IBM PC 300GL Types 6275 User manual

Personal Computer
Installing Options in Your Personal Computer
PC 300PL Type 6862
PC 300GL Type 6275

Personal Computer
Installing Options in Your Personal Computer
PC 300PL Type 6862
PC 300GL Type 6275
IBM

Note
Before using this information and the product it supports, be sure to read the general information
under Appendix D, “Notices” on page 87.
First Edition (May 1998)
The following paragraph does not apply to the United Kingdom or any country where such provisions
are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES
THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time.
This publication was developed for products and services offered in the United States of America. IBM
may not offer the products, services, or features discussed in this document in other countries, and the
information is subject to change without notice. Consult your local IBM representative for information
on the products, services, and features available in your area.
Requests for technical information about IBM products should be made to your IBM reseller or IBM
marketing representative.
 Copyright International Business Machines Corporation 1998. All rights reserved.
Note to U.S. Government Users — Documentation related to restricted rights — Use, duplication or
disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Laser Compliance Statement ................................ vi
Lithium Battery Notice .................................. vii
About This Book ..................................... viii
How This Book Is Organized ............................... ix
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Chapter 1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Options and Features .................................... 2
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Handling Static-Sensitive Devices ............................ 5
Chapter 2. Preparing to Install and Remove Options ................ 6
Disconnecting Cables and Removing the Cover .................... 6
Locating Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Internal View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Input/Output Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 3. Working with Options on the System Board .............. 11
Accessing the System Board ................................ 12
Identifying Parts on the System Board .......................... 13
Working with System Memory .............................. 14
Memory Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installing a Memory Module .............................. 16
Removing a Memory Module ............................. 18
Installing a Video-Memory Module .......................... 20
Replacing a Microprocessor ................................ 22
Chapter 4. Working with Adapters ........................... 26
Adapters and the Riser Card ............................... 27
Adapter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Plug and Play Adapters ................................. 29
Legacy Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installing Adapters in the Riser Card .......................... 31
Removing Adapters from the Riser Card ........................ 34
Installing an AGP Adapter ................................. 37
Removing the Side Cover ................................. 39
Replacing the Side Cover ................................. 40
 Copyright IBM Corp. 1998 iii

Removing the System Board ................................ 41
Routing a Cable from an Adapter to a Drive in Bay 1, 2, or 3 ........... 43
Chapter 5. Working with Internal Drives ....................... 45
Internal Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Power and Signal Cables ................................ 48
Accessing Drive Bays .................................... 50
Removing the Metal Shield ............................... 51
Installing a Bay Panel .................................. 53
Working with Drives in Bays 1, 2, and 3 ........................ 54
Rotating the Drive Cage ................................. 54
Installing a Drive in Bay 1, 2, or 3 .......................... 56
Removing a Drive from Bay 1, 2, or 3 ........................ 59
Rotating the Drive Cage Back into Fixed Position ................. 61
Working With Drives in Bay 4 .............................. 62
Removing a Drive from Bay 4 ............................. 62
Installing a Drive in Bay 4 ............................... 64
Chapter 6. Working with Security Options ...................... 66
Installing a U-Bolt ...................................... 67
Erasing Lost or Forgotten Passwords .......................... 70
Chapter 7. Completing the Installation ........................ 73
Replacing the Cover and Connecting the Cables .................... 74
Updating the Computer Configuration ......................... 76
Starting the Configuration/Setup Utility Program ................. 77
Changing Settings and Exiting ............................. 79
Configuring an ISA Legacy Adapter ......................... 80
Configuring Startup Devices .............................. 81
Appendix A. PC 300PL Asset Security Settings ................... 82
Appendix B. Changing the Battery ........................... 83
Appendix C. Interrupt and DMA Resources ..................... 85
Appendix D. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
iv Installing Options in Your Personal Computer

