Huawei nova 2 Quick start guide

・ In this manual, "Setting Guide", "Basic Manual", and
"Notes on Usage" are collectively referred to as
"Instruction Manual".
・ In this manual, HUAWEI nova 2 HWV31 is usually
referred to as "HWV31", "the product", or "main unit".
・ In this manual, "microSD™ memory card
(commercially available)", "microSDHC™ memory card
(commercially available)", and "microSDXC™ memory
card (commercially available)" are abbreviated as
"microSD memory card" or "microSD".
Notes on Usage
HWV31
February 2018, 1st Edition - 1 - - 2 - - 3 - - 4 - - 5 -
- 6 - - 8 -- 7 - - 9 - - 10 - - 11 -
- 12 - - 13 - - 15 -- 14 - - 16 - - 17 -
Using the Product
Before you start using the product, be sure to read "Safety
Precautions" in this manual to ensure correct use.
Before you assume that the product is malfunctioning,
perform "トラブル診断" (Trouble check). (Displayed language
is Japanese only.)
Home screen→[au]→[故障紛失サポート] (Repair and
Delivery Service)→[トラブル診断] (Trouble check)
(Displayed language is Japanese only.)
Or, check for possible remedies in the following site "トラブ
ル診断" (Trouble check) of au homepage:
https://www.au.com/trouble-check/
• Communication is not possible even inside the service
area in places where the signal does not reach (e.g.
tunnels and basements). Also, communication is
sometimes not possible in poor reception areas.
Communication is sometimes interrupted if you move
into poor reception areas during communications.
• Since this product uses radio waves, the possibility
of communication intercepts by third parties cannot
be eliminated. (Though LTE/WiMAX 2+/GSM/UMTS
system has highly secure condential communication
features.)
• VoLTE (LTE network) by au is used when connecting
with emergency call receiving agencies within Japan.
You cannot connect through 3G (circuit switching
network).
• The product is compatible with au World Service.
Each network service described in this manual varies
depending on the area and service content.
• The product is compatible with au World Service.
Each network service described in this manual varies
depending on the area and service content.
• Since this product is a radio station under the Radio
Law, you may be asked to temporarily submit the
product for inspection in accordance with the Radio
Law.
• IMEI information of your cell phone is automatically sent
to KDDI CORPORATION for maintenance and monitoring
operational status of your cell phone.
• Before you start using the product overseas, check the
relevant laws and regulations of the country/region you
visit.
• The Company is not liable for any damages arising from
earthquakes, lightning, storms, oods or other natural
disasters, as well as res, actions by third parties, other
accidents, intentional or mistaken misoperation by the
customer, or use under other unusual conditions outside
the responsibility of the Company.
• The Company is not liable for any incidental damages
(change/disappearance of described content, loss of
business income, disruption of business, etc.) arising
from use or inability to use the product.
• The Company is not liable for any damages arising
from failure to observe the described content of "Basic
Manual" and "Notes on Usage" (this manual).
• The Company is not liable for any damages arising,
for example, from malfunction caused by combination
with connected devices or software not related to the
Company.
• Captured image data or downloaded data may
sometimes be altered or lost due to faults, repair or
other handling of the product. The Company is not liable
for any damage or lost income resulting from recovery
of these data.
• It is recommended you keep a copy of important data
on your PC's hard disk, etc. Whatever the cause of
fault or malfunction may be, the Company assumes no
responsibility for alteration or loss of saved information.
• Contents saved in the product, such as contacts, mails
and favorites, might be altered or lost by an accident,
fault, repair or mishandling. Be sure to keep a copy of
important contents. Note that Company assumes no
responsibility for any damages or lost prots resulting
from altered or lost contents.
• Note that content data (both charged or free of charge)
saved on the product cannot be returned to the
customer when the product is replaced for repair of a
fault, for example.
• This product uses liquid crystal for its display. The
display response speed may become slow when
the ambient temperature is low, which is due to the
property of liquid crystal and not a malfunction. The
display response speed will return to normal at room
temperature.
• Although the display used on the product is made using
high-precision technology, some pixels (dots) might be
lit or out at all times. This is not a malfunction.
• You are recommended to store copies of individual data
such as photos you took, videos and music in your PC
by sending each le as mail attachment, etc. Note,
however, that you may not be able to make copies of
some copyrighted data even by the above-mentioned
means.
• Do not discard the product together with regular trash.
Please cooperate in the collection of the product
(including optional products) when it is no longer
needed to protect the environment and e󱐯ectively use
resources. Old product is collected at au shops and
other places.
* "The Company" as appears in this manual refers to the
following companies:
Sold by: KDDI CORPORATION, OKINAWA CELLULAR
TELEPHONE COMPANY
Imported by: HUAWEI TECHNOLOGIES JAPAN K.K.
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD.
◎ Reproduction of the content of this manual in part or
in whole is prohibited.
◎ The content of this manual is subject to change
without notice.
◎ Some functions may become unavailable due to
the change of the specications of the operating
systems, and change or termination of services.
◎ Every e󱐯ort has been made in the preparation of
this manual. Should you notice any unclear points,
omissions, etc., feel free to contact us.
Safety Precautions (Always
follow these directions)
■Before using this product, thoroughly read these
"Safety Precautions" for proper use. After reading
this manual, keep it carefully.
■These precautions contain information intended to
prevent bodily injury to the user and to surrounding
people, as well as damage to property, and must
be observed at all times.
■The following symbols indicate the di󱐯erent
degrees of injury or damage that may occur if
information provided is not observed and the
product is used improperly.
This symbol indicates the "potential
and imminent danger of death or
serious injury*1 to a person" due to
mistaken handling.
This symbol indicates the
"possibility of death or serious
injury*1 to a person" due to mistaken
handling.
This symbol indicates the
"possibility of personal minor injury*2
to a person" or physical damage*3"
due to mistaken handling.
*1 Serious injury: This refers to loss of sight, injury, burns
(high- and low-temperature), electric shock, broken
bones, injury with residual aftere󱐯ects from poisoning,
etc., and injuries requiring hospital admission for
treatment or long term hospital attendance as an
outpatient.
*2 Minor injury: This refers to injuries, burns (high- and low-
temperature), electric shock, etc. that do not require
hospital admission for treatment or log-term hospital
attendance as an outpatient.
*3 Physical damage: This refers to extended damage to
buildings, furniture, livestock or pets.
■Explanation of Prohibition or Enforcement Symbols
Don’t
Indicates an
action that is not
allowed.
No
wet hands
Indicates that
handling with
wet hands is not
allowed.
Not
disassembly
Indicates that
disassembly is
not allowed.
