Honeywell ADEMCO VISTA-120 User manual

N5943-8V4 7/04 Rev A
A
AA
A
A
AA
AD
DD
D
D
DD
DE
EE
E
E
EE
EM
MM
M
M
MM
MC
CC
C
C
CC
CO
OO
O
O
OO
O V
VV
V
V
VV
VI
II
I
I
II
IS
SS
S
S
SS
ST
TT
T
T
TT
TA
AA
A
A
AA
A-
--
-
-
--
-1
11
1
1
11
12
22
2
2
22
20
00
0
0
00
0
Security System
Security SystemSecurity System
Security System
With Scheduling
With SchedulingWith Scheduling
With Scheduling
User Guide

– 2 –
Your Honeywell security system is designed for use with devices manufactured or approved by
Honeywell for use with your security system. Your Honeywell security system is not designed for
use with any device that may be attached to your security system's keypad or other
communicating bus if Honeywell has not approved such device for use with your security system.
Use of any such unauthorized device may cause damage or compromise the performance of your
security system and affect the validity of your Honeywell limited warranty. When you purchase
devices that have been manufactured or approved by Honeywell, you acquire the assurance that
these devices have been thoroughly tested to ensure optimum performance when used with your
Honeywell security system.

– 3 –
TABLE OF CONTENTS
SYSTEM OVERVIEW ....................................5
General .......................................................5
A Partitioned System ..................................5
Panel Linking ..............................................6
Zones..........................................................6
Fire Protection ............................................6
Burglary Protection .....................................7
Alarms.........................................................7
Memory of Alarm ........................................7
Speed Key (Macros) ...................................8
Using Schedules.........................................8
Device Timers.............................................8
To Access Another Partition (GOTO
Command) ..................................................8
Master Keypad Operation...........................9
Self-Help Feature........................................9
Phone Access & Voice Response
Capability ....................................................9
ABOUT THE KEYPADS...............................10
General .....................................................10
FUNCTIONS OF THE KEYPAD ..................11
ENTRY/EXIT DELAYS .................................14
General Information ..................................14
SECURITY CODES & AUTHORITY
LEVELS ....................................................15
General Information ..................................15
Duress Code.............................................15
Quick Arming ............................................15
Authority Levels ........................................16
General Rules on Authority Levels and
Changes ...................................................17
To Exit User Edit Mode.............................17
To Add a User...........................................18
To Change a User's Code ........................20
To Delete a User.......................................20
ACCESSING OTHER PARTITIONS............21
To Access Another Partition .....................21
Global Arming ...........................................21
Master Keypad Operation.........................22
Common Area Operation..........................24
How User Codes Affect the Common
Area ..........................................................25
ACCESSING OTHER PANELS ...................26
Single-Partition Single-Panel Mode..........26
Multi-Partition Multi-Panel Mode...............27
Multi-Panel View Mode .............................28
Priority of Displays for Multi-Partition
and Multi-Panel Modes .............................29
CHECKING FOR OPEN ZONES .................30
Using the ✳READY Key ......................30
BYPASSING PROTECTION ZONES ..........31
Using the 6 BYPASS Key ....................31
Quick Bypass............................................32
Displaying Bypassed Zones .....................32
Using the 3 STAY key..........................33
ARMING PERIMETER ONLY ......................34
Using the 7 INSTANT Key...................34
ARMING ALL PROTECTION.......................35
Using the 2 AWAY Key........................35
ARMING ALL PROTECTION.......................36
Using the 4 MAXIMUM Key .................36
DISARMING AND SILENCING ALARMS ....37
Using the 1 OFF Key ...........................37
Memory of Alarm ......................................37
USING THE KEYSWITCH ...........................38
General .....................................................38
Arming ......................................................38
Disarming..................................................38
CHIME MODE ..............................................39
Using the 9 Key ...................................39
VIEWING ALARM COMPANY
MESSAGES..............................................40
General Information..................................40
Using Panic Keys......................................41

