HP Vectra 525 User manual

The HP 525 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED
802.11a/b/g/n/ac product. The Wi-Fi CERTIFIED Logo is a certification
mark of the Wi-Fi Alliance.
HP 525 Wireless Dual-Radio
802.11ac Access Point Quick Start
Guide
This quick start guide shows you how to install and get started using the HP
525 Wireless Dual Radio 802.11ac Access Point (RMN BJNGA-FB0004)
JG993A(AM), JG994A(WW), JG995A(JP), JG996A(IL), JG997A(8pack
AM), JG998A(8pack WW), hereafter referred to as the HP 525.
Views
Figure 1 Views
Rear view
1: Mounting hole
2: Antenna port
Front view Bottom view
3: 2.4 GHz antenna port
4: Console port
5: Reset button
6: Ethernet port 2
7: Ethernet port 1 (support for PoE)
8: 48 VDC power port
9: Security slot
10:5 GHz antenna port
1 2
34678
5 9
10
1

Package contents
The AP, mounting hardware, MAC address label, and documentation.
Ports
The AP provides the following ports:
•
Two auto-sensing 10/100/1000 BASE-T Ethernet port with an RJ-45
connector—Ethernet port 1 that supports PoE and Ethernet port 2.
•
Standard console (serial) port with an RJ-45 connector.
•
Two 2.4 GHz antenna ports and two 5 GHz antenna ports.
•
48 VDC power port.
Caution: Never connect the console port to an Ethernet switch or PoE power
source. This can damage the AP. You can connect the console port only to a
serial port by using an RJ-45 connector or to a serial port adapter.
Radio and antennas
The AP supports two radios: 802.11a/n/ac on Radio 1 and 802.11b/g/n on
Radio 2 with 2x2 MIMO two spatial stream.
The AP contains four internal dual-band, MIMO antennas. It also provides two
antenna ports for each radio.
Reset button
The reset button is on the front panel of the AP. To reset the AP, press the button
for 0 to five seconds. To restore the AP to the factory setting, press the button
for more than five seconds and less than fifteen seconds.
2

Status LEDs
Table 1 LED description
Status
Description
Flashing green at 1
Hz
The AP is booting.
NOTE:
When the AP operates as a fit AP, it is always in this state
before it is registered to an AC.
Slowly pulsing green Connections are present on the 2.4 GHz radios.
Flashing blue at
0.25 Hz
The AP has been booted and has registered to the AC. It is
in standby state (no client is associated with the AP).
Flashing blue at 4
Hz
The AP is upgrading its system software image.
Slowly pulsing blue Connections are present on the 5 GHz radios.
Steady orange An initialization exception has occurred to the AP.
Flashing orange at 1
Hz The AP cannot detect any radio interface.
Flashing orange at
8 Hz
An Ethernet port or radio interface is operating incorrectly.
Cycle
through two
green pulse
s then
two blue pulses
Connections are present on both the 2.4 GHz and 5 GHz
radios.
Powering the HP 525
The AP can be powered by:
•
A 10/100 or 10/100/1000 PoE-enabled switch. Various PoE-enabled
switches are available from HP.
•
A PoE power injector, such as J9407B.
•
An HP 48 volt power adapter, JD055B.
3

The AP requires 802.3af-compliant PoE. For best performance, HP
recommends that you use a gigabit connection.
Caution: If the AP will be powered by a user-supplied PoE power injector,
use only a gigabit-compatible power injector. Although 10/100 PoE-enabled
switches are compatible, PoE injectors designed for 10/100 networks only
are not compatible with the AP.
Important information to read before
installing
Professional installation is required. For indoor installation only. Before
installing or using the AP, consult with a professional installer trained in RF
installation and knowledgeable in local regulations including building and
wiring codes, safety, channel, power, and license requirements for the
intended country. The end user is responsible for ensuring that installation and
use comply with local safety and radio regulations.
To avoid possible bodily injury or equipment damage, read the following
safety recommendations before you install t h e A P. The recommendations do
not cover every possible hazardous condition.
•
Keep the chassis clean and dust-free.
•
Make sure the ground is dry and flat and anti-slip measures are in place.
•
Do not place the AP in a moist area and avoid liquid surrounding the AP.
•
Keep the chassis and installation tools away from walkways.
Selecting the installation site
Consider the following when you select the installation site for the AP:
•
To meet regulatory RF exposure requirements, install the AP and any
external antennas at least 40 cm (15.75 inches) from any person.
•
Install APs away from RF-emitting electronic devices, such as microwave
ovens.
•
Do not install APs in a location where water seepage or condensation
occurs.
4