Do
Indicates that
instructions
specied are
compulsory (must
be followed).
Not liquids
Indicates
that use in a
place where
the product is
likely to get
wet or allowing
the product to
get wet is not
allowed.
Unplug
power plug
Indicates that the
power plug must
be disconnected
from the power
outlet.
■Precautions common to the main unit, internal
battery, charging equipment, au IC Card, peripheral
devices
Don’t
Do not use, store or leave the product in
hot places or places where heat is easily
accumulated (e.g. by the re, near a heater,
under a kotatsu, in direct sunlight, in a car in
the hot sun).
Doing so may cause re, burns, injuries, or electric
shock.
Don’t
Do not put the product in, or place it near a
cooking apparatus such as microwave oven or
IH cooker, or a high-pressure container such
as pressure vessel.
Doing so may cause re, burns, injuries, or electric
shock.
Don’t
Do not expose to or place directly on sand,
dirt, or mud. Do not handle with dirty hands.
Doing so may cause re, burns, injuries, or electric
shock.
Don’t
Do not charge the equipment when wet with
water or other liquid (drinking water, sweat,
seawater, pet urine, etc.).
Doing so may cause re, burns, injuries, or electric
shock.
Don’t
Do not subject the product to strong pressure
or break the product. Especially when bringing
the product putting in a pocket of clothes, do
not let the product hit against surroundings or
being put between the objects.
Doing so may cause re, burns, or injury due to
battery damage.
* Examples to avoid
• Sitting or squatting with the product put in a
pocket of trousers or skirt
• Putting the product in a pocket of outer wear
and catching them in a door or a door of car
• Stepping on the product on a soft object such
as a sofa, bed, or bedding, or on a oor
Not
disassembly
Do not disassemble or modify the product.
Doing so may cause re, burns, injuries, or electric
shock.
Not liquids
Do not get the product wet with water or other
liquid (drinking water, perspiration, seawater,
urine of pet animals, etc.).
Doing so may cause re, burns, injuries, or electric
shock.
Not liquids
Do not allow water or other liquids (drinking
water, perspiration, seawater, urine of pet
animals, etc.) to get inside the external
connection terminal.
Doing so may cause re, burns, injuries, or electric
shock.
Do
Use only optional products specied by au.
Not doing so may cause re, burns, injuries, or
electric shock.
Don’t
Do not subject the product to strong force,
shock or vibration by dropping, stepping on, or
throwing the product.
Doing so may cause re, burns, injuries, or electric
shock.
Don’t
Do not allow conductive materials (metal
pieces, pencil lead, etc.) to come in contact
with the external connection terminal, and do
not allow dust to get inside.
Doing so may cause re, burns, injuries, or electric
shock.
Don’t
Do not cover or wrap the product with a
blanket, etc. while using or charging.
Doing so may cause re or burns.
Do
If charging is not completed after the specied
charging time, stop charging.
Doing so may cause re, burns, or injury due to
overcharging.
Do
Before entering an area where ammable gas
is generated such as a gas station, or an area
where dust is generated, always be sure to
turn o󱐯 the product, and discontinue charging
the product if charging.
Using the product where ammable gas is
generated may cause explosion or re.
Do
If you notice anything unusual, such as an
unusual odor, noise, smoke, overheating,
discoloration or deformation during use,
charging or storage, follow the instructions
below.
• Unplug the power plug from the power outlet.
• Turn the product o󱐯.
Not doing so may cause re, burns, injuries, or
electric shock.
Don’t
Do not use the damaged product.
Doing so may cause re, burns, or injuries.
Don’t
Do not place the product on unstable places
such as rocky stands or tilting surfaces. Be
careful especially while the vibrator is set.
Doing so may cause the product to fall and cause
injuries.
Don’t
Do not store or use the equipment in locations
that are subject to humidity, dust or high
temperatures.
Doing so may cause re, burns, or electric shock.
Don’t
If being used by a child, have a guardian teach
him/her the proper handling procedure, and do
not allow improper use.
Doing so may cause injuries.
Don’t
Do not leave in places within the reach of
small children.
Doing so may cause accidental swallowing,
injuries, or electric shock.
Do
The product may reach a high temperature
when using it continuously for a long time or
when charging it. Also avoid falling asleep and
unintentionally having prolonged contact with
the product.
The product, internal battery, or adapter may
become hot when using the product for a long
time such as when using applications, calling,
performing data communication, watching videos,
or while charging. Directly touching a warmed part
for a long time may cause redness, itching, rashes,
etc. on your skin, or result in low-temperature burns
depending on your constitution or health condition.
■Main unit
Don’t
Do not throw the product into a re or heat it.
Doing so may cause re, burns, or injuries.
Don’t
Do not apply excessive force on the product
such as by puncturing it (sharp object), hitting
it with a hammer (hard object) or stepping on
it.
Doing so may cause re, burns, or injuries.
Do
If the substance inside the product comes into
contact with your eyes or mouth, immediately
rinse the area with clean water, and then see
a doctor right away.
Not doing so may cause loss of sight or poor
physical condition due to the inuence of the
substance, etc. inside the product.
Don’t
Do not lighten or illuminate the ash/photo
light with the light-emitting part pointed at the
someone’s eyes. Especially when you use
it for young children, keep su󱐰cient distance
from them.
Doing so may cause impairment of eyesight, etc.
Also, eyesight may be temporarily a󱐯ected or they
may be surprised, leading to an accident.
Don’t
Do not lighten or illuminate the ash/photo
light to point at the eyes of someone driving a
car, etc.
Doing so hinder driving and may cause an
accident.
Don’t
Do not view a repeatedly ickering screen for
a prolonged period.
May cause spasms, loss of consciousness, etc.
Don’t
Do not allow water or other liquids (drinking
water, perspiration, seawater, urine of pet
animals, etc.), metal pieces, ammable
material or foreign object into the au IC Card/
microSD memory card slot on the product.
Note the correct locations and orientations
for inserting au IC Card and microSD memory
card.
Doing so may cause re, burns, injuries, or electric
shock.
Don’t
Do not expose the camera lens to direct
sunlight for an extended period.
Doing so may cause re, burns, or injury due to
concentration of light.
Do
Turn o󱐯 the product or put it in the Airplane
mode before boarding an airplane.
Since using the product on airplanes is restricted,
follow the instructions given by the respective
airlines.
The product's signals may adversely a󱐯ect on-
board electronic equipment.
Prohibited acts related to product usage on an
airplane may be punished by law.
Do
When using in hospitals, follow the guidelines
of each institution.
Turn power o󱐯 where use is prohibited.
The product's signals may a󱐯ect electronic
equipment and electronic medical equipment.
