Hytronik HMW32 User manual

Daylight Harvest with Remote Control
IP65 High Bay HF Motion Sensor
IP65RED
Stand-by power
EMC standard (EMC)
Safety standard (LVD)
Radio Equipment (RED)
Resistive
EN55015, EN61000
Semko, CB, CE , EMC, RED, RCM
EN60669-1, EN60669-2-1
Model No.HMW32
120 ~277VAC 50/60Hz
Mains voltage
Load ratings:
EN300440, EN301489-1,
EN62479
<1W
Input Characteristics
Safety and EMC
400VA@120V; 800VA@220 -277V
800W@120V; 1600W@220 -277V
Capacitive
Sensor Data
HMW32
Operation temperature Ta: -20
O
C ~ +70
O
C
Environment
IP65
IP rating
Model No.
<0.2mW
5.8GHz +/- 75MHz
High Frequency (microwave)Sensor principle
Operation frequency
Transmission power
Detection range
Detection angle
Max. ( Ox H) 10m x 15m
20sWarming-up
Technical Data
360 O
Mechanical Structures and Installations
For more details, please refer to user manual.
HF
A. Ceiling mount
Sensor module
Photocell
LED indicator
Infrared receiver
Rotary switch Cable entry
Installation rack
91.5
59.3 57.3
47.5
4.1
80.7
75
4.1
66.6
81.5
Inf
ra

Intelligent Photocell (daylight detection prior to motion detection)
1
The built-in photocell will also automatically turn o the light when the ambient natural light exceeds the programmed lux level for
stays at
dimmed level during absence.
switches on the light automatically when
presence is detected.
does not switch on when presence is
detected.
The sensor switches o the light when
presence.
Functions and Features
C. Attach to the shade by clamp
B. Screw to the Luminaire by conduit
Photocell
Sensor module
Photocell
LED indicator
Infrared receiver
Rotary switch
Angle adjustment
Luminaire clamp
Sensor module
LED indicator
Infrared receiver
Rotary switch
Cable entry
59.6
66.6
89.9
0.825”
75 64
59.3 57.3
35.2
47.5
75
64
84.5
59.3
47.5
53
66.6 80
146.6
18
50
g
ht, the li
g
es notswitchonwhen presence
g
ht, the
s
itches on thelight automatically
T
he sensor switches o the li
gh

Daylight Harvest
Light will not switch on
when natural light is
motion detected.
The light switches on
automatically with
presence when natural
The light turns on at full or dims to maintain the lux level. The light output
regulates accroding to the level of natural light available.
The light dims to stand-by
period after hold-time and
stays on selected minimum
dimming level.
The light switches o when
the ambient natural light is
The light switches o
completely after the
stand-by period.
2
Note:
The Light automatically dims down and
eventually turns o if the natural light lux
level exceeds the daylight threshold.
However, if the stand-by period is preset
but dim to minimum level, even the
zero-cross point
Alternating current
Zero-cross Relay Operation
Designed in the software, sensor switches on/o the
load right at the zero-cross point, to ensure that the
in-rush current is minimised, enabling the maximum
lifetime of the relay.
3
A rotary switch is built inside the sensor for scene
selection / fast programming. Total 16 channels
are available:
Rotary switch preset
Rotary Switch Preset
Note: settings can also be changed by remote control
HRC-11.The last action controls.
0 5s100% Disable
nim11 100% 50Lux
nim52 100% 50Lux
nim53 100% 75Lux
nim54 100% 100Lux
nim55 100% 200Lux
nim016 100% 50Lux
nim017 100% 75Lux
nim018 100% 100Lux
nim019 100% 200Lux
nim02A 100% 100Lux
nim02B 100% 200Lux
C 30min100% 100Lux
nim03D 100% 200Lux
E30min100% 400Lux
F5s100%
10%
10%
10%
10%
10%
30%
10%
10%
10%
30%
10%
30%
10%
30%
50%
10%100Lux
10s
5min
10min
+∞
+∞
+∞
30min
+∞
+∞
+∞
1h
+∞
+∞
+∞
+∞
10s
Detection
range
Channel Hold-time Stand-by
time
Stand-by
dim level
Daylight
sensor

1. Press button “Shift”, the red LED is on for indication.
2. Press button “Sensor o”, the function of movement detection is disabled.
Settings (Remote Control HRC-11)
HRC-11
Press button “RESET”, all settings go back to rotary switch settings.
Reset Settings
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
ON/
OFF
Sensor o (Daylight harvest without occupancy)
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Twilight” function is disabled.
Power output
Load Indication:
receiving the commamd from the
remote control successfully.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
Note: “Semi-auto” function is disabled.
Press the buttons to adjust the light brightness to reset the target lux level.
Brightness +/-
Scene program - 1-key commissioning
Detection range
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to setall
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button“Start”, button ”100%”, “Disable”, “Shift”,“5min”, “Shift”, “+∞”, “30%”,“Memory”. By pointing tothe sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
&
A
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button

Press buttons in zone“ Daylight threshold” to set daylight sensor / target lux level at 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: 2lux / 10lux are disabled.
Daylight threshold
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold / target lux level.
Ambient daylight threshold
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Dual tech & RF mode
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
at thestand-by dimming level
whenno presence after motion hold-time.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
All buttons are disabled.
Wiring Diagram
Detection Pattern
Ceiling mounted height(m)
10%
30%
75%
50%
HMW32
Brown
LED driver
L
N
1-10V+
1-10V
L
N
Blue
Grey
Red
Black
-
2. Select a time period and the sensor will do light level measurement and determine/save the lowest light level (commission line)
with 100% light on, so as to set the target lux level automatically.
Note: 1. Make sure the light level measurement covers the night time.