Hubbell KILLARK VSIH Series Owner's manual

HUBBELL ELECTRICAL PRODUCTS
Killark, A Division of Hubbell Inc. (Delaware)
2112 Fenton Logistics Park Blvd.
Fenton, Missouri 63026 USA
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
SERIES VSIH
ATTACHMENT PLUGS
P/N KIL00921520 FORM NO. K1520 R07/21ECO-7-012-21 Page 1of 7
INERIS 20 ATEX 0022X Ex eb IIC T3…T6 Gb
IECEx INE 20.0020X Ex tb IIIC T80oC Db IP66
CML 21UKEX1362X
CAUTION:
Before installing, make sure you are compliant with area classifications, as failure to do so may result in bodily injury, death and property damage. Do
not attempt installation until you are familiar with the following procedures. All installation must comply with the applicable Electrical Code(s).
Make sure that the circuit is de-energized before starting installation or maintenance.
Verify that the installation is grounded. Failure to ground will create electrical shock hazards, which can cause serious injury and or death.
IMPORTANT:
Please read these instructions carefully before installing or maintaining this equipment. Good electrical practices should be followed at all times and this
data should be used as a guide only.
Technical information, advice and recommendations contained in these documents is based upon information that Killark believes to be reliable. All the
information and advice contained in these documents is intended for use only by persons having been trained and possessing the requisite skill and
know-how and to be used by such persons only at their own discretion and risk. The nature of these instructions is informative only and does not cover
all of the details, variations or combinations in which this equipment may be used, its storage, delivery, installation, check out, safe operation and
maintenance. Since conditions of use of the product are outside of the care, custody and control of Killark, the purchaser should determine the
suitability of the product for his intended use, and assumes all risk and liability whatsoever in connection therewith.
16A, 32A, 63A and 125A EXPLOSION-PROOF AND DUST
IGNITION-PROOF ATTACHMENT PLUGS - SERIES VSIH

HUBBELL ELECTRICAL PRODUCTS
Killark, A Division of Hubbell Inc. (Delaware)
2112 Fenton Logistics Park Blvd.
Fenton, Missouri 63026 USA
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
SERIES VSIH
ATTACHMENT PLUGS
P/N KIL00921520 FORM NO. K1520 R07/21ECO-7-012-21 Page 2of 7

HUBBELL ELECTRICAL PRODUCTS
Killark, A Division of Hubbell Inc. (Delaware)
2112 Fenton Logistics Park Blvd.
Fenton, Missouri 63026 USA
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
SERIES VSIH
ATTACHMENT PLUGS
P/N KIL00921520 FORM NO. K1520 R07/21ECO-7-012-21 Page 3of 7
Example Plug Marking Labels - ATEX / IECEx:
THIS DOCUMENT SHOULD BE READ CAREFULLY BEFORE INSTALLATION
1. INSTALLATION , OPERATION AND MAINTENANCE INSTRUCTIONS FOR SAFE USE
1.1 SAFETY RULES
VSIH SERIES sockets (receptacles) are designed as Group II Category 2 equipment suitable for use in fixed
installations in Classifed Hazardous Location areas designated Zone 1/21 and Zone 2/22.
These operating instructions must be kept in a safe place for future reference. Use VHIS Series devices only as
intended and in undamaged / clean condition, and only where the resistance of the material to the surroundings
is assured. NO modifications are allowed to Series VHIS devices which are not specifically described in this
instruction manual. When installing Series VHIS devices, the creepage and clearance distances shall be duly
considered as noted in Item 5.3, Table 8 below.
Series VSIH Plugs are available in materials GRP with the following rated current 16A, 32A, 63A and 125A.
Series VSIH Plugs are intended to be used with Series VSIH Sockets (Receptacles) rated Ex db eb IIC / Ex tb
IIIC. The Series VSIH socket switch handle controls a mechanical interlock mechanism which keeps the plug
from being separated from the socket outlet while the contacts are energized. The plug can only be removed
from the socket (receptacle) when the switch handle is in postion 0 (zero).
1.2 CONFORMITY TO STANDARDS
Series VSIH devices have been evaluated and Certified to the following Standards**:
IEC/EN 60079-0, -7, -31; IEC/EN 60309-1, -2
** - refer to the IECEx and ATEX Certificates for the current editions of each Standard.

HUBBELL ELECTRICAL PRODUCTS
Killark, A Division of Hubbell Inc. (Delaware)
2112 Fenton Logistics Park Blvd.
Fenton, Missouri 63026 USA
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
SERIES VSIH
ATTACHMENT PLUGS
P/N KIL00921520 FORM NO. K1520 R07/21ECO-7-012-21 Page 4of 7
2. TECHNICAL DATA
2.1 TYPES OF PROTECTION
• ATEX / IECEx:
Ex eb IIC T(1) Gb - Ex tb IIIC T80oC Db IP66
Tamb(2) –Tcable: (3)
(1) Temperature Class for Gas according to Table 1.
(2) Ambient temperature range according to Table 1 when different from -20oC to +40oC.
(3) Tcable: “80oC” for Series VSIH20… when max. ambient temperature is +60oC.
Tcable: “85oC” for Series VSIH32… when max. ambient temperature is +60oC.
Tcable: “90oC” for Series VSIH63… when max. ambient temperature is +60oC.
Tcable: “85oC” for Series VSIH125…
2.2 TYPES OF PROTECTION
ATEX Certificate: INERIS 20 ATEX 0022X
IECEx Certificate: IECEx INE 20.0020X
UKCA Certificate: CML 21UKEX1362X
2.3 TABLE 1 –AMBIENT TEMPERATURE RANGE
PLUG SERIES
Ambient Temperature Range
(Tamb)
Temperature Class
(T-Code) - Gas
Max. Surface
Temperature - Dust
VSIH20…
-50oC to +50oC
T6
T80oC
-50oC to +60oC
T5
VSIH32…
-50oC to +60oC
T4
-50oC to +50oC
T4
-50oC to +40oC
T5
-40oC to +60oC
T4
-40oC to +50oC
T4
-40oC to +40oC
T5
VSIH63…
-35oC to +60oC
T3
-35oC to +50oC
T3
-35oC to +40oC
T4
VSIH125…
-35oC to +40oC
T4
The ambient temperature range can be limited by the ambient temperature of the
Series VSIH socket (receptacle). See Killark IOM. K1519 for Series VSIH socket
(receptacle) ambient temperature ratings.

HUBBELL ELECTRICAL PRODUCTS
Killark, A Division of Hubbell Inc. (Delaware)
2112 Fenton Logistics Park Blvd.
Fenton, Missouri 63026 USA
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
SERIES VSIH
ATTACHMENT PLUGS
P/N KIL00921520 FORM NO. K1520 R07/21ECO-7-012-21 Page 5of 7
3. TABLE 2 - PRODUCT NOMENCLATURE : SERIES VSIH SOCKET CATALOG NUMBER SUFFIXES**
POLES
Hz
Volts
Color
h
16A(*)
32A(*)
63A(*)
Color
125A(*)
2P+E
50/60
100-130
Yellow
4
20P304
32P304
---
---
---
50/60
200-250
Blue
6
20P306
32P306
---
---
---
50/60
380-415
Red
9
20P309
32P309
---
---
---
50/60
480-500
Red
7
20P307
32P307
---
---
---
2P+E
300-500
50-500
Red
2
20P302
32P302
---
---
---
3P+E
50/60
100-130
Yellow
4
20P404
32P404
63P404
Black
125P404
50/60
200-250
Blue
9
20P409
32P409
63P409
Black
125P409
50/60
380-415
Red
6
20P406
32P406
63P406
Black
125P406
60
440-460
Red
11
20P411
32P411
63P411
Black
125P411
50/60
480-500
Red
7
20P407
32P407
63P407
Black
125P407
50/60
600-690
Red
5
20P405
32P405
63P405
Black
125P405
50/60
380/440
Red
3
20R403
32R403
63R403
Black
125R403
3P+E
100-300
50-690
Red
10
20P410
32P410
63P410
Black
125P410
3P+E
>300-500
50-690
Red
2
20P402
32P402
63P402
Black
125P402
3P+N+E
50/60
110-130
Yellow
4
20P504
32P504
63P504
Black
125P504
50/60
208-250
Blue
9
20P509
32P509
63P509
Black
125P509
50/60
346-415
Red
6
20P506
32P506
63P506
Black
125P506
50/60
480-500
Red
7
20P507
32P507
63P507
Black
125P507
50/60
600-690
Red
5
20P505
32P505
63P505
Black
125P505
60
440-460
Red
11
20P511
32P511
63P511
Black
125P511
50/60
380-440
Red
3
20P503
32P503
63P503
Black
125P503
3P+N+E
>300-500
380/440
Red
2
20P502
32P502
63P502
Black
125P502
** - Suffixes in Table 2 above may be followed by these optional suffix letters:
ES –Earth Stud (optional)
ESEP –Earth Stud and Earth Plate (optional)
A / AA –Auxiliary contact(s): 1NO + 1NC / 2NO + 2NC
4. TECHNICAL FEATURES
SERIES VSIH ATTACHMENT PLUGS
CATALOG NUMBER
MAXIMUM CURRENT
Tamb 40oC
Tamb 50oC
Tamb 60oC
VSIH 20P…
16A
16A
16A
VSIH 32P…
32A
32A
32A
VSIH 63P…
63A
63A
63A
VSIH 125P…
125A
---
---
WARNING ! The cable entry can reach high temperatures –Suitable cable shall be used.