Do
When using the handsfree call, ringtone is
ringing, or in the standby mode, be sure to
keep the product o󱐯 of the ears.
When you attach the earphone/microphone
etc. to the handset to play games, videos,
music, etc., do not make the volume too loud.
When using the handsfree call, loud noise sounds
from the product.
Even in the standby mode, ringtone and alarm may
work suddenly.
Using continuously for a long time with too loud
volume may cause a hearing loss, etc.
And, if you cannot hear the sound around you
clearly, it may cause an accident.
Do
If you have a weak heart, set the vibrator or
ringtone volume carefully.
Sudden ringtone vibration and ringtone surprise
you, and it may cause harmful e󱐯ect on heart.
Do
If you are using electronic medical equipment
etc., contact the respective manufacturer or
dealer to check whether the operation of the
equipment is a󱐯ected by signals.
Not doing so may cause harmful e󱐯ect on
electronic medical equipment, etc. due to radio
wave.
Do
Turn the product o󱐯 near high-precision
electronic control equipment or electronic
equipment using low-power signals.
Not doing so may cause the equipment to fail or
malfunction due to radio wave.
* Take particular care with the following devices
Hearing aids, implanted cardiac pacemakers,
implanted cardioverter-debrillators or other
electronic medical equipment, and other
equipment controlled by electronic signals, etc.
If you use an implanted cardiac pacemaker,
implanted cardioverter-debrillator or other
electronic medical equipment, contact the
manufacturer or dealer to check whether the
operation of the equipment is a󱐯ected by
signals.
Do
If the Glass or camera lens is damaged, be
careful of broken glass and the exposed inside
of the product.
Touching the damaged or exposed area may cause
re, burns, injuries, or electric shock.
Do
Stop using the product immediately and move
the internal battery away from re if you notice
leakage of substance, etc. inside the internal
battery or unusual odor.
The battery uid is ammable and could ignite,
causing a re, explosion, etc.
Do
Be careful not to have the product bitten by
your pet, etc.
Not doing so may cause re, burns, or injuries
due to ignition, rupture, or overheat of the internal
battery, or leak from it.
Don’t
For using a motion sensor, check the safety
around, hold the product and do not swing it
more than necessary.
Doing so may cause injuries or other accidents.
Don’t
If the display breaks and the uid, etc. leaks
out from inside, do not let the uid contact
with the skin on your face or hands or clothes.
Doing so may cause eye or skin problems.
If the internal matter etc. comes into contact with
your eyes, mouth, skin or clothes, immediately
rinse the contacted area with clean water.
If the uid, etc. enters your eyes or mouth,
immediately see a doctor after rinsing.
Don’t
Do not discard the product together with
regular trash.
Doing so may cause re, burns, or injuries. Doing
so may cause environmental degradation. Take
the unnecessary product to a sales outlet such
as an au shop or follow the instructions by a local
institution that handles used products.
Don’t
If uid, etc. leaks out from the internal battery,
do not let the uid contact with the skin on
your face or hands or clothes.
Doing so may cause eye or skin problems.
If the internal matter etc. comes into contact with
your eyes, mouth, skin or clothes, immediately
rinse the contacted area with clean water.
If the uid, etc. enters your eyes or mouth,
immediately see a doctor after rinsing.
Do
Be careful with the tip of the SIM card removal
tool (sample) not to injure any part of your
body (ngers, etc.) when you remove au IC
Card or microSD memory card.
Touching the tip of the SIM card removal tool
(sample) may cause injuries.
Do
If you use the handset in a vehicle, contact
the vehicle manufacturer or dealer to check
whether the operation of the vehicle is
a󱐯ected by signals.
In rare cases, using the phone in some vehicle
models can cause the vehicles electronic
equipment to malfunction. In that case, stop using
the product immediately.
Do
If use of the product causes any skin
abnormalities, immediately stop using the
product and seek medical treatment.
Itching, rashes, eczema, etc. sometimes occurs
depending on your physical constitution and
condition.
For the materials of each part→P18
Do
The speaker and camera of the product use
magnetic components. Make sure that metal
objects (cutter blades, staples, etc.) are not
attached to it.
Attached objects may cause bodily injury, etc.
Do
Look at the display in a well-lit place, keeping
a certain distance from the screen.
Viewing in a dark location or too closely may a󱐯ect
your eyesight.
■Charging equipment
Don’t
Do not use if the cord of the adapter or USB
cable is damaged.
Doing so may cause re, burns, or electric shock.
Don’t
Do not use the adapter and USB cable in
humid locations such as a bathroom.
Doing so may cause re, burns, or electric shock.
Don’t
Do not touch the adapter or USB cable if you
hear thunder.
Doing so may cause electric shock.
Don’t
Do not short-circuit the external connection
terminal when connected to an outlet. Do
not allow any part of your body such as your
hands or ngers to come into contact with the
external connection terminal.
Doing so may cause re, burns, or electric shock.
Don’t
Do not apply excessive force on the cord of
the adapter or the USB cable by placing heavy
objects on it or by pulling it.
Doing so may cause re, burns, or electric shock.
Don’t
When plugging/unplugging an AC adapter
into/from the outlet, do not allow metallic
objects to come into contact with the prongs
of the plug.
Doing so may cause re, burns, or electric shock.
Don’t
Do not use a travel converter instead of the
AC adapter.
Doing so may cause re, overheating, electric
shock.
Don’t
Do not apply excessive force where the
adapter is connected to the product.
Doing so may cause re, burns, injuries, or electric
shock.
No
wet hands
Do not handle the cord of the adapter, USB
cable, the external connection terminal, or
power plug with wet hands.
Doing so may cause re, burns, or electric shock.
Do
Always use the specied power supply and
voltage.
When using overseas, use the AC adapter
that is available overseas.
Using the incorrect power supply or voltage may
cause res, burns, electric shock, etc.
AC adapter: AC100V (Connect only with a
household AC outlet) AC adapter available
overseas: AC100V to 240V (Connect only with a
household AC outlet)
Do
Wipe o󱐯 any dust on the power plug.
Using the power plug with dust may cause res,
burns, electric shock, etc.
Do
Fully plug the adapter into the outlet.
Not fully plugging the adapter in may cause res,
burns, electric shock, etc.
Do
Always grasp the adapters when unplugging
the power plug from the outlet. Do not pull or
otherwise apply excessive force on the cord of
the adapter or the USB cable.
Pulling the cord may damage it, causing re, burns,
electric shock, etc.
Do
When plugging/unplugging an adapter into/
from the product, plug/unplug the adapter
straight on with the connecting terminal. Do
not pull or otherwise apply excessive force on
the cord.
Not plugging/unplugging correctly may cause
res, burns, bodily injury or electric shock.
