
Physical: 5.25” H x 7.437” W x 1.312” D
Display: Alphanumeric, 32-character (2 lines x 16
characters), LCD back-lit
Sounder: High-quality speaker
Electrical: Voltage: +12VDC (from power-limited
source)
Current: 45mA standby;
160mA in alarm (sounder, back
light and LEDs on)
NFPA-72 Compliant
FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM, REFER TO THE INSTALLATION AND
SETUP GUIDE FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED.
ÊK3590-2CF2Š
K3590-2CF 9/08 Rev. B
2 Corporate Center Drive, Suite 100
P.O. Box 9040
Melville, NY 11747
Copyright © 2007 Honeywell International Inc.
www.security.honeywell.com