hygena Bergen 557/2911 User manual

Dimensions
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Height - 101.5cm
Depth - 38.1cm
Width - 45.6cm
Bergen 5 drawer chest
Argos = 03456 400 800
557/2911
575/9576
549/4006
571/3079
576/9470
576/9470 WHITE/MIRROR
571/3079 WHITE HG
549/4006 WHITE
575/9576 WALNUT
557/2911 OAK
Issue: 3 - 19/12/16
DR82517

1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
•
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below•
Important – Please read these instructions fully before starting assembly
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
Safety and Care Advice

Please check you have all the panels listed below
Components - Panels If you have damaged or missing components,
call the Customer Helpline:
2
03456 400 800
Drawer base x4
(386x299x2,5)
BO2512
Drawer base x1
(386x299x2,5)
BO251260
2Back Broad
(974x435x2,5)
BO3443
8Drawer back x5
(374x120x12,50)
LA1629
@Drawer left side x5
(305x120x12,50)
LA1631
!Drawer right side x5
(305x120x12,50)
LA1632
6Top
(456x381x15)
P1985
4Bottom
(455x381x15)
P1986
5Foot
(410x340x22)
P1987
3Right side
(963x380x15)
P2191
1Left side
(963x380x15)
P2192
7Drawer front x5
(419x188x15)
P4233
0Plinth
(424x92x15)
P7099
9a
9b

Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Tools required
Eye protection
(when using a
hammer or glue)
Ruler/tape
measure
0102030405060708090 100 110 120 130 140 150
0123456
Small
hammer
Setsquare
Spirit level
Drill
6mm Suitable drill bit
(for use with wall plug)
Flatblade screwdriver
(medium)
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length ismeasured from thehead to the point (30mm screw shown).
3
Parkerscrew x 1
ZF99936B
O
Wall plug x 1
ZF99936A
N
Handle x 5
GR1978
M
felt x 6
FK1416
L
Glue x 1
FA1510
K
Drawerbase support x 32
FK1250
J
L-Bracket x 1
FK1235
I
Wood dowel x 2
FK1410
H
(5x30mm)
15mm
Large locking nut x 10
FK1012
G
(15x12mm)
12mm
Small locking nut x 10
FK1010
F
(12x10mm)
Locking screw x 20
FK1011
E
(5x24mm)
Euro Screw x 20
FK1301
D
(6.3x10mm)
Pozi Screw x 85
FK1309
C
(4x12.5mm)Screw x 1
FK1400
B
(4x15mm)Screw x 4
FK1322
A
(4x30mm)
Q
Runner left part A x 5
PPM1516LA
Runner left part B x 5
PM1516LB
S
Runner right part A x 5
RPM1516RA
Runner right part B x 5
PM1516RB

Assembly Instructions
4
Step 1
a: Prepare the drawer
fronts
Screw 2 locking screw E
into the holes shown on the
back of each drawer
front 7.
Note: Insert locking
screw Eas far as shown.
Do not over tighten.
b: Prepare the drawer
sides
Insert a small locking nut F
into the hole on left drawer
side @and right
drawerside !.
Make sure the ‘arrow’ on F
is pointing towards the hole
in the edge of @and !.
Put drop of glue Kin the 6
holes of drawersides @and
!before sliding them onto
the dowels of
drawerback 8.
Slide drawerbase 9in the
grooves of the drawer-unit.
c: Turn the drawer wrap
assembly over and push onto
the drawer front 7. Use a
phillips or flatblade
screwdriver, that is a good fit,
to turn 24mm locking nut F
as far as it will go - more than
1/2 turn.
7
!
8
@
7
a:
b:
5x
5x
5x
c:
E
E
F
F
K
F
If Highgloss,
Please remove
the protective film!
9a/b

J
J
JJ
Assembly Instructions
5
5x
d:
3
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
D
D
R
R
R
R
R
C
CC
C
C
C
C
Step 1 continued
finishing the drawers
d: Turn over drawer and
slide drawerbase
supports Jin corner as
shown and fix them, using
the attached screws .
b: Insert 4 Large locking
nuts Ginto right side 3
where shown. Make sure
the ‘arrow’ on Gis pointing
towards the hole in the
edge of 3.
Screw 1 locking screw E
into the hole shown of the
right side 3.
Note: Insert locking
screw Eas far as shown.
Do not over tighten.
a:
b:
Finished
front edge
Finished
front edge
E
3
G
G
G
G
C
C
C
D
D
R
Attaching runners
Step 2
a: Fix runner right part A R
on right side 3as shown
using euro screw drawer
Dand pozi screw C.

a:
b:
Assembly Instructions
Attaching runners
Step 3
C
C
C
D
D
P
b: Insert 4 Large locking
nuts Ginto left side 1
where shown. Make sure
the ‘arrow’ on Gis pointing
towards the hole in the
edge of 1.
Screw 1 locking screw E
into the hole shown of the
left side 1.
Note: Insert locking
screw Eas far as shown.
Do not over tighten.
a: Fix runner left part A P
on left side 1as shown
using euro screw drawer
Dand pozi screw C.
Put drop of glue Kinto the
2 holes of plinth 0.
Put dowels Hinto the
holes of plinth 0.
6
Finished
front edge
Finished
front edge
1
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
P
P
P
P
P
D
D
D
G
G
G
G
1E
Step 4
Insert 2 Large locking
nuts Ginto plinth 0
where shown. Make sure
the ‘arrow’ on Gis pointing
towards the hole in the
edge of 0.
H
H
10
G
G

5
4
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
Step 6
Position bottom 4onto
foot 5and fix with 30mm
chipboard screw A.
Screw 24mm locking
screws Einto bottom 4.
Note: Insert
locking screw Eas far as
shown.
Do not over tighten.
7
3
10
G
G
E
E
E
E
A
A
A
A
1
Step - 5
b: Attaching top
Position plinth 0onto
right side 1.
Use a screwdriver to turn
locking nuts Gclockwise
to lock.
Position right side 3onto
plinth 0.
Use a screwdriver to turn
locking nuts Gclockwise
to lock.

a:
b:
Finished
front edge
Assembly Instructions
8
5
4
5
L
L
L
L
Step - 7
A: Attaching bottom
Position bottom 3onto
left & right side 1, 3.
Use a screwdriver to turn
locking nuts Gclockwise
to lock.
A: Attaching felt
Stick the selfadhesive
felt Lstrategically
underneath the foot 5.

Finished
front edge
Assembly Instructions
Insert back board
Turn chest upright and slide
back board 5in the groove.
Step 9
a: Prepare top
Screw 4 locking screw E
into the holes shown on top
6.
Note: Insert
locking screw Eas far as
shown.
Do not over tighten.
9
E
E
E
E
2
6
Step - 8