Do
If the external connection terminal is bent or
otherwise deformed, immediately discontinue
use. Do not use even if terminals are bent
back.
Short-circuited external connection terminal may
cause res, burns, bodily injury, electric shock, etc.
Unplug
power plug
When not in use, unplug the adapter from the
outlet.
Leaving the power plug plugged may cause re,
burns, or electric shock.
Unplug
power plug
Immediately unplug the power plug from the
outlet if water or other uids (drinking water,
perspiration, seawater, urine of pet animals,
etc.) get on the charging equipment.
Short-circuit due to attached objects may cause
re, burns, or electric shock.
Unplug
power plug
Always unplug the power plug from the outlet
before cleaning the charging equipment.
Cleaning while still plugged in may cause res,
burns or electric shock.
Don’t
Do not touch the adapter for a long time when
connected to an outlet.
Doing so may cause burns etc.
■au IC Card
Do
Be careful not to scratch yourself (nger, etc.)
with the cut section when handling au IC Card.
The cut surface may be sharp, and it may cause
injuries.
■For use near medical equipment and in medical
institutions
Do
Those with an implanted pacemaker or
implanted cardioverter-debrillator should carry
or use the product at least 15 cm away from
the pacemaker or cardioverter-debrillator.
Not doing so may cause harmful e󱐯ect on
electronic medical equipment due to radio wave.
Do
When using electronic medical equipment
other than an implanted pacemaker and
implanted cardioverter-debrillator outside
a medical institution (e.g. home medical
treatment), check individually with the
manufacturer of the electronic medical
equipment regarding the inuence of radio
waves.
Not doing so may cause harmful e󱐯ect on
electronic medical equipment due to radio wave.

- 22 - - 23 -
- 24 - - 25 - - 26 - - 27 - - 29 -- 28 -
- 31 - - 32 - - 33 - - 34 - - 35 -
- 21 -- 18 - - 19 - - 20 -
- 30 -
●Using or charging the product in the bag or with it
covered by bedding etc. may cause malfunction.
●When using charging equipment or external device,
insert/remove the connector straight to/from the
product. If the connector is inserted/removed in
an incorrect orientation or direction, it may cause
malfunction.
●Do not expose the camera lens to direct sunlight for an
extended period. Doing so may cause malfunction.
●Do not store or leave the product in places subject to
direct sunlight (e.g. in automobiles), places that get
hot, places that get extremely cold, or in humid or dusty
places. Doing so may cause malfunction.
●Do not place the product on unstable places such as
rocky stands or tilting surfaces. Be careful especially
while the vibrator is set. Doing so may cause the
product to fall, leading to malfunction, etc.
●For charging the product, do not exceed the rating of
an outlet or wiring device by overloading an electrical
circuit, etc.
■Main unit
●The product's battery is built in, and cannot be replaced
by the customer. For battery replacement, contact an
au shop or Customer Service Center.
●Do not forcefully press, tap or intentionally subject
the display to strong impact. Doing so may cause
scratching or damage.
●Do not forcefully press your ngernails, sharp objects or
hard objects against buttons or display surface. Doing
so might cause scratching or damage.
●The touch panel is designed to be lightly touched by
ngers. Do not apply strong pressure with your ngers
or sharp-pointed objects (such as ngernails, ballpoint
pens and pins) on the touch panel.
●Never use the product that is modied. Use of
a modied device violates the Radio Law and
Telecommunication Business Act. The product
is compliant with rules on the technical standard
conformance of specied wireless equipment based on
the Radio Law/Telecommunications Business Act, and
as a proof of it, the "Technical Conformity Mark " is
checkable on the product.
<<Checking procedure>>
Home screen→[基本フォルダ] (Basic
folder)→[Settings]→[About phone]→[Certication]
If the product is disassembled and modications are
made to the internal components, the certication of
conformity with technical regulations will become invalid.
Never use the product with the certication invalid, as it
is a violation of the Radio Law and Telecommunications
Business Act.
●Take care not to place magnetized items such as
magnetic cards, speakers and TV sets near the
product, as it may cause malfunction.
Putting a strong magnetism close to the product may
cause false operation.
●Do not bring the product close to magnetic cards such
as cash cards, credit cards, and prepaid cards. Doing
so may result in loss of recorded information.
●When you put the product in your pocket or bag, take
care so that the display does not come in contact
with metal objects or other hard objects, as it may
cause scratching or damage. Doing so might cause
scratching or damage. Also, be aware that any metal
or other hard object that comes into contact with the
display may scratch or damage them.
●When suddenly brought into a warm place from a
cold place, or when in a humid location, or when used
where temperature suddenly changes (e.g. near the
air discharge port of an air conditioner), water droplets
(i.e. condensation) sometimes are formed inside
the product. Note that when used under conditions
such as this, the humidity might cause corrosion or a
fault.
●While writing/reading data to/from a microSD memory
card, do not subject the product to vibration or impact,
or turn o󱐯 the power. Doing so may cause data loss or
malfunction.
●Do not cover the illuminance sensor with your nger
or put a sticker on it. Doing so may hinder the sensor
for detecting the ambient light level and functioning
correctly.
●Do not put a sticker, etc. on the proximity sensor. Doing
so may cause the sensor to malfunction and make the
display always turned o󱐯 while receiving a call or during
a call.
●Use the product with the au IC Card/microSD memory
card tray closed. If the tray is open, dirt or water may
get inside, causing malfunction.
●Do not allow liquids, metal objects, and other foreign
matter to get inside the au IC Card/microSD memory
card slot of the product. Doing so may cause
malfunction.
●Do not subject to strong impact to the product such
as dropping, throwing, or stepping on it. Doing so may
cause malfunction.
●Do not place the product directly on sand at a beach,
etc. Sand or other small particles may get inside the
receiver, mouthpiece, speaker, etc. causing the volume
to drop. If sand gets inside the product, it may cause
malfunction.
■Touch panel
●Putting stickers or sheets (e.g. commercially available
protective lms, peep prevention sheets) on the display
might cause incorrect operation of the touch panel.
●When carrying the product in your pocket or bag, take
care not to put the touch panel close to metals or other
conductive materials, as it might cause false operation
of the touch panel.
■Internal battery
Li-ion00
(The internal battery of the product is a
lithium-ion battery.)
The internal battery is not fully charged at
the time of purchase.
Charge the battery before using the
product. Also charge the battery before
using the product if you have not used the
product for a long time.
●Using the product in very hot or cold environments, for
example, when left in an automobile with the windows
closed in summer, will cause the internal battery
capacity to drop and shorten the available battery
usage time. This also shortens the internal battery's
service life. Try to use the internal battery as far as
possible at room temperature.
