Huawei HG530 User manual

HUAWEI HG530 Home Gateway
User Guide

Contents
1 Warnings and Precautions ....................................................... 1
2 Connecting the Cables and Getting Started ........................... 4
2.1 Connecting The Cables .............................................................4
2.2 Getting Started ...........................................................................4
3 Setting the Network-Access Parameters ................................ 6
3.1 Accessing the Network Through the Embedded PPP Dial-Up
Software on the Device....................................................................6
3.2 Accessing the Network Through the PPP Dial-Up Software on
Your Computer .................................................................................7
4 Configuring the Wireless Network Connection...................... 9
5 Configuring the Device........................................................... 11
5.1 Changing the Administrator Password Used for Logging In to
the Web-Based Configuration Utility ..............................................11
5.2 Enabling or Disabling the Wireless Network Function.............12
5.3 Changing the Wireless Network Name and the Access
Password .......................................................................................12
5.4 Changing the IP Address Used for Logging In to the Web-Based
Configuration Utility ........................................................................13
5.5 Restoring Default Settings .......................................................13
6 FAQs......................................................................................... 15
7 Appendix.................................................................................. 22
7.1 Indicators..................................................................................22
7.2 Interfaces and Buttons .............................................................23
7.3 Default Settings........................................................................24
7.4 Technical Specifications ...........................................................24
i

1
1 Warnings and Precautions
To use the device properly and safely, read these warnings and precautions
carefully and strictly observe them during operation. Unless otherwise
specified, the term "device" refers to the device and its accessories.
Basic Requirements
zDuring storage, transportation, and operation of the device, keep it dry and
prevent it from colliding with other objects.
zDo not dismantle the device. In case of any fault, contact an authorized
service center for assistance or repair.
zWithout authorization, no organization or individual can change the
mechanical, safety, or performance design of the device.
zWhen using the device, observe all applicable laws and regulations and
respect the legal rights of other people.
Environmental Requirements for Using the Device
zBefore connecting and disconnecting cables, stop using the device, and
then disconnect it from the power supply. Ensure that your hands are dry
during operation.
zKeep the device far from sources of heat and fire, such as a heater or a
candle.
zKeep the device far from electronic appliances that generate strong
magnetic or electric fields, such as a microwave oven or a refrigerator.
zPlace the device on a stable surface.
zPlace the device in a cool and well-ventilated indoor area. Do not expose
the device to direct sunlight.
zUse the device in an area with a temperature ranging from 0°C to 40°C.
zDo not block the openings on the device with any object. Reserve a
minimum space of 10 cm around the device for heat dissipation.
zDo not place any object (such as a candle or a water container) on the
device. If any foreign object or liquid enters the device, stop using the

2
device immediately, power it off, remove all the cables connected to it, and
then contact an authorized service center.
zDuring thunderstorms, power off the device, and then remove all the cables
connected to it to prevent it from getting damaged due to lightning strikes.
Precautions for Using Wireless Devices
zWhen using the device, ensure that the antenna of the device is at least 20
cm away from all persons.
zDo not use the device where using wireless devices is prohibited or may
cause interference or danger.
zThe radio waves generated by the device may interfere with the operation
of electronic medical devices. If you are using any electrical medical device,
contact its manufacturer for the restrictions on the use of the device.
zDo not take the device into operating rooms, intensive care units (ICUs), or
coronary care units (CCUs).
Areas with Inflammables and Explosives
zDo not use the device where inflammables or explosives are stored, for
example, in a gas station, oil depot, or chemical plant. Otherwise,
explosions or fires may occur. In addition, follow the instructions indicated
in text or symbols.
zDo not store or transport the device in the same box as inflammable liquids,
gases, or explosives.
Accessory Requirements
zUse only the accessories supplied or authorized by the device
manufacturer. Otherwise, the performance of the device may get affected,
the warranty for the device or the laws and regulations related to
telecommunications terminals may become null and void, or an injury may
occur.
zDo not use the power adapter if its cable is damaged. Otherwise, electric
shocks or fires may occur.
zEnsure that the power adapter meets the specifications indicated on the
device nameplate.

3
zEnsure that the power adapter meets the requirements of Clause 2.5 in
IEC60950-1/EN60950-1 and it is tested and approved according to national
or local standards.
Safety of Children
Keep the device and its accessories out of the reach of children. Otherwise,
they may damage the device and its accessories by mistake, or they may
swallow the small components of the device, causing suffocation or other
dangerous situations.
Maintenance
zIf the device is not used for a long time, power it off, and then remove all
the cables connected to it.
zIf any exception occurs, for example, if the device emits any smoke or
unusual sound or smell, stop using the device immediately, power it off,
remove all the cables connected to it, and then contact an authorized
service center.
zDo not trample, pull, or overbend any cable. Otherwise, the cable may get
damaged, causing malfunction of the device.
zBefore cleaning the device, stop using it, power it off, and then remove all
the cables connected to it.
zUse a clean, soft, and dry cloth to clean the device shell. Do not use any
cleaning agent or spray to clean the device shell.
Environmental Protection
zDo not dispose of the device and the accessories in a garbage can.
zDispose of the device according to the local regulations on disposing of
packing materials, exhausted batteries and abandoned devices, and
support the recycling activity.

