Hytronik HC401SRC/R User manual

INSTRUCTION MANUAL FOR MICROWAVE MOTION SENSOR
Model No.:HC401SRC/R
Technical Specifications
PRODUCT TYPE: Microwave Motion Sensor
OPERATING VOLTAGE: 120-277VAC 50Hz/60Hz
HF SYSTEM: 5.8GHz CW radar
RATEDLOAD: 400W@120VAC
800W@240VAC
1000W@277VAC
DETECTIONANGLE: 30 ~150
POWER CONSUMPTION: <0.5W
DETECTIONRANGE: Max.16 meters in diameter, adjustable
TIME SETTING: 5s~30min.
DAYLIGHT SENSOR: 2~50Lux; disable
MOUNTING: Indoors, ceiling & wall mounted
INSTALLATION HEIGHT: ≤15M
WORKINGTEMP.: -20 ~ +60℃
HC401SRC/R HRC-03
The sensor is an active motion detector; it emits a high-frequency electro-magnetic wave 5.8GHz and receives its echo. The sensor detects the change
in echo from movement in its detection zone. A microprocessor then triggers the switch light ON command. Detection is possible through doors, panels
of glasses thin walls.
Note: the high-frequency output of this sensor is <0.2mW; approximately just 0.2‰of the transmission power of a mobile telephone or the output of a
microwave oven.
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION AND RETAIN THIS LEAFLET IN A KNOWN
AND SAFE PLACE FOR FUTURE REFERENCE.
SECTION 1 INSTALLATION AND WIRING
1.1 Ensure that the electricity supply is switched off before installing or servicing this product.
1.2 Wiring diagram
°°
(capacitive load)
LN N
Antenna module
Installation hole
Daylight sensor
Detection area
IR receiver
Daylight sensor
Buzzer
Hold-time
L’ ON/
OFFAuto ModeRESET
SC1 SC2 SC3
100%
30S
10min
0S
10%
75%
1min
10S
20%
50%
5min
1min
1H
30%
10%
5min
50%
SC4
Hold-time
Stand-by period
Daylight Sensor
Scene mode
Detection range
Stand-by dimming level
Control Gear
L’ N N L
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel:[phone] F:86-752-2777877
E: [email protected] W:www.hytronik.com
CHINA FACTORY
Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,
Kowloon Bay, Kowloon, Hongkong
T: 00852-35197525 F: 00852-30116936
E: [email protected]
HYTRONIK INDUSTRIAL LIMITED

SECTION 2 REMOTE CONTROL
HRC-03
Permanent ON/OFF [ ]
1. Press button , the light goes to permanent ON or permanent OFF mode.
2. Press button to quit from this mode.
(
Please refe
r
to explanation accordingly)
Auto Mode [ ]
Press button goes to auto mode, the sensor starts working and all settings remain the same as the latest status before the light was switched ON/OFF.
Note: the buzzer beeps one time when RC
receives signal successfully
RESET [ ]
Press button , all settings go back to the value of DIP settings.
Test 2s function [ ]
1. Press button , the sensor goes to test mode(hold time 2s), stand-by period and daylight sensor are disabled.
2. Press button to quit from this mode, and the sensor setting is changed accordingly.
Ambient daylight threshold [ ]
Press button , the latest surrounding lux value overwrites previous lux value learned, and is set as the daylight threshold. This feature enables the
fixture to function well in any real application circumstance.
Detection range[ ]
Press buttons in zoneto set detection range at 100% / 75% / 50% / 10%.
Hold time [ ]
Press buttons in zoneto set hold time at 30s / 1min / 5min / 10min / 30min.
Daylight sensor setting [ ]
Press buttons in zone to set daylight sensor at 2lux / 10lux / 30lux / 50lux.
Note: buttons are disabled.
1
2
3
234
button 1
button 2
button 3
6
3
9
5
7
8
11 12
4 7
button 6
button 9
Daylight sensor disable [ ]
Press button , the built-in daylight sensor stop working, and all motion detected could turn on the lighting fixture, no matter how bright the
natural light is.
10
button
10
zone 5
zone 7
zone 8
Scene mode options [ ]
Note:end-user can adjust the settings by pressing buttons of detection range / hold time /
stand-by period / stand-by dimming level /daylight sensor , the last setting stays in validity.
57
8
11
12
zone 4
There are 4 scene modes built-in the remote control for different applications:
Scene options Detection range Hold time Daylight sensor
SC1 100% 1min 2Lux
SC2 50% 5min 10Lux
SC3 100% 10min 10Lux
SC4 100% 30min 50Lux
ON/
OFFAuto ModeRESET
SC1 SC2 SC3
100%
30S
10min
0S
10%
75%
1min
10S
20%
50%
5min
1min
1H
30%
10%
5min
50%
SC4
Hold-time
Stand-by period
Daylight Sensor
Scene mode
Detection range
Stand-by dimming level
3
1
2
5
8
9
4
7
6
10
11
12

SECTION 5 TROUBLE SHOOTING
SECTION 4 FUNCTIONS
SECTION 3 SETTING
YDEMERESUACYDEMERESUACNOITCNUFLAM
The load does not work
gnittestsujdAdetcelesgnitteslortnoc-thgiltcerrocnI
daolecalpeRytluafdaoL
NOhctiwSFFOhctiwssniaM
gnittesenozkcehCenoznoitcetedehtnitnemevomsuounitnoCnosyawlasidaolehT
The load is on without any identifiable
movement
The sensor is not mounted for reliably detecting movement Securely mountenclosure
Movement occurred, but not identified by the sensor
(movement behind wall, movement of small object in
immediate lamp vicinity etc.)
Check zone setting
The load does not work despite movement Rapid movements are being suppressed to minimize
malfunctioning or the detection radius is too small Check zone setting
4.1 Zero-cross Relay Operation
Designed in the software, sensor switches on/off the load right at the zero-cross point, to ensure the in-rush current is minimised, enabling the
maximum lifetime of the relay.
I - 100%
II – 75%
III – 50%
IV – 25%
V – 10%
I – 5s
II – 30s
III - 1min
IV – 5min
V – 10min
VI – 30min
I – Disabled
II – 50 Lux
III – 30 Lux
IV – 10 Lux
V – 2 Lux
Detection area can be reduced by selecting the combination on the DIP switches to fit precisely for each specific application.
Detection area
Hold-time means the time period to keep the lamp on 100%, after all motion has ceased (detection area vacated).
Hold-time
The daylight threshold can be set on DIP switches, to fit for particular application.
Daylight sensor
100%
75%
50%
25%
10%
5s
30s
1min
5min
10min
30min
1 2 3
Disable
50 Lux
30 Lux
10 Lux
2 Lux
1 2 3