Safety Information
Turn everything OFF.
Attach signal cables to
receptacles.
First, remove power cord from
outlet.
To Disconnect
Turn device ON.
DANGER:
Turn everything OFF.
To Connect
Remove signal cables from
receptacles.
Remove all cables from devices.
Attach power cord to outlet.
First, attach all cables to devices.
In the U.K., by law, the power
cord must be disconnected after the
telephone line cable.
2
In the U.K., by law, the telephone
cable must be connected after the
power cord.
12
1
Electrical current from power, telephone, and communication
cables is hazardous. To avoid shock hazard, connect and
disconnect cables as shown below when installing, moving or
opening the covers of this product or attached devices. The
power cord must be used with a properly grounded outlet.
 Copyright IBM Corp. 1998 v

Laser Compliance Statement
Some IBM Personal Computer models are equipped from the factory with a
CD-ROM drive. CD-ROM drives are also sold separately as options. The CD-ROM
drive is a laser product. The CD-ROM drive is certified in the U.S. to conform to
the requirements of the Department of Health and Human Services 21 Code of
Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
Elsewhere, the drive is certified to conform to the requirements of the International
Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser
products.
When a CD-ROM drive is installed, note the following.
CAUTION:
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
Removing the covers of the CD-ROM drive could result in exposure to hazardous
laser radiation. There are no serviceable parts inside the CD-ROM drive. Do not
remove the CD-ROM drive covers.
Some CD-ROM drives contain an embedded Class 3A or Class 3B laser diode. Note
the following.
DANGER
Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the beam.
vi Installing Options in Your Personal Computer

Lithium Battery Notice
CAUTION:
Danger of explosion if battery is incorrectly replaced.
When replacing the battery, use only IBM Part Number 33F8354 or an equivalent
type battery recommended by the manufacturer. The battery contains lithium
and can explode if not properly used, handled, or disposed of.
Do not:
Throw or immerse into water
Heat to more than 100°C (212°F)
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
ATTENTION
Danger d'explosion en cas de remplacement incorrect de la batterie.
Remplacer uniquement par une batterie IBM de type 33F8354 ou d'un type
équivalent recommandé par le fabricant. La batterie contient du lithium et peut
exploser en cas de mauvaise utilisation, de mauvaise manipulation ou de mise au
rebut inappropriée.
Ne pas :
Lancer ou plonger dans l'eau
Chauffer à plus de 100°C (212°F)
Réparer ou désassembler
Mettre au rebut les batteries usagées conformément aux règlements locaux.
Safety Information vii

About This Book
Thank you for selecting an IBM Personal Computer.
This book provides information about the PC 300PL and the PC 300GL. It provides
instructions for installing, removing, and replacing most options. Also, this book
contains information to help you decide which options to add to your computer.
Some illustrations in this publication might be slightly different from your
hardware.
viii  Copyright IBM Corp. 1998

How This Book Is Organized
This book contains the following chapters and appendixes:
Chapter 1, “Overview” provides an introduction to the options and features for
your computer. Safety precautions and handling techniques are discussed along
with the required tools you will need to install and remove options.
Chapter 2, “Preparing to Install and Remove Options” provides instructions for
removing the cover and cables for your computer and for locating the
components you want to work with.
Chapter 3, “Working with Options on the System Board” provides instructions
for locating, accessing, and working with options on the system board.
Chapter 4, “Working with Adapters” provides instructions for installing and
removing adapters.
Chapter 5, “Working with Internal Drives” provides instructions for installing
and removing internal drives.
Chapter 6, “Working with Security Options” describes features such as the
security U-bolt and erasing lost or forgotten passwords.
Chapter 7, “Completing the Installation” provides instructions for reassembling
your computer after you have finished installing options. Information about
using the Configuration/Setup Utility program is also provided.
Appendix A, “PC 300PL Asset Security Settings” provides important
information for the PC 300PL. If you have a PC 300PL model, and have set an
administrator password, read this section before removing the computer cover
or internal components.
Appendix B, “Changing the Battery” explains how to change your computer
backup battery and the precautions to take when handling and disposing of the
battery.
Appendix C, “Interrupt and DMA Resources” contains the default interrupt and
direct memory access (DMA) resources for your computer.
Appendix D, “Notices” contains IBM notices and trademark information.
About This Book ix

