Honeywell LXL-1000 User manual

K9350V1 3/05 Rev. A
ADEMCO LYNX XL SERIES
ADEMCO LYNX XL SERIESADEMCO LYNX XL SERIES
ADEMCO LYNX XL SERIES
Security Systems
Security SystemsSecurity Systems
Security Systems
LXL
LXLLXL
LXL-
--
-1000/LXL
1000/LXL1000/LXL
1000/LXL-
--
-1010
10101010
1010
User Guide
User GuideUser Guide
User Guide
www.PDF-Zoo.com

– 2 –
SYSTEM COMPATIBILITY NOTICE
Your Honeywell security system is designed for use with devices manufactured
or approved by Honeywell for use with your security system. Your Honeywell
security system is not designed for use with any device that may be attached to
your security system's keypad or other communicating bus if Honeywell has not
approved such device for use with your security system. Use of any such
unauthorized device may cause damage or compromise the performance of your
security system and affect the validity of your Honeywell limited warranty.
When you purchase devices that have been manufactured or approved by
Honeywell, you acquire the assurance that these devices have been thoroughly
tested to ensure optimum performance when used with your Honeywell security
system.
IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible point
of entry to a home or commercial premises. This would include any skylights
that may be present, and the upper windows in a multi-level building.
In addition, we recommend that radio backup be used in a security system so
that alarm signals can still be sent to the Central Monitoring Station in the
event that the telephone lines are out of order (alarm signals are normally sent
over the phone lines).
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors
have played a key role in reducing fire deaths in the United States. With regard
to the number and placement of smoke/heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Association's
National Fire Alarm Code (NFPA 72). These recommendations can be found in
this manual.
About This Manual
This manual is a step-by-step guide that will acquaint you with the system's
features and benefits. It defines the components and their functions, describes
their operation, and provides clear step-by-step instructions for normal and
emergency procedures. Keep this manual in a convenient place so that you can
refer to it as necessary.
www.PDF-Zoo.com

– 3 –
Table of Contents
System Overview......................................................................................................................... 5
Introduction........................................................................................................................... 5
System Basics ...................................................................................................................... 5
Using the Voice Message Center ......................................................................................... 8
About The Keypads..................................................................................................................... 9
General Information .............................................................................................................. 9
FIXED-WORD DISPLAY KEYPAD ....................................................................................... 11
Functions of the Keypads ......................................................................................................... 12
Entry/Exit Delays ....................................................................................................................... 15
Entry Delay ......................................................................................................................... 15
Exit Delay ............................................................................................................................ 15
Exit Alarms .......................................................................................................................... 16
Checking For Open Zones........................................................................................................ 17
Using the [∗] Key to Display and Announce System Status .............................................. 17
Arming the System.................................................................................................................... 18
STAY Mode: Arms Perimeter Only, Entry Delay On ........................................................... 18
NIGHT-STAY Mode: Arms Perimeter Only, Plus Selected Zones ...................................... 18
INSTANT Mode: Arms Perimeter Only, Entry Delay Off ..................................................... 18
AWAY Mode: Arms Entire System, Entry Delay On ........................................................... 18
MAXIMUM Mode: Arms Entire System, Entry Delay Off..................................................... 18
Arming Commands............................................................................................................. 19
Single Button Arming.......................................................................................................... 20
Single Button “Step” Arming .............................................................................................. 20
Disarming and Silencing Alarms............................................................................................... 21
Bypassing Protection Zones ..................................................................................................... 22
Using the BYPASS Key....................................................................................................... 22
Quick Bypass...................................................................................................................... 23
Chime Mode.............................................................................................................................. 24
Using the Chime Mode....................................................................................................... 24
Using the Voice Chime ....................................................................................................... 24
Date and Time........................................................................................................................... 25
Viewing the Current Date and Time.................................................................................... 25
Setting the Date and Time .................................................................................................. 25
Panic Keys................................................................................................................................. 26
Using Panic Keys................................................................................................................ 26
www.PDF-Zoo.com

