1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that might
damage the vehicle. When all connections have been made and before mounting
the camera, verify the camera is working and has good view of the area. Then
mount the camera down with the supplied two screws.
2) Connect the RED wire to the +12 volt reverse wire
3) Connect the BLACK wire to ground (a metal, non-painted surface).
4) Run video cable though vehicle, up to video display. (Avoid placing video cable
where it can get pinched or damaged).
5) Attach the YELLOW video rca to camera’s output and to the reverse camera input
of the radio or video display.
6) Attach audible device to camera’s mini pin plug and place audible device in a safe
area (avoid placing video cable where it can get pinched or damaged). Also place
the device where the device can be clearly heard.
NOTE: The camera is supplied with 3 angled mounting plates, (3 degree, 5 degree
and 7 degree) to assure the proper viewing angle of the camera system.
1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that might
damage the vehicle. When all connections have been made and before mounting
the camera, verify the camera is working and has good view of the area. Then
mount the camera down with the supplied two screws.
2) Connect the RED wire to the +12 volt reverse wire
3) Connect the BLACK wire to ground (a metal, non-painted surface).
4) Run video cable though vehicle, up to video display. (Avoid placing video cable
where it can get pinched or damaged).
5) Attach the YELLOW video rca to camera’s output and to the reverse camera input
of the radio or video display.
6) Attach audible device to camera’s mini pin plug and place audible device in a safe
area (avoid placing video cable where it can get pinched or damaged). Also place
the device where the device can be clearly heard.
NOTE: The camera is supplied with 3 angled mounting plates, (3 degree, 5 degree
and 7 degree) to assure the proper viewing angle of the camera system.
II. Connection
II. Connection
I. Specifications
I. Specifications
SENSOR
Effective Pixel
Horizontal Sync Frequency
Vertical Sync Frequency
Scanning System
Sync System
AGC
BLC
Resolution
S/N Ratio
Current Consumption
Power Supply
Operating Temperature
Storage Tempurature
Viewing Angle
Water-Proof
Minimum Illumination
SENSOR
Effective Pixel
Horizontal Sync Frequency
Vertical Sync Frequency
Scanning System
Sync System
AGC
BLC
Resolution
S/N Ratio
Current Consumption
Power Supply
Operating Temperature
Storage Tempurature
Viewing Angle
Water-Proof
Minimum Illumination
CMOS II
656 X 492
15625KHZ
PAL50HZ / NTSC 60HZ
2 : 1 Interlace
Internal
Auto
Auto
420 TV Lines
More Than 48dB
No More 150mA
DC12V ± 10%
-22° ~ 176° F
-40° ~ 176° F
170°
IP67
0.5Lux/F1.2(0Lux with LED)
CMOS II
656 X 492
15625KHZ
PAL50HZ / NTSC 60HZ
2 : 1 Interlace
Internal
Auto
Auto
420 TV Lines
More Than 48dB
No More 150mA
DC12V ± 10%
-22° ~ 176° F
-40° ~ 176° F
170°
IP67
0.5Lux/F1.2(0Lux with LED)
CAMERA
POWER
MINI PIN BUZZER
(RED) 12+
(BLACK) 12-
VIDEO (YELLOW RCA)
CAMERA
POWER
MINI PIN BUZZER
(RED) 12+
(BLACK) 12-
VIDEO (YELLOW RCA)
The TE-CPSS is a camera and parking sensor system all in one unit,
with an audible warning device to alert drivers as well as an on
screen display showing distance to object.
The TE-CPSS is a camera and parking sensor system all in one unit,
with an audible warning device to alert drivers as well as an on
screen display showing distance to object.