–4 –
SPEED KEY (MACROS) .............................42
General Information.................................. 42
Defining .................................................... 42
Executing..................................................43
ACCESS DOOR CONTROL........................44
General Information.................................. 44
USING #70 RELAY MENU MODE ..............45
General Information.................................. 45
USING SCHEDULES...................................46
Delaying the Closing Time .......................46
Temporary Open/Close Schedules .......... 46
Programming Temporary Schedules .......47
PROGRAMMING DEVICE TIMERS ............ 49
General Information.................................. 49
USING #77 INSTANT ACTIVATION
MODE.......................................................51
EVENT LOG PROCEDURES ...................... 54
General Information.................................. 54
To Display The Event Log ........................54
TESTING THE SYSTEM ............................. 56
Using the 5 TEST Key ......................... 56
Testing Your System ................................ 56
FIRE ALARM SYSTEM................................ 57
In Case Of Fire Alarm............................... 57
Silencing A Fire Alarm .............................. 57
Typical Trouble Displays .......................... 58
Power Failure ........................................... 59
MAINTAINING YOUR SYSTEM .................. 60
Taking Care of Your System .................... 60
Replacing Batteries in Wireless
Sensors .................................................... 60
Silencing Low Battery Warning Tones
at the Keypad ...........................................61
Routine Care ............................................ 61
QUICK GUIDE TO SYSTEM
FUNCTIONS............................................. 62
SUMMARY OF AUDIBLE
NOTIFICATION ........................................ 64
INDEX .......................................................... 68

–5 –
System Overview
General
Your Honeywell security system consists of a main control panel, at least one
keypad, and various sensors strategically positioned throughout the
premises. The system offers you three forms of protection: burglary, fire and
emergency. The keypad provides full control of system operation.
The system uses microcomputer technology to monitor all protection zones
and system status and provides appropriate information for display on the
keypad(s) used with the system, and initiates appropriate alarms. Your
system may also have been programmed to automatically transmit alarm or
status messages over the phone lines to a central alarm monitoring station.
This manual is designed to help you become comfortable operating
your system. Each function is explained in step-by-step detail. We
recommend you read the SYSTEM OVERVIEW section to become
familiar with the terminology and the basic features of the system.
NOTE: If you have a Symphony (Advanced User Interface) connected
to your system, refer to the Symphony User Guide for operating
instructions.
A Partitioned System
A partitioned system shares one physical alarm system among different
users, each with their own requirements. For the most part, you as a user
need not know about other users and their structure in the system, but from
time to time, you may see display messages that indicate the system is in use
by another user. Do not be concerned, this is normal. Refer to the
ACCESSING OTHER PARTITIONS section for additional information.

–6 –
System Overview (cont’d)
Panel Linking
Panel Linking networks up to eight VISTA-120 control panels, enabling a
user to control the features of all control panels from a single location. The
Panel Linking is ideal for multi-building environments (e.g. a shopping mall,
college campus, etc.).
The system provides the following three modes to access other “linked”
control panels:
• Single-Partition, Single-Panel −displays status of a partition on a remote
control panel and allows control of that remote control panel.
• Multi-Partition, Multi-Panel Mode −displays status and allows
arming/disarming of multiple partitions at once on a remote control
panel.
• Multi-Panel View Mode −displays status and allows arming/disarming of
multiple remote control panels at a time.
Zones
Your system's sensing devices have been assigned to various "zones." For
example, the sensing device on your Entry/Exit door may have been assigned
to zone 001, sensing devices on windows in the master bedroom to zone 002,
and so on. These numbers will appear on the display, along with an alpha
descriptor for that zone (if programmed), when an alarm or trouble condition
occurs.
Fire Protection
The fire protection portion of your security system (if used) is always on and
will sound an alarm if a fire condition is detected. Refer to the FIRE ALARM
SYSTEM section for important information concerning fire protection, smoke
detectors and planning emergency exit routes from your house.

–7 –
System Overview (cont’d)
Burglary Protection
The burglary protection portion of your system must be turned on or "armed"
before it will sense burglary alarm conditions. Your system provides four
modes of burglary protection: STAY, AWAY, INSTANT and MAXIMUM, and
even allows you to BYPASS selected zones of protection while leaving the
rest of the system armed. The system also provides a CHIME mode, for
alerting users to the opening and closing of doors and windows while the
system is disarmed. Refer to the other sections of this manual for procedures
for using these features.
The following table lists the four different arming modes and the results of
each.
Features For Each Arming Mode
Arming Mode Exit Delay Entry Delay Perimeter Armed
AWAY Yes* Yes Yes
STAY Yes Yes Yes
INSTANT Yes No Yes
MAXIMUM Yes* No Yes
*If final contact arming has been enabled by your installer, you have unlimited exit
delay. This means your system will not arm until the exit door is either opened and
closed or just closed (if opened initially).
Alarms
When an alarm occurs, both the keypad and external sounders will sound,
and the keypad will display the zone(s) causing the alarm. If your system is
connected to a central monitoring station, an alarm message will also be sent.
To stop the alarm sounding, simply disarm the system.
Memory of Alarm
When an alarm condition occurs, the keypad displays the number(s) of the
zone(s) that caused the problem, and displays the type of alarm (ex. FIRE,
ALARM). It remains displayed until it is cleared by disarming the system
(see DISARMING THE SYSTEM section).