●After the internal battery is charged, battery power
decreases bit by bit even if the product is not used.
The internal battery may be discharged if the product is
not used for a long time. We recommend to charge the
product before use.
●Internal battery is a consumable item. If the
performance of an internal battery does not recover
(e.g. the usable time after each charge has become
extremely short), the internal battery is at the end of
service life, so stop use. Since the battery is built-in, au
Shop will keep the product and charges will be incurred
for repair. You may not use the product for a certain
period. Please be forewarned. Note that the length of
service life varies depending on the usage condition,
etc.
●Internal battery sometimes swells up as they approach
the end of its service life. This is due to the properties
of lithium-ion batteries, and is not a problem in terms of
safety.
■Charging equipment
●Do not loop the power cord of specied charging
equipment around the adapter main unit. Also, do not
forcibly bend the charging equipment's plug or the
connection between the connector and power cord. Do
not apply excessive force on the cord of the adapter
or the USB cable by placing heavy objects on it or by
pulling it. Doing so may cause malfunction.
●Hold the power plug of the specied charging
equipment when removing from an outlet. Pulling the
cable may damage the cable.
■au IC Card
●Do not forcibly remove or insert au IC Card. Be careful
not to exert excessive force when inserting the card
into your au cell phone.
●You are responsible for any damage caused by inserting
your au IC Card into some other IC card reader/writer,
etc.
●Do not put stickers, etc. on au IC Card.
●Do not insert au IC Card with a conversion adapter
attached to. Doing so may cause malfunction.
●Do not damage au IC Card (use in high temperatures,
dispose of in re, allow foreign objects to contact the
metal portion, subject to shock, bend or place heavy
objects on it, expose to wetting, etc.). Doing so may
cause erasure of data or a fault.
■USB cable
●Do not loop cord of the specied charging equipment
around the adapter main unit. Also, do not forcibly bend
the connection between the plug of the USB cable and
the connector of the adapter. Do not apply excessive
force on the cord of the adapter or the USB cable by
placing heavy objects on it or by pulling it. Doing so
may cause malfunction.
●Hold the plug of the USB cable when removing from the
adapter. Pulling the cable may damage the cable.
■Clear case
●Wipe the clear case that is dirty with a cloth moistened
with cleaning alcohol. Periodical cleaning (once in a half
year) is recommended.
■Earphone microphone
●Do not loop the cord of the earphone microphone
around the product. Do not forcibly bend the plug of
the earphone microphone. Do not place heavy objects
on the cord of the earphone microphone or apply
excessive force such as by pulling. Doing so may cause
malfunction.
●Hold the plug of the earphone microphone when
removing from the headset jack. Pulling by the cord
may damage the cord.
■SIM card removal tool
●Do not insert the SIM card removal tool into a hole
other than the au IC Card/microSD memory card tray.
Doing so may cause malfunction or damage.
●Do not apply excessive force on the tool during use.
Doing so may cause malfunction or damage.
●When disposing the product, dispose it separately
according to your local rule.
●Do not use the SIM card removal tool for other mobile
devices. Doing so may cause malfunction or damage to
the mobile device.
■Camera
●When photographing important occasions, take a trial
shot and check the shot image to make sure it is
correctly shot.
●Do not shoot in areas where shooting is prohibited.
■Copyrights and rights of portrait
●If the data you shot or recorded using the product or
the data you downloaded from the Internet, etc. is in
part or in whole protected by the third party's copyright,
you are not allowed to copy, distribute, publicly send,
modify the data without consent of the copyright
holder, except for personal use, under the copyright law.
In addition, do not use or modify portraits or names
of other individuals without their consent, as it might
infringe on rights of portrait.
Note that shooting and recording may be restricted at
some live performances, shows and exhibitions even for
personal use.
●Be careful about the copyright and portrait right when
posting photos you shot, etc. on Internet homepages.
■Backup content on the product
●Please back up important content registered to the
product or downloaded for the product from an outside
source. Content recorded to memory on the product
sometimes disappears or is altered by unexpected
factors, such as static electricity or a fault, repair,
mishandling, etc.
Notes on Using the Bluetooth®/
Wireless LAN (Wi-Fi®) Function
• Bluetooth® function of the product conforms to
domestic standards of Japan and EC Directive, and has
been certied.
• In some countries/regions, the use of the Bluetooth®
functions may be restricted. If you are using the product
overseas, check the relevant laws and regulations of
the country/region you visit.
• The wireless LAN (Wi-Fi®) function of the product
conforms to domestic standards of Japan and EC
Directive, and has been certied.
• In some countries/regions, the use of the wireless LAN
(Wi-Fi®) functions may be restricted. If you are using
the product overseas, check the relevant laws and
regulations of the country/region you visit.
• Do not use the product in places where electromagnetic
waves are generated or near electric products, AV and
OA equipment, or other magnetized devices.
• Subjecting this product to magnetic or electrical noise
might increase noise and prevent it from performing
communications. (This product is particularly
susceptible to noise when used near a microwave oven.)
• Using this product near a TV, radio or similar appliance
might cause reception interference and disrupt TV
images.
• Searching might not be successful if there are multiple
wireless LAN (Wi-Fi®) access points near the product or
the same channel is being used.
• Since using the product on airplanes is restricted, follow
the instructions given by the respective airlines.
• The communication speed and connectable range vary
depending on the distance between communication
devices, obstacles and the devices used.
Cautions on Using the 2.4 GHz band
The frequencies used by the Bluetooth® and/or Wireless
LAN (Wi-Fi®) function of the product are in the 2.4 GHz
band. In this frequency band, other similar wireless
stations, in-plant wireless stations for mobile unit
identication that require a license for use, such as factory
production lines, specic small power wireless stations
that do not require licenses, amateur wireless stations
(collectively called “other wireless stations” from here on)
are operated in addition to home electrical appliances such
as microwave ovens, devices for industrial, scientic and
medical devices.
1. Before using the product, make sure that "other wireless
stations" are not in operation nearby.
2.
In the event that instances of radio wave interference
have occurred between the product and "other wireless
stations", immediately either relocate the product or
stop operation of the device (stop the emission of radio
waves).
3. If you are unclear on any points or are troubled by
anything, contact an au shop or Customer Service
Center.
◎ Connections between the product and all other
Bluetooth® and wireless LAN (Wi-Fi®) devices have
not been conrmed. Therefore, connections with all
Bluetooth® and Wireless LAN (Wi-Fi®) devices are not
guaranteed.