– 4 –
Macro Key Programming & Usage ........................................................................................... 27
About Macro Keys .............................................................................................................. 27
Example of Macro Programming........................................................................................ 28
Using a Programmed Macro Key ....................................................................................... 28
Using Device Commands ......................................................................................................... 29
About Device Commands................................................................................................... 29
Paging Feature.......................................................................................................................... 30
About Automatic Paging..................................................................................................... 30
About Manual Paging ......................................................................................................... 31
Latch Key Paging................................................................................................................ 31
Security Codes & Authority Levels............................................................................................ 32
About Security Codes......................................................................................................... 32
Authority Level Definitions .................................................................................................. 32
How to Assign User Codes and Attributes ......................................................................... 33
Scheduling ................................................................................................................................ 34
About Scheduling ............................................................................................................... 34
Creating Schedules ............................................................................................................ 34
Event Logging Procedures ....................................................................................................... 36
About Event Logging .......................................................................................................... 36
Viewing the Event Log ........................................................................................................ 36
Table of Event Log Codes .................................................................................................. 37
Testing the System.................................................................................................................... 38
About Testing the System .................................................................................................. 38
Trouble Conditions.................................................................................................................... 39
Maintaining Your System .......................................................................................................... 42
Fire Alarm System ..................................................................................................................... 43
Quick Guide to Basic System Functions .................................................................................. 47
Summary of Audible/Visual Notifications .................................................................................. 48
Regulatory Statements and Warnings ...................................................................................... 50
System Features Log ................................................................................................................ 51
User Setup .......................................................................................................................... 52
Paging Setup ...................................................................................................................... 53
List of Output Devices......................................................................................................... 53
LIMITATIONS OF THIS SYSTEM............................................................................................... 54
Index.......................................................................................................................................... 57
One Year Warranty.................................................................................................................... 61
www.PDF-Zoo.com

– 5 –
System Overview
Introduction
Congratulations on your ownership of a Honeywell Security System. You've made a
wise decision in choosing this system because it represents the latest in security
protection technology available today.
U
UU
UL
LL
LThe LXL-1000/1010 is not intended for UL fire or commercial burglary applications
This system provides:
•Three forms of protection: burglary, fire* and emergency
•At least one keypad, which provides control of system and displays system status
•Various sensors for perimeter and interior burglary protection
•Smoke or combustion detectors* designed to provide early warning in case of fire.
Your system may also have been programmed to automatically send alarm or status
messages over the phone lines to a Central Monitoring Station.
* Commercial installations and some residential systems may not include fire
protection – check with your installer.
System Basics
Burglary Protection
•Several modes of burglary protection: Stay, Night-Stay, Away, Instant, Maximum.
STAY: arms perimeter zones only and entry delay is on
INSTANT: same as STAY, except entry delay is off
NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on
AWAY: arms perimeter and all interior zones, entry delay is on
MAXIMUM: same as AWAY, except entry delay is off
•You can BYPASS selected zones while leaving the rest of the system armed.
•CHIME mode alerts you to the opening of protected doors and windows while the
system is disarmed.
Fire Protection
U
UU
UL
LL
LThe LXL-1000/1010 is not intended for UL fire applications
•Fire protection is always active (if installed) and an alarm sounds if a fire
condition is detected
•If necessary, you can manually initiate a fire alarm using the keypad (if
programmed).
•Refer to the Fire Alarm System section for information regarding fire protection,
smoke detectors and planning emergency exit routes.
www.PDF-Zoo.com

– 6 –
System Overview (cont’d)
Security Codes
•You were assigned a 4-digit security code during system installation.
•Use your security code when arming and disarming the system, and when
performing other system functions.
•Other users can be assigned different security codes, each with different
authority levels, which define the system functions a particular user can perform.
Zones
•The system sensing devices have been assigned to various “zones,” which are specific
areas of protection (e.g., front door, kitchen window, etc.). •Zone numbers are
displayed at the keypad when an alarm or trouble condition occurs on a sensor.
Arming, Step-Arming and Disarming Burglary Protection
•The system must be armed before the burglary protection can sense intrusions.
•To arm your system, enter your user code followed by the desired arming key.
•If programmed, the [#] key can be pressed instead of entering the security code
when arming the system.
•You can also use the step-arming feature if programmed, to arm the system. This
is a function key that allows you to arm the system in one of three modes by
simply pressing the key repeatedly.
•To disarm the system, enter your user code, then press the [OFF] key.
Alarms
•When an alarm occurs, both the keypad and external sounders will sound, and
the keypad will display the zone(s) causing the alarm.
•If your system is connected to a Central Monitoring Station, an alarm message
will also be sent.
•To stop the alarm sounding, simply disarm the system.
Memory of Alarm
•When an alarm condition occurs, the keypad displays the number(s) of the
zone(s) that caused the problem, and displays the type of alarm.
•The message remains displayed even after disarming the system, but can be
cleared with another “off” sequence.
Function Keys
•Some keypads may contain “A,” “B,” “C,” and “D” keys that can be programmed
to perform various functions.
•Functions include: activate a panic alarm, arm the system, provide step arming,
switch lights on/off, send a message to a pager, display Time/Date, and start a
programmed Macro sequence.
www.PDF-Zoo.com