Related Publications
The following publications, together with this book, contain information about your
computer.
Setting Up Your Personal Computer
This publication contains instructions to help you set up your computer.
Using Your Personal Computer
This publication contains the following:
– Instructions for configuring, operating, and maintaining your computer
– Information on diagnosing and solving computer problems and how to get
help and service
– Warranty information
Understanding Your Personal Computer
This online publication (provided on the Ready-to-Configure Utility Program CD
and with the preinstalled software) includes general information about using
personal computers and in-depth information about the specific features of your
computer.
About Your Software
This publication (provided only with computers that have IBM-preinstalled
software) contains information about the preinstalled software package.
Your Ready-to-Configure Utility Program CD
This publication contains information about the Ready-to-Configure Utility
Program CD for your computer. The publication also contains instructions for
starting the CD.
The following publications contain more information about your computer.
Hardware Maintenance Manual
This publication contains information for trained service technicians. To obtain
a copy, refer to the section on ordering publications in the "Getting Help,
Service, and Information" chapter in Using Your Personal Computer. Also, this
publication is on the World Wide Web at:
http://www.pc.ibm.com/us/cdt/hmm.html
xInstalling Options in Your Personal Computer

Technical Information Manual
This publication contains more information about the technical aspects of your
computer. It is available on the World Wide Web at:
http://www.pc.ibm.com/us/support/treport.html
About This Book xi

xii Installing Options in Your Personal Computer

Chapter 1. Overview
Adding hardware options to your computer is an easy way to increase its
capabilities. Instructions for removing, installing, and replacing options and
features are included in this book. When adding an option, use these instructions
along with the instructions that come with the option. If you have installed options
before, you might be able to perform some activities without detailed instructions.
This chapter provides a brief introduction to the options and features that are
available for your computer. Also, important information about required tools,
electrical safety, and static-sensitive devices is discussed.
Important
Before you install or remove any option, read the safety procedures and
component-handling guidelines in this chapter. These precautions and
guidelines will help you work safely.
Refer to Using Your Personal Computer for general information on the use, operation,
and maintenance of your computer. Using Your Personal Computer also contains
information to help you solve problems and get repair service or other technical
assistance.
 Copyright IBM Corp. 1998 1

Options and Features
The following are some of the available options and features that are discussed in
this book:
System board components
– System memory, called dual in-line memory modules (DIMMs)
– Video memory, a small, outline DIMM (SODIMM) (PC 300PL models only)
– Microprocessor
– Jumper for clearing CMOS and erasing lost or forgotten passwords
– Battery
Adapters
– Industry standard architecture (ISA) adapters
– Peripheral component interconnect (PCI) adapters
– Accelerated Graphics Port (AGP) adapters (PC 300PL models only)
Internal drives
– CD-ROM
– Hard disk
– Security U-bolt
The following are some other available options and features for your computer.
For more information, refer to the documentation that comes with the optional
hardware.
– If your computer does not have an Ethernet connector, you can add a Wake
on LAN adapter.
– To help with power management, you can add a modem and have your
computer start when a ring is detected by the modem. Using an internal
modem, you can use the Configuration/Setup Utility program to enable
Modem Ring Detect, or using an external modem, you can enable Serial Port
Ring Detect. For more information, see Using Your Personal Computer.
2Installing Options in Your Personal Computer