•
Do not place the AP on a metal surface.
•
Install the AP where there are no obstacles and wireless clients can
receive a strong signal from the AP.
Installation
The AP can be mounted on a wall, a suspended ceiling or a ceiling. When
you mount the AP on a wall, suspended ceiling, or ceiling, mount the AP
bracket first, and then attach the AP to the bracket.
For more information, see HP 525 Wireless Dual Radio 802.11ac Access Point
Installation Guide.
Preparing for installation
HP recommends that you connect power and verify the Ethernet cable and
LEDs before you install the AP in a hard-to-reach location.
Record the MAC address and AP serial number for future reference. If part of
the power line is routed outdoors, connect the AP power cord to a
user-supplied power strip with lightning protection.
Mounting the AP on a wall
1. Hold the mounting bracket with the narrow end facing up. Place the AP
against the wall where you want to install the AP. Mark the location of
the three screw holes.
5

Figure 2 Screw hole locations and sizes (in mm)
1: Hook
2: Mounting hole
3: Clip
4: Mounting clip
2. Drill three holes for the wall anchors, typically 5 mm (3/16 inch) in
diameter.
3. Insert the anchors and tap them flush with the wall surface.
4. Use the mounting screws to attach the mounting bracket to the wall.
Ø5.0
40.0
103.0
86.0
136.0
12
4
3
6

Figure 3 Installing the wall-mounting bracket
1: Wall-mounting bracket
2: Hook
3: Clip 4: Screw, Length ( 17.4mm / 0.69in ),
Wrench size ( 6.5mm / 0.26in ), Thread size
( 3.5mm /0.14in )
5. Connect the Ethernet cable to the AP.
6. Align the AP mounting hook holes with the hooks on the AP bracket.
7. Push the AP onto the mounting bracket, and then slide it down until it is
fully engaged.
123
4
7

Figure 4 Mounting the AP to the wall mounting bracket
Mounting the AP on a suspended
ceiling
The AP can be mounted on a suspended ceiling by using a T-rail holder.
Note: The width of the T-rail must be in the range of 16 mm to 28 mm (0.63
in to 1.10 in).
1. Loosen the four M3 screws (7) on the clip holders (3).
1
2
8

Figure 5 T-rail holder
1: T-rail clip
2: M3 screw nut
3: M4 screw nut
4: Clip holder
5: T-rail holder
6: Mounting hook
7: M4 × 5 screw, Length ( 7.6mm /
0.3in ), Wrench size ( 7mm / 0.28in ),
Thread size ( 4mm / 0.16in )
8: M3 × 8 screw, Length ( 10mm /
0.39in ), Wrench size ( 5.5mm /
0.22in ), Thread size ( 3 mm /
0.12in )
2. Slide the T-rail clips away from the T-rail holder until the opening is wider
than the T-rail (arrow 1).
Figure 6 Attaching the T-rail holder to the T-rail
13
4
6
7
8
2
5
1 2
9

3. Attach the T-rail holder to the T-rail, slide the T-rail clips toward the T-rail
holder until it closes around the T-rail (arrow 2), and then tighten the M3
screws.
4. Verify that the T-rail holder is firmly attached to the T-rail.
5. Hook the mounting bracket clip (3) to the T-rail holder mounting hook
(2).
6. Use the two M4 screws (1) to attach the mounting bracket to the T-rail
holder, and verify that the bracket is firmly anchored to the T-rail.
Figure 7 Mounting the AP to the T-rail
1: M4 × 5 screw, Length ( 7.6mm /
0.3in ), Wrench size ( 7mm / 0.28in ),
Thread size ( 4mm / 0.16in )
2: Mounting hook
1
2
3
4
10