–8 –
System Overview (cont’d)
Speed Key (Macros)
The system can store a string of up to 32 keystrokes, which can be activated
anytime by simply pressing the “A, B, C, or D” keys. This feature can be
used to make it easy to perform multiple functions at once (such as going to
another partition to bypass a zone), or it can be used to simplify an everyday,
repeated procedure. Refer to the SPEED KEY section for procedures for
using this feature.
Using Schedules
Your system may have been programmed with schedules for automatically
arming, disarming and activating various devices and/or performing other
system functions at predetermined times. Users can modify some of these
schedules by manually delaying a closing time, using temporary schedules, or
by programming special user schedules. Refer to the USING SCHEDULES
section at the end of this manual for scheduling related procedures.
Device Timers
The system provides up to 20 "timers" that can be used to control various
devices, such as lights or appliances. These timers are similar in concept to
the individual appliance timers that might be purchased at a department
store. The devices that can be controlled are programmed into the system by
the installer. Up to 96 of these devices can be programmed. Refer to the
PROGRAMMING DEVICE TIMERS section for procedures.
To Access Another Partition (GOTO Command)
Each keypad is assigned a default partition for display purposes, and will
show only that partition's information. But, if the user is authorized, a
keypad in one partition can be used to perform system functions in another
partition, by using the GOTO command. Note that only those partitions
authorized and programmed by the installer can be accessed in this manner.
To GOTO another partition, enter your security code, then press [✳]followed
by the desired partition number (1-8).
The keypad will remain in the new partition until directed to go to another
partition, or until 120 seconds has elapsed with no keypad activity. Entering
your security code, pressing [✳]followed by [0] will return the keypad to its
original partition.

–9 –
System Overview (cont’d)
Master Keypad Operation
A "Master" keypad is one on which the status of all 8 partitions is displayed
simultaneously. A user can get more information about a certain partition by
simply entering [✳]+ the desired partition number (1-8). To log on to the
"Master" partition (9) using the GOTO command, and to perform any
functions at a Master keypad, a user must have access to all partitions.
Self-Help Feature
Abbreviated user's instructions are built into the system that can be easily
viewed on the alpha keypad's message display screen. This feature will prove
particularly useful if this manual is not conveniently accessible when you
need to perform a system procedure with which you are not familiar.
To view the abbreviated instructions:
Simply press and hold down the function key of interest until the description
starts to appear (about 5 seconds) and then release it. The system must be
“READY TO ARM” to perform this function.
Refer to the FUNCTIONS OF THE KEYPAD section for descriptions of each
key function.
Phone Access & Voice Response Capability
Your system may include a 4286 VIP or TeleCommand Telephone access
module that will permit you to access the system via a multi-frequency, push-
button phone, either on-premises or by call-in when away. The phone access
feature will enable you to do the following:
• Receive synthesized voice messages via the telephone regarding the
status of the security system.
• Arm and disarm the system and perform most function commands via
the telephone, with voice confirmation provided after each command
entry.
• Control 4204/4204CF relays devices and lights and appliances through
the #70 Manual Relay Activation mode.
Complete information regarding the use of this feature is provided in a
separate manual entitled PHONE ACCESS USER'S GUIDE, which
accompanies the 4286 VIP or TeleCommand Telephone access module.

–10 –
About The Keypads
General
IMPORTANT: If the keypad beeps rapidly upon entering the
premises, it indicates that an alarm has occurred during your
absence. LEAVE IMMEDIATELY and CONTACT THE POLICE
from a safe location nearby.
NOTE: If you have a Symphony (Advanced User Interface) connected
to your system, refer to the Symphony User Guide for operating
instructions for this unit.
Your keypads allow you to control all system functions. The keypads feature
a telephone style (digital) keypad and a Liquid Crystal Display (LCD) that
shows the nature and location of all occurrences. These keypads can display
system messages in the local language. Abbreviated user’s instructions can
be displayed (see Self Help paragraph in the SYSTEM OVERVIEW section).
These keypads can also be programmed with custom zone descriptors.
Keypad display back lighting is programmable to always stay on or to light
only when a key is pressed, then turn off a few minutes later.
The keypads also feature a built-in sounder that will sound during alarms
and troubles. It will also "beep" during certain system functions, such as
during entry/exit delay times, during CHIME mode, and when depressing
keys to perform system functions (to acknowledge the key press). These
sounds can be optionally suppressed in some of your keypads (so as not to
disturb other users of the system). Ask your installer if this has been done.