IBM provides help in selecting drives, cables, and other options for your
computer. For the latest information about available options:
– Within the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM
reseller, or IBM marketing executive.
– Within Canada, call 1-800-565-3344 or 1-800-465-7999.
– Outside the United States and Canada, contact IBM, your IBM reseller, or
IBM marketing executive.
IBM maintains pages on the World Wide Web where you can get information about
IBM products and services, find the latest technical information, and download
device drivers and updates. Some of these pages are:
http://www.ibm.com Main IBM home page
http://www.pc.ibm.com IBM Personal Computer home
page
http://www.pc.ibm.com/us/desktop/ IBM Commercial Desktop home
page
http://www.ibm.com/servers/ IBM PC Server and Netfinity
Server home page
http://www.pc.ibm.com/us/options/ IBM Options home page
http://www.pc.ibm.com/us/intellistation IBM IntelliStation home page
http://www.pc.ibm.com/us/thinkpad/ IBM ThinkPad home page
Tools Required
To install or remove options in your computer, you will need a flat-head
screwdriver. Any additional tools needed depend on the specific option and are
noted in the instructions that come with the option.
Chapter 1. Overview 3

Electrical Safety
CAUTION:
Electrical current from power, telephone, and communication cables can be
hazardous. To avoid any shock hazard, disconnect all power cords and cables as
described in the following information.
Attention: The presence of 5 V standby power might result in damage to your
hardware unless you disconnect the power cord from the wall before opening the
computer cover.
For your safety, always do the following before removing the cover:
1. Shut down all programs as described in your operating-system documentation.
2. Turn off the computer and any attached devices, such as printers, monitors, and
external drives.
Note: Personal computer users in the United Kingdom who have a modem or
fax machine attached to their computer must disconnect the telephone
line from the computer before unplugging any power cords (also known
as power cables). When the computer is reassembled, users must
reconnect the telephone line after plugging in the power cords.
3. Unplug all power cords from electrical outlets.
4. Disconnect all communication cables from external receptacles.
5. Disconnect all cables and power cords from the back of the computer.
Note: Do not reconnect any cables or power cords until you reassemble the
computer and put the cover back on.
CAUTION:
Never remove the cover on the power supply. If you have a problem with the
power supply, have your computer serviced.
4Installing Options in Your Personal Computer

Handling Static-Sensitive Devices
Have you ever walked across a carpeted floor, then touched an object and received
a small electrical shock? That's static electricity, and although harmless to you, it
can seriously damage computer components and options.
Important
When you add an option, do not open the static-protective package containing
the option until you are instructed to do so.
When you handle options and other computer components, take these precautions
to avoid static electricity damage:
Limit your movement. Movement can cause static electricity to build up around
you.
Always handle components carefully. Handle adapters and memory-modules
by the edges. Never touch any exposed circuitry.
Prevent others from touching components.
When you are installing a new option, touch the static-protective package
containing the option to a metal expansion-slot cover or other unpainted metal
surface on the computer for at least two seconds. This reduces static electricity
in the package and your body.
When possible, remove the option and install it directly in the computer without
setting the option down. When this is not possible, place the static-protective
package that the option came in on a smooth, level surface and place the option
on it.
Do not place the option on the computer cover or other metal surface.
Chapter 1. Overview 5

Chapter 2. Preparing to Install and Remove Options
This chapter provides instructions for accessing and locating the options you want
to install or remove.
Disconnecting Cables and Removing the Cover
Before you begin
Read “Electrical Safety” on page 4 and “Handling Static-Sensitive Devices”
on page 5.
Remove any media (diskettes, compact discs, or tapes) from the drives, and
then turn off all attached devices and the computer.
1Unplug all power cords from electrical outlets. If you have a modem or fax
machine attached to your computer, disconnect the telephone line from the
wall outlet and the computer.
2Disconnect all cables attached to the computer; this includes power cords,
input/output (I/O) cables, and any other cables connected to the computer.
Note: For more information on ports, including universal serial bus (USB),
refer to Understanding Your Personal Computer.
Ethernet Audio
Serial
Device
Keyboard Mouse
USB
Device
Monitor Parallel
Device
6  Copyright IBM Corp. 1998