3: Mounting clip
4: Hook
7. Attach the AP to the wall-mounting bracket. For more information, see
"Mounting the AP on a wall."
Mounting the AP on a ceiling tile
You can mount the AP on a ceiling tile if the ceiling tile is less than 18 mm
(0.71 in) and is able to bear a minimum weight of 5 kg (11.02 lb).
Caution: Do not mount the AP on a ceiling that is made of low-intensity
material such as plaster. If you need to mount the AP to such a ceiling, put a
high-intensity plate beneath the ceiling to secure the installation.
1. Hold the mounting bracket up against the ceiling tile where you want to
install it. Mark the location of the screw holes.
2. Drill three 5.0 mm (3/16 inch) holes in the ceiling tile.
3. Insert the hex-head bolts into the mounting bracket screw holes and
through the holes in the ceiling tile.
4. Fasten the washers and hex nuts to the hex-head bolts on the other side
of the ceiling tile.
Figure 8 Attaching the mounting bracket to a ceiling
1: Nut, Length ( 4.5mm /0.18in ),
Diameter ( 10mm / 0.39in)
2: Washer
3: Ceiling
4: Wall-mounting bracket
1
3
5
6
4
2
11

5: Hex-head bolt, Length ( 32mm /
1.26in ), Wrench size ( 6.85mm /
0.27in ), Thread size ( 3.91mm / 0.15in )
6: Hook
5. Attach the AP to the wall-mounting bracket. For more information, see
"Mounting the AP on a wall."
Removing the AP
To remove the AP from the bracket, insert a straight-edge screwdriver on
either side of the AP (in line with either the 2.4 GHz-2 or 5 GHz-2 antenna
ports) between the bracket and the clip. Rotate the screwdriver slightly so that
the clip flexes away from the bracket, and then slide the AP toward the
narrow end of the mounting bracket until the AP is released. Be sure to firmly
grip the AP so that it does not fall.
Technical support
For worldwide technical support information, see the HP support website at
www.hp.com/networking/support.
Other regulatory information
For important safety, environmental, and regulatory information, see Safety
and Compliance Information for Server, Storage, Power, Networking, and
Rack Products, available at
www.hp.com/support/Safety-Compliance-EnterpriseProducts.
FCC Notice
This device must not be co-located with any other transmitters except in
accordance with FCC multi-transmitter product procedures.
Referring to the multi-transmitter policy, multiple-transmitter(s) and module(s)
can be operated simultaneously without C2P.
12

A 20 cm minimum distance must be maintained between the antenna and the
users for the host this module is integrated into. Under such configuration, the
FCC radiation exposure limits set forth for a population/uncontrolled
environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer
could void the user's authority to operate this equipment.
Industry Canada Notice
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Important Note: IC Radiation Exposure Statement: This equipment
complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body.
Remarque importante - Déclaration d’exposition aux radiations : Cet
équipement est conforme aux limites d’exposition aux rayonnements IC
RSS-102 établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé en gardant une distance minimale de 20 cm entre le
système radiant et vous.
Notice for Brazil, Aviso aos usuários no
Brasil
Este equipamento opera em caráter secundário, isto é, não tem direito a
proteção contra interferência prejudicial, mesmo de estações do mesmo tipo,
e não pode causar interferência a sistemas operando em caráter primário.
13

Notice for Mexico, Notificación México
La operación de este equipo está sujeta a las siguientes dos condiciones: (1)
es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo
la que pueda causar su operación no deseada.
Notice for Korea
B 급기기
( 가정용 방송통신
기자재
)
이기기는 가정용 (B 급) 전자파 적합기기로서주
로가정에서 사용하는 것을 목적으로 하며 , 모든
지역에서 사용할 수있습니다 .
Class B (broadcasting
communication
device for home use)
This device obtained EMC registration mainly for
home use (Class B) and may be used in all areas.
해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는
할수없음
Notice for Taiwan
低功率電波輻射性電機管理辦法
第十
二條
經型式認證合格之低功率射頻電機，非經許
可，公司、商號或使用者均 不得擅自變更頻
率、加大功率或變更原設計之特性及功能
第十
四條
低功率射頻電機之使用不得影響飛航安全
及干擾合法通信；經發現有干 擾現象時，應
立即停用，並改善至無干擾時方得繼續使
用。前項合法通 信，指依電信法規定作業之
無線電通信。低功率射頻電機須忍受合法通
信或工業、科學及醫療用電波輻射性電機設
備之干擾。
在5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。
無線資訊傳輸設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上
所述正常操作，發射的信號應維持於操作頻帶中。
電磁波曝露量 MPE 標準值 1mW/cm2，送測產品實測值為: XXXXX mW/cm2。
14

Eurasian Economic Commission
Евразийская экономическая комиссия
Еуразиялықэкономикалықкомиссия
Євразійська економічна комісія
HP 525 Wireless Dual Radio 802.11ac
Access Point (JG994A)
Беспроводная точка доступа с двумя
радиомодулями HP 525 Wireless Dual
Radio 802.11ac Access Point (JG994A)
HP 525 Wireless Dual Radio 802.11ac
кіру нүктесі (JG994A)
Точка доступу HP 525 із двома
радіомодулями 802.11ac (JG994A)
(RMN BJNGA-FB0004)
15