–11 –
Functions Of The Keypad
CPU
ARMED
READY
6164-009-V0
OFF
4
MAX
7
INSTANT
READY
2
AWAY
TEST
CODE
0
3
STAY
6
BYPASS
CHIME
1
5
89
#
SPEAKER
LCD
DISPLAY
FUNCTION
KEYS
LEDS
IMPORTANT!: When using the keypad to enter codes and commands,
sequential key depressions must be made within 3 seconds of one
another. If 3 seconds elapses without a key depression, the entry is
aborted and must be repeated from its beginning.
Note: The Keypad Code Tamper option locks outs all keypads in the partition following the
entry of 21 keystrokes without entering a valid code + command sequence (within a 15-
minute period) and lasts a total of 15 minutes. This is also true for any wireless keypads in
the partition. Check with your installer to see if this option has been enabled in your
system.

–12 –
Functions Of The Keypad (cont’d)
ALPHA DISPLAY WINDOW: A 2-line,
32-character Liquid Crystal Display (LCD).
Displays protection point identification and
system status, messages, and user
instructions.
1 OFF : Disarms the burglary portion of
the system, silences alarms and audible
trouble indicators, and clears visual alarm
trouble after the problem has been
corrected.
2 AWAY : Completely arms both
perimeter and interior burglary protection
by sensing an intruder's movements
through protected interior areas as well as
guarding protected doors, windows, etc.
Late arrivals can enter through an entry
delay zone without causing an alarm if the
system is disarmed before the entry delay
time expires.
3 STAY : Arms the perimeter burglary
protection, guarding protected doors,
windows and other perimeter protection
points, and sounds an alarm if one is
opened. Allows automatic bypassing of
certain areas, which allows movement
within your house without causing an
alarm. Late arrivals can enter through an
entry delay zone without causing an alarm
if the system is disarmed before the entry
delay time expires. See ARMING
PERIMETER ONLY for a full explanation
of the STAY key.
4 MAXIMUM : Arms in manner similar
to AWAY mode, but eliminates the entry
delay period, thus providing maximum
protection. An alarm will occur
immediately upon opening any protection
point, including entry delay zones.
5 TEST : Tests the system and alarm
sounder if disarmed.
6 BYPASS : Removes individual
protection zones from being monitored by
the system. Displays previously bypassed
protection zones.
7 INSTANT : Arms in manner similar
to STAY mode, but turns off the entry
delay period, offering greater security
while inside and not expecting any late
arrivals. An alarm will occur immediately
upon opening any perimeter protection
point, including entry delay zones.
8 CODE : Allows the entry of additional
user codes that can be given to other users
of the system.

–13 –
Functions Of The Keypad (cont’d)
9 CHIME : Turns on & off the CHIME
mode. When on, any entry through a
protected delay or perimeter zone while the
system is disarmed will cause a tone to
sound at the Keypad(s).
✳READY : When depressed prior to
arming the system, the keypad will display
all open protection zones within the
keypad's home partition. This key is also
used to display all zone descriptors that
have been programmed for your system, by
holding the key down for at least 5 seconds.
#: Permits ARMING of the system
without use of a security code ("Quick
Arm", if programmed).
KEYS 0-9: Used to enter your individual
security access code(s).
LED READY INDICATOR: (GREEN) Lit
indicates system is ready to be armed,
while unlit indicates system not ready.
LED ARMED INDICATOR: (GREEN)
Lit when the system has been armed
(STAY, AWAY, INSTANT or MAXIMUM).
CPU INDICATOR: (YELLOW) Lit when
a CPU failure has been detected inside the
keypad.
SPEAKER: Source of audible internal
warning and confirmation sounds, as well
as alarms (see "Summary of Audible
Notifications").
FUNCTION KEYS: These keys can be
used for Speedkey (macros) functions or
panic keys. Refer to the SPEEDKEY
(MACROS) and PANIC KEYS sections for
descriptions of these functions.

