ICP DAS USA MP-8 43 Series User manual

MP-8x43 Getting Started
V 1.0
http://www.icpdas.com MP-8x43 Getting Started V1.0 1

A English Version
1.1 hardware setup and basic setting
In this section we will introduce for basic setting for WinCE and use the
EzConfig tools to test the digital IO.
1.1.1 MP-8x43 wire connection
The main hardware of MP-8343 is showed as below. It includes VGA,USB,
Compact Flash, COM Port, Ethernet and interface for I/O modules。
The picture is for MP-8343. It has standard 15 pin VGA port ,USB,
Ethernet and RS232/485(COM2~5) communication port.
Overview Item
Descriptions
1. Power LED Indicator
2. Rotary Switch
3. Ethernet Port 1
4. USB 2.0 Ports
5. COM Port 5 (RS-232)
6. COM Port 4 (RS-232/RS-485)
7. Power Switch
8. COM Port 2 (RS-232)
9. Power and Ground
10. COM Port 3 (RS-485)
11. Redundant Power and
Ground
12. Relay Output R.COM and .NO
13. Frame Ground
14. Ethernet Port 2
15. CF (Compact Flash) Card Slot
16. VGA Port
17.Slot1~Slot3
18.DIPSwitch
For more information of dimension, please refer to Appendix A.
http://www.icpdas.com MP-8x43 Getting Started V1.0 2

1.1.2 Quick hardware setup
What’s on your package?
Item Quantity Model No. Description
MP-8343
MP-8343: 3 slots
MP-8000 1 MP-8743: 7 slots
MP-8743
Manual 1 -
Quick Start Guide
(this manual)
CF Card 1 - Rescue CF Card
CD 1 -
Software and
documents
included.
2.4 mm Screw
driver
Screw Driver 1 1C016
Preparing for start-up your MP-8000:
1. Power Supply: +10 ~ +30 V (Ex: DP-1200)
DC
http://www.icpdas.com/products/Accessories/power_supply/power_list.htm
2. Monitor: 640 x 480 ~ 1024 x 768 (or above)
3. USB mouse and USB keyboard
4. Ethernet Switch (Ex:NS-205), and Ethernet Cable
5.I-8000 High profile I/O modules
http://www.icpdas.com MP-8x43 Getting Started V1.0 3

6. Setup:
1. Plug the USB mouse into USB interface.
2. Plug the I/O Modules into I/O slot, and make sure that was installed
correctly.
3. Connect the monitor VGA cable to MP-8000 VGA port, and connect
monitor power cable to properly power source and turn it on .
4. Connect the Ethernet port to the Ethernet Switch with Ethernet Cable.
5. Connect the DC 24V power from the power supply, and make sure
that was installed correctly.
6. Turn on the DC 24V power supply。
USB
mouse/ke
y
board
2. install modules
1. Plug USB mouse
5. conect the DC 24V
p
ower
4. connect Etherne
t
3. connect the VAG
p
or
t
Ethernet
i8K I/O
modules
PC
http://www.icpdas.com MP-8x43 Getting Started V1.0 4

After power-on and boot up the monitor will show as below:
1.1.3 Windows CE system basic setting
zSetting the Date and time :
1. use the mouse select
“start” ÆSetting(S) Æ
Control Panel(C)，
Open the Control
Panel。
2. Double click
“Date/Time” icon，
Open the dialog。
3. After setting the date
and time, please click
the “Apply＂
http://www.icpdas.com MP-8x43 Getting Started V1.0 5

zSetting the IP address for Ethernet:
If use the DHCP you don’t need to read this section.
1. Setect “Start” ÆSetting(S) Æ
Network and dial-up
Connections (N).
2. Double click “PCI-FETCE5B1/2”
icon，show the Ethernet Adapter
setting dialog.
3. selected “Specify an IP
Address(S)”,and set the IP
Address位址(A),Subnet
Mask(U
zMP-8000 's System setting will be saved automatically. The next
booting up will become effective.
),default gateway(G).
4. select “Name Servers” Tab,and
setting the Primary
DNS(D),Secondary DNS(N).
5. Click “OK” for finishing this
setting。
http://www.icpdas.com MP-8x43 Getting Started V1.0 6

