Hytronik DS05 User manual

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 1/4
DS05 DS06 DS07
Photocell AdvanceTM Version with Remote Control
Daylight Sensor
Applications
Thanks to the Photocell AdvanceTM function, these daylight sensor can built
inside the xture completely. The xture is effectively controlled by the
daylight sensor, automatic on/off operation based upon daylight.
No drill or hole is needed for accessing the daylight condition
Works from behind the xture cover/diffuser
Use for retrot and new building installations
Daylight sensor
Daylight threshold
Antenna module
Infrared receiver
Installation hole
L’ N N L
DIP switch setting (Daylight Threshold)
Set the lux level according to the real application environment. Light
keeps off if ambient daylight is sufcient (above the threshold preset).
With insufcient natural light, light will automatically turn on.
Light will never switch off when daylight threshold is set to disable.
123 4 5 6
2 Lux
10 Lux
30 Lux
123456
100 Lux
300 Lux
500 Lux
50 Lux
1
DS05 (On/off control)
Stand-by power
800W
80mA
Model No. DS05 DS06 DS07
220~240VAC 50Hz
Mains voltage
Switched power:
Switched power
<1W
400VA
20s
Warming-up
Technical Data
Tc: +80
O
C
Operation temperature
Case temperature (Max.)
Ta: -20
O
C~ +60
O
C
IP20
IP rating
Model No.
2 ~ 500 lux, disabledDaylight threshold
DS05 DS06 DS07
Capacitive
Resistive

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 2/4
2
DS06 (Daylight harvest function, 1-10V output)
3
DS07 (Daylight harvest function, DALI output)
120
30
21
4.5
110.5
4.5
Functions and Features
Photocell AdvanceTM Function
1
It’s well known that LED lights have a totally different spectrum to natural light. Hytronik uses this principle and comes up with special
photocell and sophisticated software algorithm to measure and differentiate natural light from LED light from behind the xture cover,
so that this photocell can ignore internal LED light and only respond to the natural light outside.
Our technology has no infringement to the existing patents in the market.
The light turns on at full or dims to maintain the lux level. The light output
regulates according to the level of natural light available.
The light dims to minimum
level then switches off
when natural light is
sufcient.
The light automatically
switches on when natural
light is insufcient.
Daylight Harvest (DS06, DS07)
3
Push
L’
N
L
N
1-10V-
1-10V+
Infrared remote receiver
Daylight sensor
Push
DA
DA
N
L
Infrared remote receiver
Daylight sensor
3
18:00
11:00
12
8:30
Settings on this demonstration: Daylight threshold @ 50lux
With insufcient natural light, the
light switches on at 100%.
The light turns off completely whenever
natural light reaches above pre-set
daylight threshold.
The light automatically turns on at
100% when natural light lux level drops
below pre-set daylight threshold.
On/off Control (DS05)
2
Note:We recommend the mounting distance between sensor to sensor should be more than 2m to prevent sensors from false-triggering.

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 3/4
Wiring Diagram
LED Driver
LED Driver
LED Driver
LED Driver
DS05
DS06
DS07
LED
L
L
N
N
P
L’
N
N
L
DALI
DALI
PUSH
N
L
1-10V
1-10V
L
N
L
N
L
N
1-10V
1-10V
DALI
DALI
DALI
DALI
1-10V
1-10V
220 - 240VAC N
L
N
L
N
L
Double L N terminal makes it easy for wire loop-in and loop-out, and saves the cost of terminal block and assembly time.
Loop-in and Loop-out Terminal (DS05, DS06)
5
* Short Push (<1s): on/off function;
On →Off: the light turns off immediately
Off →On: the light turns on, regardless of the ambient natural light.
* Long Push (>1s): adjust the target lux level by turning the light up or down. Both the adjustment on RC and push switch can overwrite
each other, the last adjustment remains in memory.
Note: if end-user do not want this manual override function, just leave the “push” terminal unconnected to any wire.
Manual Override (DS06, DS07)
4
This sensor reserves the access of manual override function for end-user to switch on/off, or adjust the target lux level by push-switch,
which makes the product more user-friendly and offers more options to t some extra-ordinary demands:

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 4/4
Settings (Remote Control HRC-11)
Press button “RESET”, all settings go back to default settings.
Reset Settings
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
The mode will change to AUTO Mode after power failure.
AUTO/SEMI-AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
Note: the function of SEMI-AUTO is disabled.
ON/
OFF
Press buttons in zone “ Daylight threshold” to set daylight sensor / target lux level
at 2Lux/ 10Lux / 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: 1. to set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button rst.
2. the light never switch off when daylight threshold is preset to disable.
Daylight threshold
1. Press button “Shift”, the red LED is on for indication.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.
Ambient daylight threshold
Test 2s
This button is for test purpose only, light will switch on when natural light lux level is below daylight threshold preset; or switch off when natural light
lux level exceeds daylight threshold preset for 10S.
Note: all other buttons are disabled.
Press these two buttons to adjust the light output brightness and set a new target lux level. The built-in daylight sensor can measure
ambient daylight level from behind the diffuser and calculates how much articial light is needed to maintain the target lux level.
Brightness +/- (for DS06, DS07)
&
A
4
4 hhh
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button
Auto-conguration function (for DS06, DS07)
1. Press button “Shift”, the red LED is on for indication.
2. Select a time period and the sensor will do light level measurement and determine/save the lowest light level (commission line)
with 100% light on, so as to set the target lux level automatically.
Note: 1. Make sure the light level measurement covers the night time.
2. The xture will go into sensor mode after the measurement, all sensor settings remain unchanged.

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 4/4
Additional Information / Documents
1. For full explanation of Hytronik Photocell AdvanceTM technology, please kindly refer to
www.hytronik.com/download ->knowledge ->Introduction of Photocell Advance
2. Regarding Hytronik standard guarantee policy, please refer to
www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy