hygena 296/7378 User manual

Issue 1 - 10/10/14
296/7378

Shelf Support
Hex Key x 1
Panel Stieners Wall Plug

1
3
4
2
3
4
using Hex key supplied
to tighten

5
1.Slide back panel 5 along
grooves in panels and
1.Glue holes in top panel
and connect to left side panel
and right side panel
2.Insert 2 x female camlocks
to attach top panel
to left side panel and
right side panel
3 4
5
1
34
1
3
4
Use a screwdriver to turn the
female camlock clockwise to
lock.
“Using Camlocks”
section at the front of this
instruction for further
assistance.
Please refer to the
3. Cover visible camlocks
with 2 x Stickers as
shown
4

Attach Hinge
Warning: Styrofoam or a
towel should be placed
beneath the mirror when
doing this to provent
scratches
6
2 x
6
7

supports
supports
3
4
7
5
panel stifferners
8
9

WALL
1. Lift the unit into position
ensuring that the fixing clips
attached to the unit are firmly
hooked over the screw
heads.check the unit
periodically to see that no
fitting has loosened and
needs attention
1.Use the template
provided to mark on the wall
the position of the fixings.
Please use a spirit level to
ensure your markings are level
3. Insert 4 x wall plugs into
each. Insert the 4 xscrews
provided and tighten. leaving
the screw head exposed by
about 1/4 inch (6mm).
2. Drill holes with a drill and a
suitable drill bit.
Assembly Complete
10
11

A Guide to Wall Mounting & Fixings
lmportant note:
lf plastic wall plugs(rawl plugs)
are supplied with your product,
e.g.:
- these are only suitable for use in
masonry walls.
lf you are in any doubt about the
correct wall plugs for your wall,
seek professional advice.
Failure of the product due to
using the incorrect fixings is the
responsibility of the installer.
lmportant: when drilling into walls always check
that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used are suitable for
supporting your unit.Consult a qualified tradesperson if you
are unsure.
Hints:
General rule: always use a larger screw and wall plug if you are
not sure.
Ensure you use the recommended drill bit to match the wall plug and
hole size.
Ensure you drill the hole horizontally; do not force the drill or enlarge
the hole.
Take extra care when drilling high walls,ceilings and ceramic tiles.
Ensure wall plugs are inserted beyond the thickness of the ceramic
tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the folllowing types of wall plug if your walls are made
of brick, breeze block, concrete,stone or wood.
No.1"General Purpose" wall plug No.3"Cavity Fixing" wall plug No.5"Hammer Fixing" wall plug
Generally aerated blocks should not
be used to support heavy loads,use
a specialist fitting in this case. For
light loads, general purpose
wall plugs can be used.
For use with plasterboard partitions
or hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing
allows it to be fixed to the wall
rather than the plasterboard.
Always check the fixing is secure
to the retaining wall.
No.2" Plasterboard"
wall plug
No.4" Cavity Fixing - Heavy Duty"
wall plug
No.4" Shield Anchor" wall plug -
heavy loads
For use when attaching light loads
onto plasterboard partitions.
or use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as
TV and HiFi speakers and satelite
dishes etc.
lf you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800