◎ This product supports security features for wireless
communications that are compliant with the Bluetooth®
and Wireless LAN (Wi-Fi®) standard specications,
but the security may not be su󱐰cient depending on
the usage environment and conguration. Be careful
when making data communication using Bluetooth® or
Wireless LAN function (Wi-Fi®).
◎ Wireless LAN (Wi-Fi®) has the advantage that it
can be freely connected anywhere within the radio
wave range, as it uses radio waves for exchanging
information. At the same time, there is a risk that a
malicious third party may obtain unauthorized access
if security settings have not been congured. At
the customer's discretion and responsibility, it is
recommended that you make security settings before
using the product.
◎ The Company assumes no responsibility for leakage of
data or information that may occur during Bluetooth®/
Wireless LAN (Wi-Fi®) communication.
◎ Since Bluetooth® and wireless LAN (Wi-Fi®) functions
use the same frequency band, using both of the
functions at the same time may cause radio wave
interference resulting in decreased communication
speed or disconnection from the network. If connection
fails, stop using either of the Bluetooth® and Wireless
LAN (Wi-Fi®) functions.
Bluetooth® function/Wireless LAN (Wi-Fi®) function of this
product uses 2.4GHz band.
2.4FH4/XX8/DS4/OF4
• Bluetooth® function: 2.4FH4/XX8
The product uses the 2.4 GHz band. FH4 uses FH-SS
as the modulation scheme. The interference distance is
about 40 m or less.
XX8 uses another modulation scheme. The interference
distance is about 80 m or less.
• Wireless LAN (Wi-Fi®) function: 2.4DS4/OF4
The product uses the 2.4 GHz band. DS-SS and OFDM
are used as the modulation schemes. The interference
distance is about 40 m or less.
• Bandwidth used: all bandwidth
This means that all bandwidths are used, and that bands
of mobile unit identication devices can be avoided.
• Available channels vary depending on countries.
• For use in an airplane, check with the airline company in
advance.
Security Codes/PIN Codes
The product has various security codes that you can use.
Security Codes
The available security codes are as follows. Do not forget
the various security codes that are set as they are
necessary for various operations and contracts.
Be sure to change the initial values to your own codes
before using the product.
● Security code
Example
of usage
① To do remote operation of voice mail and
call forwarding services from a landline
phone
② To use Customer Service Center and
to do various inquiries, applications, and
modications on the au homepage
Initial
value
A four-digit number chosen by the customer
and noted on the application form
● Setting for screen lock
Example
of usage
To set and disable security
Initial value A pattern/PIN/password set by the customer
● Application lock
Example
of usage
To set the application lock when opening an
application
Initial value A four-digit number set by the customer
PIN Code
PIN code
To prevent unauthorized use of au IC Card by a third party,
you can set the product to require PIN code entry every
time the power is turned on. You also need to enter the PIN
code when setting whether PIN code entry is required.
If the PIN code is incorrectly entered three times
consecutively, the PIN code will be locked. You can unlock
the PIN code using the PUK code.
• The PIN code is set to "1234" and PIN code entry is
set not to be required at the time of purchase. You can
change the PIN code to any four- to eight-digit number,
and set PIN code entry to be required as necessary.
• If you require a PIN code to be entered, make sure to
change the number to your own unique number.
PUK code
In case the PIN code is locked, you can unlock it by
entering the PUK code.
• PUK code is an eight-digit number given at the time
of purchase, which is printed on the back side of the
plastic card on which your au IC card is attached.
• After entering the PUK code, you need to set a new PIN
code.
• If the PUK code is incorrectly entered ten times
consecutively, contact an au shop, PiPit or Customer
Service Center.
• The PIN code is not reset by initializing the product.
Notes on Data Communication Charges
• Since constant Internet connection is possible with
the product, data communication may be performed
automatically by some Application.
Therefore, subscription to a flat-rate/discount service
for data communication charges is recommended.
• To browse homepages, download applications,
communicate using applications, send/receive au
mails and congure various settings with the product,
connection to the Internet is required, to which data
communication charge applies.
* Data communication charge does not apply to
wireless LAN (Wi-Fi®) connection.
Notes on Applications
• Be sure to check the security of the application, then
install it at your own risk. Some applications might
cause virus infection, damage various data, and send
out your location information, usage history or personal
information stored in your cell phone via the Internet.
• The Company assumes no responsibility for any trouble
with applications, etc. which the customer has installed.
In this event, the customer may be charged for repairs
even if within the warranty period.
• The Company assumes no responsibility for any
disadvantage brought to you or any third party by
applications you have installed.
• Some applications require that a microSD memory card
be inserted.
• Some applications prohibit the product from entering
the sleep mode while they are active, or rapidly drain the
battery while running in the background.
• Operation procedures and screen appearances of the
applications in the product and those installed by you
are subject to change without notice as a result of
version upgrade. Note that there may be di󱐯erences with
descriptions in this manual.
Setting Application Authority
The rst time you launch an app/function that accesses
the functions or information of the product, a conrmation
screen for requesting access permission appears.
When the conrmation screen appears, conrm the
content and tap "DENY" or "ALLOW".
Example: when activating Photo for the rst time.
a
Home screen→[Google]→[Photos]
b
Conrmation screen for access access
permission→[DENY]/[ALLOW]
Normally, click “ALLOW” to allow the application to
use the function.
Perform the same operation to allow the
application to use other functions.
◎ If the application authority is not allowed, applications/
functions may not be activated or using functions may
be restricted.
◎ To change the authority setting, on the Home screen,
tap [基本フォルダ] (Basic
folder)→[Settings]→[Apps]→application to be
changed→[Permissions]→[ ]/[ ] for the
authority to be changed.
◎ The explanation screen may be displayed depending on
the application/function. Also, the conrmation screen
may be displayed several times or the display may be
di󱐯erent. Carefully check the displayed content, follow
the onscreen instructions.
◎ In this manual, description of the conrmation screens
may be omitted.
Part Material Surface treatment
Fingerprint scanner
ornament
Aluminum
alloy
Positive pole
Fingerprint scanner PC resin Coating
Rear cover antenna
break point
PBT+GF
(40%)
-
Protective lm PET resin -
<HUAWEI Quick Charger>
Part Material Surface treatment
AC adapter main unit PC -
Power plug (Metallic
part)
Cu Ni plated
USB cable TPE -
USB plug/USB Type-C
plug (Metallic portion)
Cu Ni plated
USB plug/USB Type-C
plug (Resin portion)
TPE -
<Clear case (sample)>
Part Material Surface treatment
Main unit PC Inside: high gloss
process
Outside: electrical
discharge
machining
<Earphone microphone (sample)>
Part Material Surface treatment
Earphone portion
(housing), plug (resin
part), remote control
PC -
plug (Metallic part) Cu Ni plated
Mesh SUS -
Cable TPE -
<SIM card removal tool (sample)>
Part Material Surface treatment
Main unit Steel Planer processing
Handling Precautions
Observing the following will prevent product faults and
ensure adequate product performance.