1.2 Easy test for digital IO module
Open the EzConfig
Click the
Start->programs->ICPDAS->E
zProg-I->EzConfig
Will show the EzConfig main
dialog:
1 => click the Scan Slot button
12 => and select “Yes”
EzConfig will find out all modules
that had been plugged in the slots
automatically.
2
This demo for I-8054W module,
Connect DI 0~7 to DO 0~7 one
by one
http://www.icpdas.com MP-8x43 Getting Started V1.0 7

3 => use the mouse click the
module in monitor. That will
show the module IO status.
3 4 => The Y(DO) that you can click
that to control the output
on/off status.
4
Show I-8054W as below:
5 =>Click the Y0,Y1,Y2,Y3 as ON
6 6 => the DI X0,1,2,3 show ON,
8And the module’s LED DO
0,1,2,3 will show ON at the
same time, DI 0,1,2,3 show ON,
5
Click the Y0,Y1,Y2,Y3 to OFF
7
7 =>after test, please click the “ok”
8 =>Click the Save button and click
the “OK” to confirm to save the
system setting
In this sample, we can easily control the IO by using the EzConfig tool. For
more information please refer to related manuals.
http://www.icpdas.com MP-8x43 Getting Started V1.0 8

B中文版
1.1硬體安裝與設定
在這個章節將介紹設定 PAC 的一些工具，你可以使用控制台改變系統時間或
網路的設定，及一些關於 WinCE 的設置與使用 EzConfig 監控 IO。
1.1.1 MP-8x43 外觀介紹
MP-8343 主要的硬體描述如下圖，其中包括了 VGA、USB、Compact Flash、
COM Port、Ethernet 和基本的 I/O 插槽介面。
圖中是 MP-8343 硬體的樣本，15 pin VGA port 是電腦螢幕標準介面，並且能
配合 USB 或RS232 支援觸控螢幕。COM2~5 是RS232/485 通訊埠，包含標準
Ethernet 網路。
安裝接線說明
1. Power LED Indicator
2. Rotary Switch
3. Ethernet Port 1
4. USB 2.0 Ports
5. COM Port 5 (RS-232)
6. COM Port 4 (RS-232/RS-485)
7. Power Switch
8. COM Port 2 (RS-232)
9. Power and Ground
10. COM Port 3 (RS-485)
11. Redundant Power and round
12. Relay Output R.COM and .NO
13. Frame Ground
14. Ethernet Port 2
15. CF (Compact Flash) Card Slot
16. VGA Port
17.Slot1~Slot3
18.DIPSwitch
詳細外觀安裝尺寸請參閱附錄 A
http://www.icpdas.com MP-8x43 Getting Started V1.0 9

1.1.2 快速硬體安裝
拆開包裝後您應該可以發現下列物品:
項目 數量 型號 說明
MP-8343 硬體模組
MP-8000 MP-8343: 3 槽
1
MP-8743 MP-8743: 7 槽
手冊 ( )
1 -
快速安裝指南 本文件
CF Card 1 - 系統回復,
CD 1 - 內含軟體 手冊
螺絲起子 1 1C016 2.4 mm ㄧ字螺絲起子
安裝準備事項:
1. 電源供應器: +10 ~ +30 V (例如: DP-1200)
DC
http://www.icpdas.com/products/Accessories/power_supply/power_list.htm
2. 有D-SUB 15針接頭的標準VGA螢幕,與電源
3. 標準 USB 滑鼠
4. 網路集線器(如NS-205),與網路線
5. PAC 支援的 I-8000 高卡IO 模組
6. 安裝步驟: (如下圖)
USB 到USB插孔。
1. 插入 滑鼠
2. 找空的插槽位置，將IO 對準插入插槽,並確認已正確插到底。模組
VGA 源。
3. 連接 螢幕與螢幕電
4. 。連接網路線到集線器
5. 24V 源, 正負不要接反了。正確接上 直流電 小心
認正確後開啟24V 源,與 源約 60 秒後即可開機完成。
6. 確 直流電 螢幕電
http://www.icpdas.com MP-8x43 Getting Started V1.0 10