–14 –
Entry/Exit Delays
General Information
Your system has installer-programmed time delays, known as exit delay and
entry delay. Whenever you arm your system, exit delay gives you time to
leave through the designated exit door without setting off an alarm. Exit
delay begins immediately after entering any arming command, and applies to
all modes of arming protection. If programmed, a slow beeping will sound
throughout the exit delay period.
Entry Delay gives you time to disarm the system when you reenter through
the designated entrance door. But the system must be disarmed before the
entry delay period ends, or an alarm will occur. The keypad will beep during
the entry delay period, reminding you to disarm the system. You can also
arm the system with no entry delay at all by using either INSTANT or
MAXIMUM arming modes. These modes provide greater security while on
the premises or while away for extended periods of time. See your installer
for your delay times.

–15 –
Security Codes & Authority Levels
General Information
At the time of installation, you were assigned an authority level and a
personal four-digit security code, known only to you and yours. The security
code must be entered when arming and disarming the system. The authority
level defines the system functions that you can perform.
As an additional safety feature, other users that do not have a need to know
your code can be assigned different security codes, and each user can be given
a different authority level. Users are identified by "user numbers", which are
assigned when assigning a user's security code.
All codes can be used interchangeably when performing system functions
within the limits of each code's authority level (a system armed with one
user's code can be disarmed by another user's code), with the exception of the
Operator Level C code. See AUTHORITY LEVELS on the following page for
details regarding authority levels.
If more than 20 key presses are made within a 15-minute period without
entering a valid command sequence, the system will ignore all subsequent
key presses for the next 15 minutes. Check with your installer to see if this
option has been enabled in your system.
Important: Only users assigned for user numbers 001-050 can perform
panel linking functions.
Duress Code
This feature is intended for use if you are forced to disarm or arm the system
under threat. When used, the system will act normally, but can silently
notify the central station of your situation, if that service has been provided.
The duress code is pre-assigned by the installer during installation (authority
level 6).
Important: This code is useful only when the system is connected to a
central station.
Quick Arming
Note that if "Quick Arming" was programmed by the installer, the [#] key
can be pressed in place of the security code when arming the system. The
security code must always be used to disarm the system, however.

–16 –
Security Codes & Authority Levels (cont’d)
Authority Levels
Authority levels define the system functions a particular user can perform.
Depending on the authority assigned to you, there are certain system
functions you may be prohibited from performing. In summary, there are six
authority levels, each having certain system restrictions as shown below.
Level 1 Master: Can perform all system functions in assigned
partitions, and can add, delete or change Manager
and Operator level users. Master codes are added
by the Installer.
Level 2 Manager: Can perform system functions in assigned
partitions, and can add, delete or change Operator
level users.
Level 3 Operator A: Can perform system functions in assigned
partitions, but cannot add or delete other users.
Level 4 Operator B: Same as Operator A, except Operator B cannot
bypass zones of protection.
Level 5 Operator C: Can arm the system in assigned partitions, but
cannot disarm the system unless the system was
armed with this code. This code is typically
assigned to someone who has a need to
arm/disarm the system only at certain times (such
as a baby-sitter).
Level 6 Duress: Can arm and disarm the system, but also sends a
silent panic alarm to the central station, if that
service is connected.
To view your authority level and system capabilities:
1. Enter your code + [✳] +[✳].
2. The keypad will display the partition(s) that you are authorized to
operate, and your user number and authority level in each partition.

–17 –
Security Codes & Authority Levels (cont’d)
General Rules on Authority Levels and Changes
• A user may not delete or change the user code of the SAME or HIGHER
authority than which he is assigned.
• A user may only ADD users to a LOWER authority level.
• A user may assign access codes only to those partitions to which the user
adding the code has access. (ex. a user with access to only partition 1
cannot assign codes in partition 2.)
• The only way to assign a user's authority level is by using the "Add A
User" procedure. To change a user's authority level, that user must first
be deleted, then added again.
• A user can only be DELETED or CHANGED from within the partition he
is assigned.
• User numbers must be entered as 3-digit entries. Single digit user
numbers must be preceded by a "00" (example, 003, 004, etc.). Security
codes are entered as 4-digit numbers.
• Before assigning a security code, be sure it does not conflict with any
DURESS code.
Note: When adding, changing or deleting users, all other alpha keypads in
that partition will display "User Edit Mode – Please Stand By", and key
depressions (except Panic) at those keypads will be ignored. Panic key
depressions will cause an alarm and terminate user entry.
To Exit User Edit Mode
You can exit any of the user edit modes described on the following pages at
any time by doing the following:
1. Press either ✳or # , or don't press any key for 10 seconds.
2. System returns to normal mode.