Be sure to read for proper use.
■Precautions common to the main unit, internal
battery, charging equipment, au IC Card, and
peripheral devices
●Do not apply excessive force to the product during use.
Be sure not to put the product into a tightly packed
bag or place a heavy object on the product in a bag.
Sitting on the product in your pocket might damage the
display or internal circuit board resulting in a damage or
malfunction.
Also, doing so with keeping an external device
connected to the external connection terminal or
headset jack may damage the connector resulting in
a malfunction. Such damage and malfunction are not
covered by the warranty, even if there is no external
damage.
●Do not use the product in extremely hot, cold or humid
places.
(Use within an ambient temperature range of 0ºC to
35ºC and humidity range of 5% to 95%.)
●Do not use in places subject to lots of dust or vibration.
Doing so may cause malfunction.
●Clean the external connection terminal and headset
jack with dry cotton swabs, etc. every now and then.
Soiled terminals might cause poor connection. Do not
exert a strong force to clean the external connection
terminals or headset jack to prevent deformation.
●Clean only with a soft and dry cloth (such as the type
used for eyeglasses). Forcefully rubbing with a dry cloth
may scratch the display. The display may be stained if
splash or smear is left attached to the surface. If the
product is wiped with alcohol, paint thinner, benzine,
detergent, or glass cleaner, the printing may be erased
or color may fade.
●Use as far away as possible from land-line phones, TVs
and radios. Using the product near these devices may
a󱐯ect them.
●The product may become warm while charging or during
other operations, depending on the situation, but this is
not abnormal.
●Do not place near corrosive chemicals or in places
where corrosive gas is generated. Doing so may cause
malfunction.
●Do not use outside when you can hear thunder. Doing
so might risk lightning strikes and electric shock.
●Be sure to use only the specied peripheral devices.
Using peripheral devices other than those specied
may cause malfunction.
●Do not put the product in a cooking apparatus such
as microwave oven or a high-pressure vessel. Doing so
may cause malfunction.
●The customer is not allowed to disassemble, modify or
repair the product. Doing so may cause malfunction.
And, modication of the product is in violation of the
Radio Law and Telecommunication Business Act.
●To avoid short-circuiting the connection terminal or
headset jack, do not allow ngers or other part of your
body or conductive foreign objects (metal fragments,
pencil leads, etc.) to come into contact with or get
inside the connection terminal or headset jack. Doing
so may cause malfunction.
●Do not splash liquids such as water. Do not use in
humid places such as a bathroom, and never use the
product with wet hands. Doing so may result in faults
resulting from short-circuiting of electronic circuits or
corrosion.
●Faults caused by wetting with water or humidity are not
covered by the warranty and charges will be incurred for
repair.
●In the event that the product gets wet while charging,
immediately disconnect the power plug of the AC
adapter.
●Do not use the product while driving a car or riding a
motorbike or bicycle or while walking. Use while driving
a car or motorbike is prohibited by law. Use of a cell
phone while riding a bicycle may be punishable by some
regulations.
Do
If there is any chance that the distance
between the product and a person closest
to you may get shorter than 15 cm such as
when you cannot freely move around, set the
product not to emit radio wave in advance (by
setting the Airplane mode, turning the power
o󱐯, etc.).
Somebody nearby may be equipped with electronic
medical equipment such as an implanted
cardiac pacemaker or an implanted cardioverter-
debrillator. Not doing so may cause harmful e󱐯ect
on electronic medical equipment due to radio wave.
Do
Follow the instructions given by the respective
medical facilities regarding the use of the
product on their premises.
Not doing so may cause harmful e󱐯ect on
electronic medical equipment due to radio wave.
Material List
<Main unit>
Part Material Surface treatment
Display Glass -
Exterior case (Front
part)
Glass -
Exterior case (Side and
rear part)
Aluminum
alloy
Sandblast,
positive pole
Polishing
(Graphite black)
au IC Card/microSD
memory card tray
PC+GF
(10%)
-
Power button, volume
button
Aluminum
alloy
Sandblast,
positive pole CNC
processing
Speaker grille SUS PVD coating
Camera lens ornament
(Outside)
Aluminum
alloy
Positive pole
Camera lens Glass Silkscreen print
Flash/Photo light PMMA resin Electrocasting

- 40 -- 39 -- 36 - - 37 - - 38 -
Sold by: KDDI CORPORATION,
OKINAWA CELLULAR TELEPHONE COMPANY
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD.
Imported by: HUAWEI Technologies Japan K.K.
Repair and Delivery Service Center
Business hours: 9:00 to 20:00 (7 days a week)
For loss, theft or damage (toll free)
From fixed-line phones/au cell phones:
0120-925-919
For inquiries, call:
From fixed-line phones:
For general information, charges, and operation assistance (toll free)
0077-7-111
Pressing “zero” will connect you to an operator, after
calling “157” on your au cellphone.
From au cell phones:
157 area code not required
From fixed-line phones:
For service cancelation procedure in case of loss or theft (toll free)
0120-977-033 (except Okinawa)
0120-977-699 (Okinawa)
In case above numbers are not available, call toll-free:
From au cell phones:
113 area code not required0077-7-113
0120-925-314
In case above numbers are not available, call toll-free:
Customer Service Center
Business hours: 24 hours (7 days a week)
Business hours: 9:00 to 20:00 (7 days a week)
濡れた状態での充電は、
異常な発熱・焼損などの原因となり
大変危険です。
Cell phone and PHS operators collect and recycle
unused telephones, batteries and battery chargers
at stores bearing the logo regardless of brand
and manufacturer to protect the environment and
reuse valuable resources.
Rules of Etiquette
Use of the product is not allowed in the
following places!
• Do not listen to music or watch videos while driving a
car or motorbike, or riding a bicycle. Use of cell phones
while driving a car or motorbike is prohibited by law.
(Use of cell phones while riding a bicycle may also be
punishable by law.) In addition, stay alert to the tra󱐰c
around you even when walking. Surrounding sounds may
not be heard clearly, and gazing at the screen might
distract your attention causing a tra󱐰c accident. Be
especially careful at railroad crossings, on a platform,
and at pedestrian crossings.
• Since using the product on airplanes is restricted, follow
the instructions given by the respective airlines.
Consider people around you
• Do not make calls in theaters, museums, libraries,
and other similar places. Turn power o󱐯 or turn on the
manner mode so as not to disturb others around you
with your ringtones.
