hygena 249/8940 User manual

Width - 45cm
Depth - 53cm
Height - 83cm
Important – Please read these instructions fully before starting assembly
Customer Helpline: 0345 640 0800
Dimensions
Issue 1 - 10/03/14
Hygena Chair
If you need help or have damaged or missing parts, call the
7
c:
d:
c:
After the sitting test,
re - tighten bolts again,
if any adjustment needed.
d:
It is highly recommend
to re - tighten all the bolts
again after using the chair
for 7 days.
Note : Please keep the
allen key to re - tighten
all bolts again when
required.
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 640 0800
Assembly is complete.
Assembly Instructions - Please keep for futrue reference.
249/8940

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
page 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• Maximum safe weight of
user: 110 Kgs.
Step 2
e:
Assembly Instructions
Attach lock bracket
by using screw as
shown in the figure.
E
De:
a:
Tighten all bolts.
Note : Place the chair on
a level floor.
a: b:
b:
Sit on the chair.
6
Note : This step is
D
Pre-drilled
hole
E
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts.
• Reguraly check and ensure
that all bolts and fittings are
tightend properly.
essential to prevent the
chair from wobbling due to
legs uneven.
• Do not stand on the chair.
• Do not use the chair as step
ladder
• Assemble the item as close
to its final position (in the same
room) as possible.

2
Components - Parts
Please check you have all the parts listed below
Chair back x 1 Seat x 1
If you have damaged or missing components,
call the
Customer Helpline: 0345 640 0800
12
Front leg frame x 1
3
4Side rail x 2 (L,R)
Right side rail
Left side rail
5
c:
Assembly Instructions
d:
d:
c:
Place the chair on the
floor. Insert bolts with
spring washers and
washers through side
rails holes into front leg
frame screw all bolts
by using allenkey .
3
A
F
B
C
Place the seat pad
on the table. Put the
chair frame on top of the
seat back.
2
A
B
C
2
3
BACK
1
4
4
BACK BACK
Note :The quantities below are the correct amount to complete the assembly of 1 chair.

Assembly Instructions
Step 1
a: 4A
Components - Fittings
Please check you have all the fittings listed below
Note :The quantities below are the correct amount to complete the assembly of 1 chair. In some cases more
fittings may be supplied than are required.
Bolt x 8
B
Spring washer x 8
C
D
Washer x 8
F
Lock bracket x 2 Allenkey x 1
A
E
Screw x 4
b:
Attach left and right
side rails onto the chair
back with bolt ,
spring washers and
washers by using
allenkey as shown in
the figure.
B
C
F
Do not fully tighten.
Fit the front leg frame
onto the side rails .
34
3
1
a:
b:
4
pre - drilled hole
Right side rail
Left side rail
A
B
C
4
BACK
4
4
1
Tools required
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
4
4
3