Manufacturer
Производитель
Өндіруші
Виробник
Hewlett-Packard Company, 3000 Hanover
Street, Palo Alto, California 94304-1185, U.S.A
Made In China
Изготовлено в Китае
Қытайда жасалған
Виготовлено в Китаї
Local Representatives
Местные представители
Жергілікті өкілдері
Місцеві представники
HP Russia: ЗАО «Хьюлетт-Паккард А.О.», 125171, Россия,
Москва, Ленинградское шоссе, 16А, стр. 3
Тел./факс: [phone]
HP Belarus: ИООО «Хьюлетт-Паккард Бел», 220030,
Беларусь, г. Минск, ул. Интернациональная, 36-1
Тел./факс: [phone]
HP Kazakhstan: ТОО «ХЬЮЛЕТТ-ПАККАРД (К)», 050040
Республика Казахстан, г. Алматы, ул. Тимирязева 28В,
бизнес-центр «Алатау Гранд», 1й этаж
Тел./факс: [phone]
HP Kazakhstan: ЖШС «Хьюлетт-Паккард (К)», 050040,
Қазақстан, Алматы қ., Бостандықауданы, Тимирязев к-сі, 28В,
тел./факс: [phone]
16

Product overview
The AP supports two radios: 802.11ac/n/a on Radio 1 and 802.11n/b/g on
Radio 2 with 2x2 MIMO two spatial stream. The AP has two auto-sensing
10/100/1000 Base-T Ethernet ports (RJ45), a standard console (serial) port
(RJ-45), two 2.4 GHz antenna ports, two 5 GHz antenna ports and a 48 VDC
power port.
Обзор продукта
Точка доступа поддерживает два радиомодуля: первый работает по
стандарту 802.11ac/n/a, второй по стандарту 802.11n/b/g с технологией
2x2 MIMO (два пространственных потока). Точка доступа оснащена
двумя портами 10/100/1000 Base-T Ethernet (RJ45) с автоматическим
определением полярности, стандартным последовательным портом
консоли (RJ-45), двумя портами для антенны 2,4 ГГц, двумя портами для
антенны 5 ГГц и портом питания 48 В пост. тока.
Өнімге жалпы шолу
Кіру нүктесі екі радиосына қолдау көрсетеді: 1-ші сымсыз радионың
стандарты – 802.11ac/n/a және 2-ші сымсыз радионыңстандарты –
802.11n/b/g (2 x 2 MIMO екі кеңестік жолы бар). Кіру нүктесінің
автоматты түрде анықтайтын екі 10/100/1000 Base-T Ethernet порты (RJ45),
стандартты басқару (тізбекті) порты (RJ-45), екі 2,4 ГГц антенна ұясы, екі 5
ГГц антенна ұясы және 48 Втұрақты токтыңқуат ұясы бар.
Огляд продукту
Точка доступу підтримує два радіомодулі: радіомодуль 1 зі стандартом
802.11ac/n/a та радіомодуль 2 зі стандартом 802.11n/b/g з двома
просторовими потоками 2x2 MIMO. Точку доступу оснащено двома
портами 10/100/1000 Base-T Ethernet (RJ45) з автоматичним
розпізнаванням швидкості, стандартним консольним (серійним) портом
(RJ-45), двома антенними портами з частотою 2,4 ГГц, двома антенними
портами з частотою 5 ГГц і портом живлення для джерела з напругою
48 В постійного струму.
17