• In a city area, use in a place where you do not bother
people walking.
• It is extremely dangerous to walk while looking at the
screen of the cell phone. Do not make calls or operate
the product while walking or by stopping suddenly.
• Move to a place where you do not disturb others while
you are in a Shinkansen, a hotel lobby, etc.
• Be careful not to be loud while talking.
• Be careful of sound leakage from earphones in trains or
other places with many people around.
• Ask permission if you take photos with your cell phone
camera.
• When using the camera, follow common rules of
etiquette regarding camera use.
• There may be a person with a cardiac pacemaker nearby
at a place lled with people such as in a crowded train.
Set the "Airplane mode" or turn o󱐯 beforehand.
• When a medical institution has laid down designated
areas where use of the product is prohibited or is not
allowed to be brought in, abide by the instructions of
that medical institution.
Specic Absorption Rate of
Cell Phone, etc.
Specic Absorption Rate (SAR) of Cell Phone
This model [HWV31] cell phone complies with Japanese
technical regulations for exposure to radio waves and
international guidelines on radio wave protection.
This cell phone has been designed in observance of
the Japanese technical regulations regarding exposure
to radio waves *1 and limits to exposure to radio waves
recommended by equivalent international guidelines. These
international guidelines were set out by the International
Commission on Non-Ionizing Radiation Protection (ICNIRP),
which is in collaboration with the World Health Organization
(WHO), and the permissible limits include a substantial
safety margin designed to assure the safety of all persons,
regardless of age and health condition.
The Japanese technical regulations and international
guidelines dene the limits using a unit of measurement
known as the Specic Absorption Rate (SAR), which
represents the average amount of radio frequency energy
absorbed by the human. The SAR limit for cell phones is
2.0 W/kg. The highest SAR value for this cell phone when
tested for use near the head is 1.222W/kg*2. The highest
SAR value for this cell phone when tested for use on the
body is 0.545W/kg*2. There may be slight di󱐯erences in
SAR levels among individual products, but they all satisfy
the limit.
The actual SAR of this cell phone while talking on the
phone can be well below that indicated above. This is due
to automatic changes in the power level of the cell phone
to ensure it only outputs the minimum power required to
communicate with a base station. Therefore in general,
the closer you are to a base station, the lower the power
output of the cell phone is.
This cell phone can be used in positions other than against
your ear. Use an accessory such as a carrying case,
etc. so that you can hold the product at least 1.5 cm
away from your body and also do not contain metal parts
between the product and your body. By doing this, this cell
phone complies with Japanese technical regulations and
international guidelines regarding exposure to radio waves.
The World Health Organization has stated that "a large
number of studies have been performed over the last
two decades to assess whether mobile phones pose a
potential health risk. To date, no adverse health e󱐯ects
have been established as being caused by mobile phone
use."
If you would like to know more detailed information, please
refer to the WHO website.
http://www.who.int/docstore/peh-emf/publications/facts_
press/fact_english.htm
Please refer to the websites listed below if you would like
to know more detailed information regarding SAR.
○ Ministry of Internal A󱐯airs and Communications
website:
http://www.tele.soumu.go.jp/e/sys/ele/index.htm
○ Association of Radio Industries and Businesses
website:
http://www.arib-emf.org/01denpa/denpa02-02.html
(in Japanese only)
○HUAWEI TECHNOLOGIES CO., LTD website:
http://consumer.huawei.com/jp/index.htm
(in Japanese only)
○au homepage:
http://www.au.kddi.com/english/
*1 Technical regulations are dened by the Ministerial
Ordinance Related to Radio Law (Article 14-2 of Radio
Equipment Regulations).
*2 Including other radio systems that can be
simultaneously used.
Export Administration Regulations
This product and its accessories may be under coverage of
the Export Administration Regulations of Japan ("Foreign
Exchange and Foreign Trade Control Laws" and the related
laws and regulations). In addition, Export Administration
Regulations of the United States may be applicable. To
export and re-export the product and its accessories,
take the required measures on your responsibility and at
your expenses. For details on the procedures, contact
the Ministry of Economy, Trade and Industry or the U.S.
Department of Commerce.
Intellectual Property Right
Trademarks
Company names and product names referred to in this
manual are trademarks or registered trademarks of
respective companies.
Google and Google logo, Android and Android logo, Google
Play and Google Play logo, Play Music and Play Music logo,
Play Movies & TV and Play Movies & TV logo, Gmail and
Gmail logo, Google Maps and Google Maps logo, Google Drive
and Google Drive logo, Google Maps Navigation and Google
Maps Navigation logo, Google Chrome and Google Chrome
logo, Google Voice Search and Google Voice Search logo,
YouTube and YouTube logo are trademarks or registered
trademarks of Google, Inc.
Microsoft®, Windows® and Windows® 7/Windows® 8.1/
Windows®
10 are registered trademarks of Microsoft
Corporation in the U.S.A. and other countries.
The official name for Microsoft® Windows® is
Microsoft® Windows® Operating System.
iWnn of OMRON SOFTWARE Co., Ltd. is used for
conversion methods for Japanese language, and for
phrase prediction methods for English.
iWnn IME © OMRON SOFTWARE Co., Ltd. 2008-2017
All Rights Reserved.
QR code is a registered trademark of Denso Wave Inc.
microSD, microSDHC, and microSDXC logo are trademarks
of SD-3C, LLC.
Bluetooth® and its logo are trademarks of Bluetooth SIG,
Inc. HUAWEI TECHNOLOGIES CO., LTD. is licensed to use
this trademark.
WiMAX is a trademark of WiMAX Forum.
Wi-Fi®, WPA®, Wi-Fi CERTIFIED logo, Wi-Fi Protected
Setup logo, Wi-Fi- Direct®, and Miracast® are registered
trademarks of Wi-Fi Alliance.
Wi-Fi CERTIFIED™ and Wi-Fi Protected Setup are
trademarks of Wi-Fi Alliance.
Facebook and Facebook logo are trademarks or registered
trademarks of Facebook, Inc.
Twitter and Twitter logo are trademarks or registered
trademarks of Twitter, Inc.
Instagram is a trademark of Instagram. LLC in the United
States and other countries.
HUAWEI is a trademark or registered trademark of HUAWEI
TECHNOLOGIES CO., LTD.
All other company names and product names are
trademarks or registered trademarks of respective
companies referred to in this manual.
License
Open Source License
This product contains software complying with GNU
General Public License (GPL), GNU Lesser General Public
License (LGPL). The exact terms of GPL, LGPL licenses
are reproduced in "Legal information" in "About phone" in
the product. For details, refer to HUAWEI TECHNOLOGIES
CO., LTD homepage.