Honeywell Ademco 6460S Assembly instructions

800-03612 1/09 Rev. B
ADEMCO
ADEMCOADEMCO
ADEMCO 6460S
6460S6460S
6460S/6460
W
/6460
W
/6460
W
/6460
W
REMOTE KEYPAD
REMOTE KEYPADREMOTE KEYPAD
REMOTE KEYPAD
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The ADEMCO 6460S (silver) and 6460W (white) are
addressable Remote Keypads designed for use with
Honeywell's ADEMCO series control panels. Addresses are
set via the keypad keys.
The keys on the keypad are continuously backlit for
convenience.
NOTE: If supported, the ADEMCO 6460S and 6460W
keypads are supervised by control panel. Supervision must
be enabled for commercial fire installations.
KEYPAD DISPLAYS AND LEDS
The ADEMCO 6460S and 6460W keypads have the
following display features:
•2-line Alpha Display
•Custom Zone Descriptors
•Built-in Speaker Sounder
•Dedicated Function Keys
•Backlit Display (permanent display backlighting is
an option on some controls; see the control's
instructions for details).
The following table shows the LEDs and their functions:
LED Function
Red Lights when the system is armed in any mode
Green Lights when the system is "ready" to be armed.
SPECIAL FUNCTION KEYS
The keypads also feature function keys. These keys may be
programmed for panic alarms or other special functions
such as macros. See the control's instructions for details.
Function keys must be held down for at least 2
seconds to activate an alarm; key pairs are activated
immediately.
Function Keys
A or [1] and [✻]
B or [✻] and [#]
C or [3] and [#]
D
WIRING AND INSTALLATION
The keypads can be surface mounted directly to a drywall,
or to a single- or double-gang electrical box.
1. Push the two case release snaps at the bottom of the
keypad with the blade of a medium screwdriver (this will
push in the release snap), then pull that side of the case
back away. Refer to Figure 1 for location of the case back
release snaps.
2. Route wiring from the control panel through the opening
in the case back.
3. Mount the case back to a wall or electrical box.
4. Wire directly from the keypad’s terminal block to the
terminal block on the control panel. (See Wiring Table
below).
NOTE: No more than one wire per terminal may be
connected. If daisy-chained configuration is required,
pig-tail wires together so that only one wire is
terminated under the screw. Use 16-24 AWG wire only!
Wiring Table
Keypad Control Panel Wire Color
▲GData In Green
–– Aux Pwr (GND) Black
++ Aux. Pwr Red
▼YData Out Yellow
See the control panel’s Installation and Setup Guide for
more complete details.
5. Reattach the keypad to its case back.
JKL
AWAY
CODE
ARMED
READY
STAY
OFF
MAX
D
INS
EN
I
GH
RS
PQ
T
TAN
READY
BYPASS
CHIME
TEST
46
TUV
9
0
NO
M
XZ
Y
W
UM
N
EF
D
ABC
3
5
8
2
1
7
*
#
NOTE:
TO REMOVE CASE BACK
PUSH IN THE TWO RELEASE
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT UP.
6460S-001-V1
RELEASE
SNAPS
DCBA
Figure 1. Removing the Case Back
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM

SETTING THE KEYPAD ADDRESS
The keypad can either be set for an address of 00-30, or to
the non-addressable mode (31). The keypad's default
address is 31.
To change the keypad's address, do the following:
1. Enter address mode: Power up the keypad. Within 60
seconds of power-up, press and hold down the [1] and [3]
keys at the same time for 3 seconds. (If unable to enter
address mode, power up and try again.)
The current keypad address will be displayed, and the
cursor will be under the "tens" digit. If 10 seconds have
passed with no key entry, the keypad automatically exits
address mode. You must power down, power up and
start address mode again.
NOTE: The keypad will not enter address mode if the
panel to which it is connected is in programming mode.
2. Set the current address to "00": Press [0] to clear the
current "tens" digit. The cursor will move to the "ones"
digit position. Press [0] to clear the current "ones" digit.
The cursor will move back to the "tens" digit position.
3. Enter the keypad's address: Enter the proper "tens" digit
of the keypad's address. The cursor will move to the
"ones" digit position. Enter the proper "ones" digit of the
keypad's address. Note that address "31" sets the
keypad to non-addressable mode.
4. Exit address mode:
Press [✻] to save the displayed address and exit address
mode.
VIEWING THE KEYPAD ADDRESS
Press and hold down the [1] and [3] keys at the same time
for about 3 seconds. The current address is displayed. No
key entry is allowed. Press any key to exit or wait 10
seconds to exit viewing mode.
FUNCTION KEY LABELS
A set of adhesive-backed labels with some typical function
symbols (i.e., fire, police, personal emergency, etc.) is
provided. These labels can be placed on or next to the keys
to identify each key's function for the end user (as
determined by the control panel's capability and
programming; see the control's instructions).
OPERATING THE KEYPAD
For operating instructions, see the User Guide for the
control panel used with this keypad.
SPECIFICATIONS
Physical: 5-9/16"H x 6-3/4"W x 1"D
Displays: 2 x 16 alpha-numeric supertwist LCD,
backlit.
Sounder: Speaker.
Voltage: 12VDC (power-limited)
Current: 150mA in alarm (ARMED LED lit, LCD
backlight and sounder on), reduces to 40mA
when panel is operating in standby mode
(backlight off).
NFPA-72 Compliant.
REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY
INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright2009 Honeywell International Inc.
www.security.honeywell.com
Ê800-03612rŠ
800-03612 1/09 Rev. B
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM