hygena Valencia 656/5790 User manual

MADE IN
BRITAIN
Assembly Instructions - Please keep for future reference
Dimensions
Width - 100cm
Depth - 59cm
Height - 87cm
Valencia - 1000mm Base Cabinet
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 16/08/11
Important - Please read these instructions fully before starting assembly
ALR2653
hygena
hygena
656/5790
633/2882
633/2710
656/5295
656/4540
633/2806
Cabinet
Black Door Pack
Cream Door Pack
Grey Door Pack
Plum Door Pack
White Door Pack

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 26kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2, 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill

Components - Panels
Please check you have all the panels listed below
2
1
80%
x 2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
5
2
6
4
3
Left Side (DPF068A)
(720 x 560mm)
Right Side (DPF069A)
(720 x 560mm)
Loose Shelf (DPF083A)
(968 x 431mm)
Base (DPF082A)
(969 x 494mm)
Back (DPF085A)
(979 x 680mm)
8
Cross Rail (DPF084A)
(969 x 96mm) x 2
Muntin Rail (DPF086A)
(36 x 688mm)
7Valencia Door (DPF147B)
(497 x 716mm) x 2
The front surface
of this door is
protected with a
peel-off film

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
see malibu fitment mk2 for large number of panels and fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 12
B
Metal dowel (F901) x 8
C
D
Large locking
nut (F900) x 8
F
G H I a
I c
I d
I e
I b
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
13mm Screw (F63) x 8
E
13mm Screw (F79) x 6
Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2
L M
25mm Screw (F50) x 6
N
Hinge Cover (F119) x 4
Bracket (F945) x 4
Shelf support (F110) x 6
Hinge Plate
(F117) x 4 Hinge Arm (F118) x 4
Leg Bracket
(F127) x 3
Leg Socket
(F120) x 5
Leg Clip
(F128) x 3
16mm Screw
(F129) x 21
Leg (F122) x 5
hygena
O
40mm Screw (F910) x 2
P
P
a
b
25mm Screw (F132) x 4
Handle (F214) x 2

Assembly Instructions If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
80% x 2
B
B
B
L
L
J
J
J
E
1
L
J
E
5mm
150mm
Only screw ONE metal dowel into
one of these holes.
1st 5mm hole
2nd 5mm hole
B
B
1
Prepare the left side
Fit 2 hinge plates onto
the left side ,
orientated as shown.
Screw 3 metal dowels
into the holes shown on
the left side .
Fit a bracket flush to
the top edge of the left
side , about 150mm
in from the groove, see
diagram.
Secure the bracket
using screw .
Fit another bracket
flush to the back edge of
the left side , about
5mm down from the top
edge, see diagram.
Secure the bracket
using screw .
Note: The brackets must
be flush with the
top/back edge of the
panel.
B
1
J
J
1
J
1
E
J
E
Step 2
Prepare the left side
Screw a metal dowel
into one of the holes
shown on the left side
. .
Note: Tighten metal
dowels up fully against
the panels.
B
1
B
4
L
Prepare the right side
Fit 2 hinge plates onto
the right side , making
sure that the slot is
facing towards the front
edge.
1
If you ARE fitting a sink unit
we recommend that you
use the 2nd 5mm hole.
If you ARE NOT fitting a sink
unit we recommend that
you use the 1st 5mm hole.

Assembly Instructions
5
Step 3
Prepare the right side
Screw a metal dowel
into one of the holes
shown on the right side
. .
Use the same hole that
you used for the left side
in step 1.
L
Prepare the right side
Fit 2 hinge plates onto
the right side ,
orientated as shown.
Screw 3 metal dowels
into the holes shown on
the right side .
Fit a bracket flush to
the top edge of the right
side , about 150mm
in from the groove, see
diagram.
Secure the bracket
using screw .
Fit another bracket
flush to the back edge of
the right side , about
5mm down from the top
edge, see diagram.
Secure the bracket
using screw .
2
B
2
J
J
2
J
2
E
J
E
Step 4
J
E
J
E
L
L
L
B
B
B
J
J
2
Only screw ONE metal dowel
into one of these holes (use
the same hole that you used
for the left side in step 1).
B
B
2
2

Assembly Instructions
6
Step 5
Step 6
I a I a
I b
b:
a:
c: d:
Fit the legs to the
base
a: Push the leg sockets
. into the holes in the
base as shown.
b: Secure each leg
socket with 3
screws .
c: Tap in the centre plug
on each leg socket .
d: Push the leg into
the leg socket .
I a
I a
I a
I e
I e
3
x 3
I a
I a
I b
I a
I a
I a
I a
3
A
A
Step 4
Prepare the base
Insert 4 large locking
nuts into the base
as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 6 wooden dowels
into the base as
shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
C310mm
A
A
3
A
A
A
C
C
C
C
A
3
A
A
A
A
A
C
C
A
C
C
I a

A
Assembly Instructions
7
Step 7
Step 8
Finished
front edge
Step 6
Step 7
C
Prepare the 2 cross
rails
Insert 2 large locking
nuts into the cross
rails as shown.
Tap 2 wooden dowels
into the cross rails as
shown.
Step 9
4
4
A
Join the right side and
base
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
F
3
3
2
C
C
2
3
2
A
4
Fit a cross rail
Push a cross rail
onto the right side as
shown.
Use a screwdriver to
tighten the large locking
nut fitted to the cross
rail .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
C
C
4
C
C
4
4

O
Assembly Instructions
8
Step 10
Step 11
Prepare the muntin
rail
Tap 2 wooden dowels
into the muntin rail as
shown.
3
4
A
A
A
8
8
Fit the muntin rail
Attach the muntin rail
to the base and
cross rail and secure
with 2 screws .
O
8
8
3
4
O
Step 12
3
4
Support this cross rail
until the left side has been
fitted in the next step.
4
Fit a cross rail
Push a cross rail
onto the right side as
shown.
Use a screwdriver to
tighten the large locking
nut fitted to the cross
rail .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
C
C
4
2
If you are fitting a sink
unit you will need to fit
this support rail here
(refer back to step 3).

Assembly Instructions
9
Step 13
M
Step 14
2
3
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the large locking
nut fitted to the 2
cross rails and the 2
fitted to the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
1
C
C
4
4
4
1
2
1
Fit the back
Slide the back along
the grooves in the side
panels and .
6
6
1 2