–18 –
Security Codes & Authority Levels (cont’d)
To Add a User
IMPORTANT: Temporary users should not be shown how to use any system
function they do not need to know (e.g. bypassing protection zones).
CODE
1. Enter Master or Manager code and press the 8 key.
2. Enter the new user's 3-digit User Number (002-150).
3. Enter 4-digit security code for that user. The following prompts will
appear.
ADD NEW USER?
0 = NO , 1 = YES
Enter 1 to add a new user code. Entering 0 will
change the existing user's code to the code entered
in step 3. See Changing A User's Code section.
USER NUMBER = 003
ENTER AUTH. LEVEL
Enter the authority level, 1-6, for this user within
this partition.
1=master 2=manager 3=operator A
4=operator B 5=operator C 6=duress code
ACCESS GROUP?
ENTER 0-8
If access schedules have been programmed, this
prompt appears. Enter the user's access group
number (1-8) if this user should have limited
access to the system. Enter 0 if no access group
should be assigned.
RF BUTTON ?
0 = NO , 1 = YES
This prompt will appear if a 5800 series button
transmitter has been supplied and has not yet been
assigned to a user. Press 1 if a button transmitter
will be assigned to this user. Otherwise press 0.
ENTER BUTTON ZN #
(001-128)
If assigning a button transmitter, this prompt will
appear. Enter the button's zone number (see your
installer for zone number).
MULTI-ACCESS ?
0 = NO , 1 = YES
If you as a user have access to other partitions, the
keypad will prompt for ability of this new user to
access (GOTO) those partitions. Press 0 (NO) or 1
(YES). If no, the system activates this user code and
exits “Add a User” mode. If yes, the keypad prompts
for the Global Arm option for this user.

–19 –
Security Codes & Authority Levels (cont’d)
GLOBAL ARM ?
0 = NO , 1 = YES
Press 1 (YES) if this user will be allowed to try to
arm more than one partition at the same time.
Press 0 if this user will arm only his assigned
partition.
PART.2 - SHOP?
0 = NO , 1 = YES
The keypad now prompts for the user’s access to the
next partition (see GOTO command). Again press 0
or 1. If yes, the system will automatically assign a
user number for use in that partition and will
prompt for authority level and global arm options
for this user within the partition (see previous
steps).
PART. 1 A0* WHSE
USER 003 AUTH=3G.
When all partitions have been displayed, the
keypad will scroll through the partition(s) to which
access has been assigned, and will display the user
number, authority level and global arm option for
each. The “G” after the authority level indicates
that the global arm feature is active for this user in
the displayed partition. The "*" indicates the
partition from which this user can be changed or
deleted. The "." at the end of the second line
indicates that this user sends open/close reports.
Open/close reporting is automatically active for any
users added by you, if you have open/close reporting
active.

–20 –
Security Codes & Authority Levels (cont’d)
To Change a User's Code
CODE
1. Enter Master or Manager code and press the 8 key + user number
to be changed.
2. Enter the new code for that user.
ADD NEW USER?
0 = NO , 1 = YES
The system will recognize that the user number is
already in use and will prompt whether or not this
is a new user. Enter 0 to change the existing
user's code to the code entered in step 3.
USER 002 CHANGED
SUCCESSFULLY
The system will confirm that the change is allowed
based on authorization level, and if so, will put the
new code into effect.
Note that if changing one’s own code, the
system will prompt for the new code to be re-
entered. This prevents accidentally changing one's
own code.
To Delete a User
CODE
1. Enter Master or Manager code and press the 8 key + user number
to be deleted.
2. Enter Master or Manager code first entered.
OK TO DELETE
0 = NO , 1 = YES
The system will recognize that the User number
is already in use and will prompt to confirm that
it should be deleted. Press 0 (NO) or 1 (YES).
USER CODE
DELETED
If yes, that user's code will be removed from all
partitions to which it was assigned, and all
authorization levels and other information about
that user will be deleted. Note that a user can
only be deleted from the partition in which it was
first assigned, and can only be deleted by a user
with a higher authority level. A User's security
code cannot be deleted by oneself.