HUBBELL ELECTRICAL PRODUCTS
Killark, A Division of Hubbell Inc. (Delaware)
2112 Fenton Logistics Park Blvd.
Fenton, Missouri 63026 USA
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
SERIES VSIH
ATTACHMENT PLUGS
P/N KIL00921520 FORM NO. K1520 R07/21ECO-7-012-21 Page 6of 7
4. TECHNICAL FEATURES (Continued)
5. INSTALLATION
5.1 SAFETY INSTRUCTIONS
Use the plug only for its intended purpose. Incorrect / impermissable use, or non-compliance
with these instructions, invalidates the warranty provision. No changes to the plug impairing its
explosion protection are permitted. Install and operate the plug only if it is clean and undamaged.
5.2ACCESSORIES
• Protection Cup
Only approved accessories must be used.
5.3 CREEPAGE AND CLEARANCE DISTANCES
All wiring must be carried out in accordance with the code of practice and installation stanndards
in hazardous areas like IEC/EN 60079-14. Use the correct size of tool and torque (see
manufacturer documents) for tightening the terminal clamps (screwdriver or spanner).
Creapage and clearance distances shall comply with IEC/EN 60079-7 (Table 1). Electrical
parameters shall not exceed the maximum allowed.

HUBBELL ELECTRICAL PRODUCTS
Killark, A Division of Hubbell Inc. (Delaware)
2112 Fenton Logistics Park Blvd.
Fenton, Missouri 63026 USA
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
SERIES VSIH
ATTACHMENT PLUGS
P/N KIL00921520 FORM NO. K1520 R07/21ECO-7-012-21 Page 7of 7
5.4 CREEPAGE AND CLEARANCE DISTANCES
All wiring must be carried out in accordance with the code of practice and installation stanndards in
hazardous areas like IEC/EN 60079-14. Use the correct size of tool and torque (see manufacturer
documents) for tightening the terminal clamps (screwdriver or spanner). Creepage and clearance
distances shall comply with IEC/EN 60079-7 (Table 1). Electrical parameters shall not exceed the
maximum allowed.
Note: Minimum creepage and clearance distances that shall be maintained to conductive parts or other live parts are:
Minimum Creepage
Minumum Clearance
250V
5mm
250V
5mm
400V
8mm
400V
6mm
500V
10mm
500V
8mm
630V
12mm
630V
10mm
Note: Voltages are nominal voltages –the working voltage may exceed by 10% the voltage level given.
6SERVICING AND MAINTENANCE AND REPAIRING
6.1 ROUTINE MAINTENANCE
Routine maintenance is required to guarantee the efficiency of the enclosure and to maintain the
required level of protection.
1) Check that the sealing ring is in place and not damaged…each time the enclosure is opened.
2) Check that all the fixing screws are in place and secured…each time the enclosure is closed.
3) Check that the mounting screws are tight and free of corrosion…annually.
4) Check the body for damage…annually.
5) In Zones where combustible dust is present, it is necessary to periodically clean the upper surface
of the box, limiting the depth of the dust layer to less than 5 mm.
Storage Conditions:
Storage Temperature: from -50oC to +70oC for 16A/32A
Storage Temperature: from -35oC to +70oC for 63A/125A
Relative Humidity: ≤95% RH
The estimated product lifetime is 10 years if storage conditions are respected and all routine care and
maintenance practices specified in this manual are applied.
6.2 RESISTANCE TO CHEMICAL AGENT
Consideration should be given to the environment in which these enclosures are to be used to determine
the suitability of these materials to withstand any corrosive agents that may be present.
6.3 DISPOSAL
Disposal and recycling of the product shall be carried out according to national regulations .