4
2 Connecting the Cables and Getting
Started
Thank you for purchasing the HUAWEI HG530 Home Gateway (hereinafter
referred to as the HG530).
2.1 Connecting The Cables
If your telephone line is used for both the broadband network access and a
telephone connection, take the following figure as a reference for connecting
the cables.
1. Power adapter 2. Computer
3. Telephone 4. Splitter
5. Telephone jack on the wall a. MODEM interface
b. PHONE interface c. LINE interface
2.2 Getting Started
To power on the HG530, press the power button on the side panel of the
HG530.
After you power on the HG530, the ADSL indicator blinks (for less than three
minutes), which indicates that the HG530 is being activated. After the ADSL

5
indicator stops blinking, the Power and ADSL indicators turn solid on, which
indicates that the HG530 is working properly.

6
3 Setting the Network-Access
Parameters
By configuring the HG530 and your computer, you can choose any of the
following methods to surf the Internet:
zAccessing the Network Through the Embedded PPP Dial-Up Software on
the HG530
zAccessing the Network Through the PPP Dial-Up Software on Your
Computer
3.1 Accessing the Network Through the
Embedded PPP Dial-Up Software on the
Device
If you select this method for accessing the network, the HG530 starts to set up
a dial-up connection automatically after the startup. You can access the
network after you power on your computer. You do not need to install any
special dial-up software on your computer or perform dial-up operations on
your computer. To configure the HG530 and your computer for the network
access, do as follows:
1. Log in to the Web-based configuration utility of the HG530.
1) Launch the Internet Explorer on your computer.
2) Enter 192.168.1.1 in the address bar, and then press Enter.
3) In the displayed dialog box, enter the user name and the password, and
then click OK.
By default, the user name is admin and the password is admin. After the
user name and the password are verified, you can access the Web-based
configuration utility.
2. Enable the embedded dial-up function.
1) In the navigation tree on the left of the Web-based configuration utility,
choose Basic > WAN Setting.

7
2) Select a PVC number, such as 1, from the PVC drop-down combo box.
3) Enter the VPI and VCI that are provided by the network operator in the
VPI and VCI text boxes.
4) Select Yes from the Active drop-down combo box and select Routing
from the Mode drop-down combo box.
5) Select PPPoE from the Encapsulation drop-down combo box.
6) Enter the user name and password that are provided by the network
operator in the Username and Password text boxes, and keep the
default settings of other parameters.
7) Click Submit to save the settings.
After you complete the preceding settings, you can surf the Internet.
You need to perform the preceding operations on a computer once only. The
next time when you power on your computer, you can surf the Internet without
any configuration.
3.2 Accessing the Network Through the PPP
Dial-Up Software on Your Computer
If you select this method for accessing the network, you need to install and
configure the dial-up software on your computer. In addition, you need to
perform dial-up operations on your computer upon each startup. To configure
theHG530 and your computer for the network access, do as follows:
1. Set the working mode of the HG530 to Bridge.
1) Log in to the Web-based configuration utility of the HG530
2) In the navigation tree on the left of the Web-based configuration utility,
choose Basic > WAN Setting.
3) Select a PVC number, such as 1, from the PVC drop-down combo box.
4) Enter the VPI and VCI that are provided by the network operator in the
VPI and VCI text boxes.
5) Select Yes from the Active drop-down combo box and select Bridge
from the Mode drop-down combo box.
6) Click Submit to save the settings.

8
2. Install and configure the PPP dial-up software on your computer.
The PPP dial-up software is pre-installed on certain computer operating
systems. To create a dial-up connection, do as follows (taking the Windows
XP operating system as an example):
1) Choose Start > All Programs > Accessories > Communications >
Network Connections.
2) Click Create a new connection in Network Tasks to display the New
Connection Wizard window, and then click Next.
3) Select Connect to the Internet, and then click Next.
4) Select Set up my connection manually, and then click Next.
5) Select Connect using a broadband connection that requires a user
name and password, and then click Next.
6) Enter the name (as desired) of the dial-up connection in ISP Name, and
then click Next.
7) Select Anyone's use or My use only, and then click Next.
8) Enter the user name and password provided by the network operator
and used for the dial-up connection, and then click Next.
9) Select Add a shortcut to this connection to my desktop, and then
click Finish.
An icon for the dial-up connection is displayed on the desktop of your
computer.
You need to perform the preceding operations only once for creating a network
connection. After the network connection is created, to access the network,
double-click the icon for the dial-up connection, and then click Connect in the
displayed dialog box.