– 7 –
System Overview (cont’d)
Paging Feature
•If programmed, the system can automatically send certain system condition
messages to up to two pagers.
•The display consists of code numbers that indicate the type of condition that has
occurred, if your system is using phone lines.
Scheduling
•Your system can be programmed to automatically perform certain functions (e.g.,
arm the system) at a predetermined time each day.
LED Indications
The control utilizes three Security System Control Status LEDs that indicate
control arming state and power status as follows:
READY LED (Green)
Lit when the system is disarmed
and ready to be armed (no open
zones). If the system is disarmed
and the green light is off, the
system is not ready (one or more
zones are open).
POWER LED (Yellow):
Indicates system power status.
• Lit Steady = AC power on and
battery good.
• Rapid Blinking = AC power off.
• Slow Blinking = Low Battery
• Off = AC power off and
discharged battery
ARMED LED (Red):
Lit when system is armed AWAY
or STAY mode.
www.PDF-Zoo.com

– 8 –
System Overview (cont’d)
Using the Voice Message Center
Voice keypads feature a voice message
center that lets you record and playback
one message.
•The message can be up to 2.5-minutes
long.
•The message remains in the Keypad’s
memory until a new message is
recorded.
•The volume control of the message is
adjustable.
•Refer to the procedures below when
using the Message Center functions.
5828V-00-004-V0
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
MESSAGE
MIC
ARMED
READY
RECORD VOLUME PLAY
STATUS FUNCTIONVOICE
SPEAKER
CONTROL
LEDS
FUNCTION
KEYS
LCD
DISPLAY MICROPHONE
MESSAGE
LED
Message Center Functions
To… Press these keys… Notes…
record a
message #
FUNCTION + 0 VOICE + 1 OFF RECORD
The red MESSAGE LED lights.
Message remains in memory
until a new message is recorded.
end
recording 1 OFF
RECORD
The red MESSAGE LED flashes,
indicating message waiting.
play a
message #
FUNCTION + 0 VOICE + 3 STAY PLAY
The recorded message plays and
the red MESSAGE LED turns
off.
adjust the
volume #
FUNCTION + 0 VOICE + 2 AWAY VOLUME , then press
volume key [3] ↑(up) or [6] ↓(down)
Adjusting message volume also
adjusts status volume. Volume
cannot be adjusted while
playing.
www.PDF-Zoo.com

– 9 –
About The Keypads
General Information
Your keypads allow you to control all system functions and are activated by pressing
any numbered key. Your keypads feature the following:
•A telephone style (digital) keypad
•Liquid Crystal Displays (LCD) that show the nature and location of all occurrences
•Built-in sounder that sounds during alarms and troubles. The sounder also "beeps"
during certain system functions and also when depressing any of the keys (to
acknowledge the key press).
•Backlighting of the LCD display windows. Backlighting turns on when any key is
pressed or when entering the premises through any assigned entry/exit door. This
feature is helpful when a keypad is located in a dimly lit area.
•Some keypads have a voice feature that announces the nature and location of all
system occurrences. Voice keypads also announce any faulted entry/exit or
perimeter zone when Chime mode is on. Ask your installer if this option has been
programmed for your system.
IMPORTANT: If the keypad beeps rapidly upon entering the premises, it indicates that an
alarm has occurred during your absence and an intruder may still be on the premises.
LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.
Your keypads are functionally the same, but may have different types of displays, depending
on the type installed with your system.
Alpha Display 2-line alpha display keypads feature a 2-line, 32-character
alphanumeric LCD that displays system messages in friendly
English. These keypads can also be programmed with custom zone
descriptors.
Fixed-Word Display Fixed-Word display keypads are functionally identical to Alpha
display keypads, but the LCD display uses pre-designated words to
identify the nature and location of occurrences.
Voice Keypads Voice Keypads (if installed), are functionally the same as other
keypads, except that these keypads can provide the following:
•Voice announcements of system status (see Checking for Open
Zones section)
•Voice chime, which can alert you to the opening of doors and
windows while the system is disarmed (see Voice Chime in Chime
mode section)
•Message center, which lets you record and playback
messages (see Using the Voice Message Center in the
System Overview section).
www.PDF-Zoo.com

– 10 –
About The Keypads (cont’d)
U
UU
UL
LL
L
The 5839, 5828 and 5828V keypads cannot be used for UL Installations. For UL installations the
5827BD keypad must be used.
5828V-00-005-V0
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
MESSAGE
MIC
ARMED
READY
RECORD VOLUME PLAY
STATUS FUNCTIONVOICE
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
ARMED
READY
5828-00-001-V0
5828V
FIXED-WORD KEYPAD
5828
FIXED-WORD KEYPAD
5839-004-V0
PANIC
READY
INSTANT CODE CHIME
MAX TEST BYPASS
OFF AWAY STAY
456
78
0#
123
9
****
DISARMED
READY TO ARM
****
*
FIRST PRESS ANY KEY
TO PLACE KEYPAD
INTO ACTIVE STATE.
THEN PRESS KEY
TO OBTAIN STATUS.
*
SPECIAL
FUNCTION KEYS
5839 Alpha Display Keypad
www.PDF-Zoo.com