Manufacturing date
The manufacturing date is defined by the serial number.
CCYMBBBZZZ (HP serial number format for this product)
Valid date formats include:
•
Y (Y) = Year of Manufacture (Where Yindicates the year counting from
within each new decade, with 2000 as the starting point. For example, 2
for 2002. The year 2010 is indicated by 0, 2011 by 1, and so forth. YY
indicates the year using a base year of 2000. For example, 02 for 2002
and 12 for 2012)
•
M (M) = Month of Manufacture (For M, 1-9 for January to September, 0
for October, A for November, B for December. For MM, actual calendar
month 1-12 )
Дата изготовления
Дата изготовления определяется по серийному номеру.
CCYMBBBZZZ (формат серийных номеров HP для данного изделия)
Действительные форматы даты:
•
Y (Y) = год производства (где Yобозначает год, отсчитываемый в
каждом новом десятилетии, начиная с 2000. Например, 2 для 2002.
Для обозначения 2010 используется 0, для 2011 – 1 и т. д. YY
обозначает год, при этом базовым годом является 2000. Например, 02
обозначает 2002, 12 обозначает 2012)
•
M (M) = месяц производства (где для Mцифры с 1 по 9 обозначают
месяцы с января по сентябрь соответственно, 0 обозначает октябрь, A –
ноябрь, B – декабрь. MM обозначает календарный месяц с 1 по 12)
Өндірілген күні
Өндірілген күні сериялықнөмір арқылы анықталады.
CC
YM
BBBZZZ (Осы өнімге арналған HP сериялықнөмірі)
Жарамды күнпішімдері келесіні қамтиды:
•
Y (Y) = Жасалған жылы (мұнда
Y
әрпі 2000 бастапқынүктесінен
бастап әрбір жаңадекада ішінде есептелетін жылды көрсетеді.
18

Мысалы, 2 саны 2002 жылды көрсетеді. 0 саны 2010 жылды, 1 саны
2011 жылды және т.с.с. 2000 бастапқыжыл болып,
YY
әріптері жылды
көрсетеді. Мысалы, 02 саны – 2002 жылды және 12 саны 2012 жылды
көрсетеді)
•
M (M) = Жасалған айы (мұнда
M
, 1-9 сандары қаңтар мен қыркүйек
аралығындағы айларды, 0 саны қазан айын, A әрпі қараша айын
және B әрпі желтоқсан айын білдіреді. Мұнда
MM
әріптері 1-12
аралығындағы нақты күнтізбе айын білдіреді)
Дата виробництва
Дата виробництва зашифрована в серійному номері.
Формат серійного номера HP для цього продукту: CCYMBBBZZZ
Нижче наведено можливі формати дати виготовлення.
•
Y (Y) — рік виготовлення, де Yуказує на останню цифру року (відлік
ведеться з 2000 р.). Наприклад, 2 позначає 2002 рік, 0 — 2010,
1 — 2011 тощо. YY указують на дві останні цифри року, починаючи з
2000-го. Наприклад, 02 означає 2002 рік, а 12 — 2 012 рік.
•
M (M) — місяць виробництва. Для значення Mможуть
використовуватися цифри або літери: цифри 1–9 позначають місяці із
січня по вересень, 0 — жовтень, A — листопад, B — грудень.
Варіант MM — це традиційне позначення календарного місяця (з 1-го
п о 12-й).
Environmental Conditions
Operating temperature:
32°F to 115°F (0°C to 45°C)
Operating relative humidity:
5% to 95%, noncondensing
Non-operating/Storage
temperature:
–40°F to +158°F (–40°C to
+70°C)
Non-operating/Storage relative
humidity:
5% to 95%, noncondensing
Altitude:
Up to 13,123 ft (4 km)
19

Условия окружающей среды
Рабочая температура:
от 32 до 115°F (от 0 до 45°C)
Относительная влажность при
эксплуатации:
от 5% до 95%, без конденсации
Температура при отсутствии
эксплуатации/при хранении:
от -40 до +158°F (от -40 до +70°C)
Относительная влажность при
отсутствии эксплуатации/при
хранении:
от 5% до 95%, без конденсации
Высота над уровнем моря:
до 13 123 футов (4 км)
Қоршаған орта шарттары
Жұмыс температурасы:
0°C – 45°C (32°F – 115°F)
Жұмыс істейтін салыстырмалы ауа
ылғалдылығы:
5% - 95%, конденсацияланбаған
Жұмыс істемейтін/Сақтау
температурасы:
-40°C пен +70°C (-40°F пен
+158°F)
Жұмыс істемейтін/Сақтау
салыстырмалы ауа ыл
ғ
алдылы
ғ
ы: 5% - 95%, конденсацияланбаған
Биіктік:
4 км-ғадейін (13 123 фут)
Умови експлуатації
Температура (робоча): від 0 до 45 ℃ ( ві д32 до 115 ℃)
Відносна вологість (робоча): від 5 до 95% (без конденсації)
Температура (неробоча/для
зберігання):
від –40 до +70 °C (від –40 до
+ 158 °F)
Відносна вологість (неробоча/для
зберігання): від 5 до 95% (без конденсації)
20